Redx RX-5000AC User manual

www.redx.com.au
RX - 5000AC
All-In-One Energy Storage System
Quick Installation Guide

Warning
Warning
Notice
This document is subject to change from time to time due to product upgrades or other reasons.
This document is not a substitute for the user manual or safety instructions.
Please read the user manual and related standards before undertaking any operation or
commissioning. Please take time to accesshttp://www.redx.com.au or scan the QR code for the
latest quick installation guide.
Failure to comply with any of the above requirements may result in injury to personnel or damage
to equipment.
Prior to commencement, check whether the goods match the packing list, if there is any damage
to any items or components missing, please contact the Distributor / Dealer or Redx.
The power cables must be intact and well insulated. Please use insulating gloves and wear personal
protective equipment at all times when installing this product.
All safety labels, warning labels, andnameplates must be clear and visible andcannot be
removed or overwritten.
Hot surface!
Inverter module may become hot after extended period of operation. Allow time for inverter
to cool before touching!
The country setting and protection parameters must be set by professional personnel based
on local power grid standards.
Incorrect country settings may affect the operation failure to meet the local standard.
Warning Label
Disconnect all external power supplies before
maintainace.
Device has high voltage on AC input and AC
output. Professional and qualified technicians are
required to install this unit.
Hot surfaces！
Read the instructions before
operation.
Wait for 5 minutes before touching the internal conductive components after system
turn off and disconnected from grid.
5min
Redx shall not be liable for any loss of life or damage caused by failure to comply with the
requirements of this document and user manual.
Safety Statement
Danger
Shock hazard！
Exposure to sunlight and the elements are not recommended.
All electrical connections must meet local and national electrical standards.
Only connect the system to the grid with local authority approval.
Warranty will be void if the cover is removed. Improper opening of the unit may also result in
serious electrical shock or injury to personnel.

Packing List
RX-5000AC Standard Accessories
Cover&Connection Components
2PCS
M6*14
Countersunk Screw
Communication Cable1
2PCS
Inverter Terminal
Cover
1PCS
EPS Load Connector
1PCS
Bootlace
Ferrule-0510
30PCS
Bootlace
Ferrule-6012
3PCS
Grid Connector
1PCS
Communication
Connector
1PCS
1PCS 1PCS 1PCS
Pe Cable2 Communication Cable2 RX-0050
RX-5000AC
1PCS
Inverter Bracket
1PCS
Hole Template
1PCS
WI-FI/4G Dongle
(Optional)
1PCS
M6
Expansion Bolt
10PCS
Bat Power Cable 1
2PCS
Bat Power Cable 2
2PCS
1PCS
Pe Cable1
2PCS
SC6-6
2PCS
Smartmeter/CT-Cable
4PCS
Document
Information
Smartmeter+CT
(Optional)
2PCS

620mm
1400mm
Dimension
176mm176mm
Base Option
1PCS 1PCS 2PCS 8PCS
Base
1PCS
Base leveling screw
4PCS
RX-0050 Accessories
Battery Body
2PCS
Battery Cover Battery Bracket
M6*10
Countersunk Screw
M6*50
Expansion Bolt
2pcs
M4*8
Countersunk Screw
4PCS 1PCS
Information
Document Bat Hole Template
1PCS
M6*10
1PCS
M4*20

Installation Location
Pre - Operation Inspection
①
②
③
④
⑤
⑥
⑦
The installation location meets the requirement.
Checking Items
The system has been securely installed.
Sufficient space for heat dissipation. No objects are left onthe system.
System wiring is normal and firm.
Cables are properly installed and well protected without any damage.
All terminals have been sealed.
Warning labels are not covered without alteration or occlusion.
Result
YES NO
Operation
Following the steps to start the system.
Step① : Connect 240V Grid to inverter
Step : T② urn on the inverter power button
Step③: Turn on the battery isolation circuit breakers
Step④ : Open the Redx Power Redx App, login to your installer account
No snow exposure
No direct sunlight No rain exposure
Direct sunlight Rain exposure Snow exposure
Step ® : Complete all installation steps in the App instructions

Installation
Avoid water and electricity when drilling, bit size φ8mm, drilling depth 40mm.
Battery Connection
13
2
Power Cable
Battery to battery PE Cable
M6
5 N.M
Note：
Com2of Bat1 connects to
Com1of Bat2
COM1
COM2
Communication
Cable
BAT2
BAT1
13
2
46
5
79
8
5000AC
MODEL NO. :
PROJ. NO. :
Inverter
Bracket
Battery
Bracket
M6
2.8 N.M
1
Cover
Hole Template
Refer to the electrical
connection section for wiring
M6×14
Plug
Plug
Expansion Bolts
Screw
M4
1.2 N.M
M6
5 N.M
M6
5 N.M
Spacer
Long PE cable
connects to inverter
Note:Any exposed cable between battery and inverter must be covered with UV rated conduit

Battery Power Cable Wiring
WiFi/4G Dongle
Note: You will hear a ‘Click’ sound when the battery connector is fully connected.
When removing a battery cable, press the button on the cable terminal.
Click
Tighten connector on the thread once Dongle is in.
Note: An external DC Isolator is required when connecting the batteries to the
inverter (2 pole 125A DC - Supplied).

Grid Connection
1
3
12mm
AB
2
Communication Connection
1 10
20
30
11
21
1A1
A2
A3
A4
A5
A6
B1
B2
B3
C1
C2
C3
C4
C5
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Pin
20
16
17
18
19
21
22
23
24
25
26
27
28
29
30
Pin Pin
Definition
Group Group
//
Dry contact 1 public
Dry contact 1 open
Dry contact 1 close
Dry contact 2 public
Dry contact 2 open
Dry contact 2 close
485D+
485D-
GND
BMS_CAML
BMS_CANH
GND
BMS_485A+
BMS_485A-
B8
B7
B6
B5
B4
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
DRM0-
DRM0+
GND
485C-
485C+
Negative Input For Switch
Positive Input For Switch
CT+
CT-
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Bootlace Ferrule-0510
10mm
1 2
Note: Cable COM1 connected to inverter communications plug connects to COM1 port of Bat1.

3
AB C
12mm
AB
12
3
EPS Load Connection
Bootlace
Ferrule-6012
Tighten latchscrew once connector is in.

Notice
If the startup fails, refer to "Troubleshooting" in the user manual.
For details about LED indicators, refer to the user manual.
LED Indicator
System indicator
PV indicator
Battery indicator
Green flash
Green Normal
System warning
System fault
No PV
PV CT is connected
-
-
No battery
Yellow
Yellow
Red
Red
Not lit
Not lit
Green flash
Green Solid
Yellow
Red
Discharging
Charging
Battery warning
Battery fault
Not lit
Green Flash
Green Solid
Yellow
Red
Green
Startup conditions are not met
Grid disconnected
-
Inverter synchronised with grid
Grid warning
-
Grid indicator
CT / Meter Installation
Grid
Smartmeter
Smartmeter
CT
CT
Third Party
Inverter
①
①
②
②
RX-5000AC GRID L-Line Grid CT①
GRID
Third Party
Inverter
L-Line PV CT②
RX-5000AC
The CT with the
"Grid" label is
attached to the L
line of the grid
cable. The "Grid"
CT arrow points
towards the
power grid. The
"PV" CT arrow
points from the
PV Inverter to the
switchboard. The
CTs must be
installed inside
the switchboard.

5000AC User Manual
5000AC Quick Installation Guide
5000AC Warranty Card
Redx App Download
The size and parameters of the product are subject to change without notice.
Rev 2023.04.13
Redx Power App Installer Manual
RX-0050 User Manual
Redx Power App User Manual
Redx.com.au Downloads