Redx RX-2505AC User manual

All-In-One Energy Storage System
Quick Installation Guide
www.redxenergy.com.au
RX - 2505AC
Safety Statement
Danger
Warning
Warning
Notice
This document is subject to change from time to time due to product upgrades or other reasons.
This document is not a substitute for the user manual or safety instructions.
Please read the user manual and related standards before undertaking any operation / commissioning. Please
take time to access http://www.redxenergy.com.au or scan the QR code for the latest quick installation guide.
The installation must be completed by well trained, qualified professional technicians. Technicians
must be familiar with safety specifications of electrical systems.
Failure to comply with any of the above requirements may result in injury to personnel or damage
to equipment.
Prior to commencement, check whether the goods match the packing list, if there is any damage to
any items or components missing, please contact the Distributor / Dealer or Redx.
The power cables must be intact and well insulated. Please use insulating gloves and wear personal
protective equipment at all times when installing this Product.
All safety labels, warning labels, and nameplates must be clear and visible and cannot be
removed or modified.
Burn hazard！
Do not touch the inverter module for maintenance immediately after long time operation.
The country settings and protection parameters must be set by professional technician based
on local power grid standards.
Incorrect country settings may affect the operation of the unit adversely and may result in failure
to meet the local standard.
Warning Label
Disconnect all external power
supplies before maintainace.
High Voltage！
Only professional and qualified technicians
are allowed to install and operate
Hot surfaces！
Read all instructions before
operation.
Wait for 5 minutes before touching the internal conductive components after system
has been turned off and disconnected from grid.
5min
Redx shall not be liable for any loss of life or damage caused by failure to comply with the
requirements of this document and user manual.
Shock hazard！
Exposure to sunlight and the elements is not recommended
All electrical connections must be completed by professional technicians only.
All electrical connections must meet local and national electrical standards.
Only connect the system to the grid with local authority approval .
Warranty will be void if the cover is removed. Improper opening of the unit may also result in
serious electrical shock or injury to personnel.

This drawing is for reference only. Please refer to the actual product.
600
900
The size and parameters of the product are subject to change without notice.
Packing List
Installation Location
Dimension
145
RX-2505AC
Mounting
Bracket
Expansion
Bolts RJ45
Connector
1PCS
Information
1PCS 5 PCS 1PCS
4Pin
Connector
1PCS
M5
Connector M4
Connector CT Hole
Template
1 PCS 5PCS 2 PCS 1PCS Documents 1PCS
http:// www.redxenergy.com.au
http:// www.redxenergy.com.au/downloads/
Redx App Download
≥300mm ≥300mm
Hot surface
≥300mm ≥300mm
Hot surface

Installation
Grounding Connection
RS485 Installation
1 3 5
24
5
Locating Plate Expansion Bolts
6
Locating Plate Nut / washer Stand
4
Avoid water and electricity when drilling, bit size φ8mm, drilling depth 40mm.
This figure is for reference only, please refer to the actual product!
Customers could connect their own WiFi
module,to replace the built-in WiFi module
with the same communication port.
Refer to the RX - 2505AC manual for the
detail of the RS485 installtion.
Notice
RX-2505AC
Bracket
123 4
2 31
1
+5V 485 A GND
2 3 4
-485 B -
CT or smartmeter Installation (choose one of them）
1
2
4
6
5
3
RX-2505AC
Mark
Mark
4Pin
Connector
RX-2505AC
4Pin
Connector
Nut
CT_GRID
CT_PV
Connector
CT_GRID - ( )
CT_PV - ( Black )
CT_GRID + ( )
CT_PV + ( )
Waterproof Sealing Ring
Nut
4Pin Connector
M2.5
1 N.M
Screw
Notice
CT
L-Line
GRID
Load
1
2
N
1
2
N
CT_PV +
CT_PV -
CT_GRID +
CT_GRID -
CT
L-Line
4Pin Connector diagramMiddle Connector diagram
1
2
CT_PV +
CT_PV -
CT_GRID +
CT_GRID -
The CT with the "GRID" label is
connected to the L line of the
power grid. If there is a solar
inverter at home, you can
connect the CT with "PV" label
to the Lline of the inverter. The
"GRID" CT arrow points towards
the grid. The "PV" CT arrow
points from PV to power panel.

Pre - Operation Inspection
①
②
③
④
⑤
⑥
⑦
⑧
The installation location meets the requirement.
Checking Items
The system has been securely installed.
Sufficient space for heat dissipation. No objects are left in the system.
System wiring is correct and firm. Refer to 240V diagram for more information.
Cables are properly installed and well protected without any damage.
The selection of AC circuit breaker meets local standard.
All terminals have been sealed.
Warning labels are not covered without alteration or occlusion.
Result
YES NO
Notice
If the startup fails, refer to "Troubleshooting" in the user manual. For details about
LED indicators, refer to the user manual.
①
③
④
Operation
Following the steps to start the system.
Step : Connect to the grid.
②
Step : Turn on the battery isolation circuit breaker.
Step : Turn on the power button.
Step : Download the Redx Power App, QR Code for App download is on flip side of the document
Step⑤: Complete all steps in the App instructions.
Operating
status
RUN Operation----Green
Fault----Red
Grid ----Green
No Grid ----Blue
Charge---Green
Discharge---Blue
VPP
GRID
BAT
SOC Battery Capacity
LED Status
Monitoring ----Green(Flash)
Remote Control ----Blue(Flash)
On/Off grid installation
1 5
3
8
2
9
6 7
2
4
L=E+(2~3) mm
E
1
M4
1.5 N.M
DRM0 Installation
1
R
J45
RJ45
Connector
Waterproof Sealing
Ring
RJ45
Connector
Network
Cable
5
6
7
8
4
3
2
1
1
2
Nut
GRID N
GRID PE
EPS PE
EPS L
Waterproof Sealing Rings
GRID L
ConnectionPlate
EPS N
Nut
Nut
RUN
VPP
GRID
BAT BATT