IBM Storwize V7000 User manual

IBM Storwize V7000 Unified
Quick Installation Guide
GA32-1056-07


Note
Before using this information and the product it supports, read the general information in “Notices” on page 77, the
information in the “Safety and environmental notices” on page ix, as well as the information in the IBM Environmental
Notices and User Guide , which is provided on a DVD.
This edition applies to IBM Storwize V7000 Unified and to all subsequent releases and modifications until otherwise
indicated in new editions.
This edition replaces GA32-1056-06.
© Copyright IBM Corporation 2011, 2012.
US Government Users Restricted Rights – Use, duplication or disclosure restricted by GSA ADP Schedule Contract
with IBM Corp.

Contents
Figures ...............v
Tables ...............vii
Safety and environmental notices . . . ix
Safety ................ix
Safety statements ............xi
Sound pressure .............xv
About this guide ..........xvii
Who should use this guide.........xvii
Accessibility .............xvii
Emphasis ..............xvii
Storwize V7000 Unified library and related
publications .............xviii
How to order IBM publications........xx
Sending your comments ..........xxi
Chapter 1. Before you begin the
installation .............1
Step 1. Reviewing your packing slip ......1
Step 2. Identifying the hardware components . . . 3
Step 3. Verifying environmental requirements . . . 8
Step 4. Reviewing enclosure location guidelines . . 9
Step 5. Gather information .........11
Checking that IP addresses are not already in use 11
Information required before initializing your
system ...............12
Information required before starting initial
configuration of your system .......15
Chapter 2. Performing the hardware
installation .............29
Step 6. Installing the support rails for the enclosures 29
Step 7. Installing the enclosures........32
Step 8. Installing the support rails for file module
slides ................34
Step 9. Installing the file modules .......38
Step 10. Connecting the SAS cables to the expansion
enclosures ...............42
Step 11. Attaching the Ethernet cables .....47
Step 12. Attaching the Fibre Channel cables....52
Step 13. Connecting the power cords ......54
Step 14. Powering the system on and off ....56
Chapter 3. Initializing the system . . . 63
Step 15. Using InitTool.exe on the USB flash drive 63
Step 16. Initialize the Storwize V7000 ......64
Step 17. Initializing the file modules ......65
Chapter 4. Configuring the system. . . 67
Step 18. Configuring the system using the
management GUI ............67
Step 19. Change default passwords ......68
Step 20. Check the Storwize V7000 Unified system
status ................69
Step 21. Upgrade the Storwize V7000 Unified
software ...............69
Step 22. Problems with initial configuration . . . 70
Step 23. Enable IBM Tivoli Assist On-Site (AOS) . . 73
Step 24. Registering for My Notification .....73
Step 25. Next steps ............74
Appendix. Accessibility features for
IBM Storwize V7000 Unified ......75
Notices ..............77
Trademarks ..............79
Electronic emission notices .........79
Federal Communications Commission (FCC)
statement ..............79
Industry Canada compliance statement ....80
Avis de conformité à la réglementation
d'Industrie Canada ...........80
Australia and New Zealand Class A Statement 80
European Union Electromagnetic Compatibility
Directive ..............80
Germany Electromagnetic compatibility directive 81
Japan VCCI Council Class A statement ....82
People's Republic of China Class A Electronic
Emission Statement...........82
International Electrotechnical Commission (IEC)
statement ..............82
United Kingdom telecommunications
requirements .............82
Korean Communications Commission (KCC)
Class A Statement ...........82
Russia Electromagnetic Interference (EMI) Class
A Statement .............83
Taiwan Class A compliance statement ....83
European Contact Information ........83
Taiwan Contact Information .........83
© Copyright IBM Corp. 2011, 2012 iii

iv Storwize V7000 Unified: Quick Installation Guide

Figures
1. This figure shows 12 drives and two end caps
(model 2076-112). ...........3
2. This figure shows 24 drives and two end caps
(model 2076-124). ...........4
3. Rear view of a model 2076-112 or a model
2076-124 control enclosure ........4
4. This figure shows the data ports in the rear of
the control enclosure...........5
5. 10 Gbps Ethernet ports on the rear of the
Storwize V7000 enclosure ........6
6. Rear view of a model 2076-212 or a model
2076-224 expansion enclosure .......6
7. SAS ports and LEDs in rear of expansion
enclosure..............7
8. Front view of file module ........8
9. Rear view of file module ........8
10. Recommended rack locations ......10
11. Examples of the IP addresses and network
services needed for the system. The expansion
enclosures are not shown. ........13
12. Here are examples of IP addresses and
network services needed for the system. The
expansion enclosures are not shown. ....16
13. Securing an enclosure to a rack cabinet 30
14. Hole locations in the front of the rack....31
15. Hole locations in the back of the rack ....32
16. Removing the enclosure end cap .....33
17. Securing an enclosure to a rack cabinet 34
18. Cable management arm box contents. ....35
19. Friction rail box contents. ........36
20. Locate a 2U space in the lower section of the
rack. ...............36
21. Open the rear slide rail hooks. ......37
22. Install the rear end of the slide rails. ....37
23. Install the front end of the slide rails. ....38
24. Install the front end of the slide rails. ....38
25. Install the file module on the slide rails. 39
26. Slide the file module into the rack. .....39
27. Install the cable management support arm. It
can be installed on either side (left or right).
The graphic shows the rear of the rack. . . . 40
28. Install the cable management arm. .....40
29. Adjust the location of the cable management
arm. ...............41
30. Connect and route the cables. ......41
31. Secure the cable management arm and the file
module in the rack for shipping if needed. . . 42
32. Install the front screws. ........42
33. Internal cabling connections between the
control enclosure (A) and the expansion
enclosures (B & C). ..........44
34. Attaching an expansion enclosure to the
control enclosure ...........45
35. Adding a second expansion enclosure....46
36. Attaching SAS cables to the enclosures 47
37. Control enclosure Ethernet network
connections. ............48
38. 10 Gbps Ethernet ports on the rear of the
Storwize V7000 enclosure ........49
39. File module Ethernet direct connections. 50
40. Diagram showing how to connect the file
modules to the control enclosure using Fibre
Channel cables. Refer to previous table. . . . 53
41. Unlocking the cable retention bracket ....55
42. Sliding the cable retention bracket directly
behind the power cord .........56
43. 24 drives and two end caps .......57
44. 12 drives and two end caps .......57
45. LEDs on the power supply units of the
expansion enclosure..........58
46. LEDs on the power supply units of the control
enclosure .............59
© Copyright IBM Corp. 2011, 2012 v

vi Storwize V7000 Unified: Quick Installation Guide

Tables
1. Storwize V7000 Unified library .....xviii
2. Other IBM publications ........xx
3. IBM documentation and related websites xx
4. The following IP address information is
required before initializing your system. Fill in
all the information needed in the Value
column before proceeding with this
installation. ............14
5. This table can be used for recording the
information needed for the initial
configuration wizard in the management GUI.
The table entries serve as a guide only. Enter
the Value column with your system
information. ............17
6. Information that the system will provide to
IBM Remote Technical Support ......18
7. All the information in this table is required. 19
8. CIDR subnet mask information ......19
9. Authentication method information. Refer to
the notes above ...........22
10. Active Directory Configuration Information 22
11. LDAP CONFIGURATION INFORMATION 24
12. NIS configuration information ......25
13. Use this table to identify the file module,
control enclosure, and expansion unit port
locations. Follow the links to identify detailed
port locations.............43
14. How to connect SAS cables to expansion units. 44
15. Ethernet connections available with the control
enclosure .............49
16. Ethernet connections available with the file
modules .............50
17. LED status front of control enclosure or
expansion enclosure. Refers to item [1] in the
figures above. ............57
18. LED status rear of expansion enclosure. 58
19. LED status when control enclosure is powered
on................59
20. Create two files and enter one line each,
adjusted to the values fitting to your
environment. ............64
© Copyright IBM Corp. 2011, 2012 vii

viii Storwize V7000 Unified: Quick Installation Guide

Safety and environmental notices
Review the multilingual safety notices for the IBM®system before you install and
use the product.
Suitability for telecommunication environment: This product is not intended to
connect directly or indirectly by any means whatsoever to interfaces of public
telecommunications networks.
To find the translated text for a caution or danger notice:
1. Look for the identification number at the end of each caution notice or each
danger notice. In the following examples, the numbers (C001) and (D002) are
the identification numbers.
CAUTION:
A caution notice indicates the presence of a hazard that has the potential of
causing moderate or minor personal injury. (C001)
DANGER
A danger notice indicates the presence of a hazard that has the potential
of causing death or serious personal injury. (D002)
2. Locate IBM Systems Safety Notices with the user publications that were provided
with the Storwize®V7000 Unified hardware.
3. Find the matching identification number in the IBM Systems Safety Notices. Then
review the topics concerning the safety notices to ensure that you are in
compliance.
4. Optionally, read the multilingual safety instructions on the Storwize V7000
Unified website. Go to www.ibm.com/storage/support/storwize/v7000/
unified and click the documentation link.
Safety
Before installing this product, read the Safety Information.
Antes de instalar este produto, leia as Informações de Segurança.
Pred instalací tohoto produktu si prectete prírucku bezpecnostních instrukcí.
© Copyright IBM Corp. 2011, 2012 ix

Læs sikkerhedsforskrifterne, før du installerer dette produkt.
Lees voordat u dit product installeert eerst de veiligheidsvoorschriften.
Ennen kuin asennat tämän tuotteen, lue turvaohjeet kohdasta Safety Information.
Avant d'installer ce produit, lisez les consignes de sécurité.
Vor der Installation dieses Produkts die Sicherheitshinweise lesen.
Prima di installare questo prodotto, leggere le Informazioni sulla Sicurezza.
Les sikkerhetsinformasjonen (Safety Information) før du installerer dette produktet.
Antes de instalar este produto, leia as Informações sobre Segurança.
Antes de instalar este producto, lea la información de seguridad.
Läs säkerhetsinformationen innan du installerar den här produkten.
xStorwize V7000 Unified: Quick Installation Guide

Safety statements
Each caution and danger statement in this document is labeled with a number.
This number is used to cross reference an English-language caution or danger
statement with translated versions of the caution or danger statement in the Safety
Information document. For example, if a caution statement is labeled “Statement 1”,
translations for that caution statement are in the Safety Information document under
“Statement 1.”
Important:
Be sure to read all caution and danger statements in this document before you
perform the procedures. Read any additional safety information that comes with
the system or optional device before you install the device.
Statement 1
DANGER
Electrical current from power, telephone, and communication cables is
hazardous.
To avoid a shock hazard:
vDo not connect or disconnect any cables or perform installation,
maintenance, or reconfiguration of this product during an electrical storm.
vConnect all power cords to a properly wired and grounded electrical outlet.
vConnect to properly wired outlets any equipment that will be attached to
this product.
vWhen possible, use one hand only to connect or disconnect signal cables.
vNever turn on any equipment when there is evidence of fire, water, or
structural damage.
vDisconnect the attached power cords, telecommunications systems,
networks, and modems before you open the device covers, unless
instructed otherwise in the installation and configuration procedures.
vConnect and disconnect cables as described in the following table when
installing, moving, or opening covers on this product or attached devices.
To Connect: To Disconnect:
1. Turn everything OFF.
2. First, attach all cables to devices.
3. Attach signal cables to connectors.
4. Attach power cords to outlet.
5. Turn device ON.
1. Turn everything OFF.
2. First, remove power cords from outlet.
3. Remove signal cables from connectors.
4. Remove all cables from devices.
Safety and environmental notices xi

Statement 2
CAUTION:
When replacing the lithium battery, use only IBM Part Number 33F8354 or an
equivalent type battery recommended by the manufacturer. If your system has a
module containing a lithium battery, replace it only with the same module type
made by the same manufacturer. The battery contains lithium and can explode if
not properly used, handled, or disposed of.
Do not:
vThrow or immerse into water
vHeat to more than 100°C (212°F)
vRepair or disassemble
Dispose of the battery as required by local ordinances or regulations.
Statement 3
CAUTION:
When laser products (such as CD-ROMs, DVD drives, fiber optic devices, or
transmitters) are installed, note the following:
vDo not remove the covers. Removing the covers of the laser product could
result in exposure to hazardous laser radiation. There are no serviceable parts
inside the device.
vUse of controls or adjustments or performance of procedures other than those
specified herein might result in hazardous radiation exposure.
xii Storwize V7000 Unified: Quick Installation Guide

DANGER
Some laser products contain an embedded Class 3A or Class 3B laser diode.
Note the following.
Laser radiation when open. Do not stare into the beam, do not view directly
with optical instruments, and avoid direct exposure to the beam.
Class 1 Laser Product
Laser Klasse 1
Laser Klass 1
Luokan 1 Laserlaite
Appareil A Laser de Classe 1
`
Statement 4
≥18 kg (39.7 lb) ≥32 kg (70.5 lb) ≥55 kg (121.2 lb)
CAUTION:
Use safe practices when lifting.
Statement 5
CAUTION:
The power control button on the device and the power switch on the power
supply do not turn off the electrical current supplied to the device. The device
also might have more than one power cord. To remove all electrical current from
the device, ensure that all power cords are disconnected from the power source.
Safety and environmental notices xiii

1
2
Statement 8
CAUTION:
Never remove the cover on a power supply or any part that has the following
label attached.
Hazardous voltage, current, and energy levels are present inside any component
that has this label attached. There are no serviceable parts inside these
components. If you suspect a problem with one of these parts, contact a service
technician.
Statement 26
CAUTION:
Do not place any object on top of rack-mounted devices.
This node is suitable for use on an IT power-distribution system whose maximum
phase-to-phase voltage is 240 V under any distribution fault condition.
Important: This product is not suitable for use with visual display workplace
devices according to Clause 2 of the German Ordinance for Work with Visual
Display Units.
xiv Storwize V7000 Unified: Quick Installation Guide

Sound pressure
Attention: Depending on local conditions, the sound pressure can exceed 85
dB(A) during service operations. In such cases, wear appropriate hearing
protection.
Safety and environmental notices xv

xvi Storwize V7000 Unified: Quick Installation Guide

About this guide
This guide describes how to install the IBM Storwize V7000 Unified system.
The chapters that follow introduce you to the hardware components and
requirements needed for installing the Storwize V7000 Unified system.
Who should use this guide
This guide is intended for users installing the Storwize V7000 Unified system.
Before configuring your system make sure you follow the procedures as listed. Be
sure to gather IP addresses necessary prior to installation. See “Step 5. Gather
information” on page 11.
Accessibility
IBM has a long-standing commitment to people with disabilities. In keeping with
that commitment to accessibility, IBM strongly supports the U.S. Federal
government's use of accessibility as a criterion in the procurement of Electronic
Information Technology (EIT).
IBM strives to provide products with usable access for everyone, regardless of age
or ability.
This product uses standard Windows navigation keys.
For more information, see “Accessibility features for IBM Storwize V7000 Unified,”
on page 75.
Emphasis
Different typefaces are used in this guide to show emphasis.
The following typefaces are used to show emphasis:
Boldface Text in boldface represents menu items.
Bold monospace Text in bold monospace represents command
names.
Italics Text in italics is used to emphasize a word.
In command syntax, it is used for variables
for which you supply actual values, such as
a default directory or the name of a system.
Monospace Text in monospace identifies the data or
commands that you type, samples of
command output, examples of program code
or messages from the system, or names of
command flags, parameters, arguments, and
name-value pairs.
© Copyright IBM Corp. 2011, 2012 xvii

Storwize V7000 Unified library and related publications
Product manuals, other publications, and websites contain information that relates
to Storwize V7000 Unified.
Storwize V7000 Unified Information Center
The IBM Storwize V7000 Unified Information Center contains all of the
information that is required to install, configure, and manage the Storwize V7000
Unified. The information center is updated between Storwize V7000 Unified
product releases to provide the most current documentation. The information
center is available at the following website:
publib.boulder.ibm.com/infocenter/storwize/unified_ic/index.jsp
Storwize V7000 Unified library
Unless otherwise noted, the publications in the Storwize V7000 Unified library are
available in Adobe portable document format (PDF) from the following website:
www.ibm.com/storage/support/storwize/v7000/unified
Each of the PDF publications in Table 1 is available in this information center by
clicking the number in the “Order number” column:
Table 1. Storwize V7000 Unified library
Title Description Order number
Storwize V7000 Unified Quick
Installation Guide
This guide provides
instructions for unpacking
your shipping order and
installing your system. The
first of three chapters
describes verifying your
order, becoming familiar
with the hardware
components, and meeting
environmental requirements.
The second chapter describes
installing the hardware and
attaching data cables and
power cords. The last
chapter describes accessing
the management GUI to
initially configure your
system.
GA32-1056
Storwize V7000 Unified
Problem Determination Guide
This guide describes how to
service, maintain, and
troubleshoot the Storwize
V7000 Unified system.
GA32-1057
xviii Storwize V7000 Unified: Quick Installation Guide

Table 1. Storwize V7000 Unified library (continued)
Title Description Order number
IBM Systems Safety Notices This guide contains
translated caution and
danger statements for the
node canister documentation.
Each caution and danger
statement in the Storwize
V7000 Unified
documentation has a number
that you can use to locate the
corresponding statement in
your language in the IBM
Systems Safety Notices
document.
G229-9054
Safety Information This guide contains
translated caution and
danger statements for the file
module documentation. Each
caution and danger
statement in the Storwize
V7000 Unified
documentation has a number
that you can use to locate the
corresponding statement in
your language in the Safety
Information document.
P/N 59Y7218
Storwize V7000 Unified Read
First Flyer
This document introduces
the major components of the
Storwize V7000 Unified
system and describes how to
get started with the Storwize
V7000 Unified Quick
Installation Guide.
GA32-1055
IBM Statement of Limited
Warranty (2145 and 2076)
This multilingual document
provides information about
the IBM warranty for
machine types 2145 and
2076.
Part number: 85Y5978
IBM Statement of Limited
Warranty (2073)
This multilingual document
provides information about
the IBM warranty for
machine type 2073.
Part number: 00L4547
IBM License Agreement for
Machine Code
This multilingual guide
contains the License
Agreement for Machine
Code for the Storwize V7000
Unified product.
SC28-6872 (contains
Z125-5468)
Other IBM publications
Table 2 on page xx lists IBM publications that contain information related to the
Storwize V7000 Unified.
About this guide xix

Table 2. Other IBM publications
Title Description Order number
IBM Storage Management
Pack for Microsoft System
Center Operations Manager
User Guide
This guide describes how to
install, configure, and use the
IBM Storage Management Pack
for Microsoft System Center
Operations Manager (SCOM).
GC27-3909
publibfp.dhe.ibm.com/
epubs/pdf/c2739092.pdf
IBM Storage Management
Console for VMware vCenter,
version 3.0.0, User Guide
This publication describes how to
install, configure, and use the
IBM Storage Management
Console for VMware vCenter,
which enables Storwize V7000
Unified and other IBM storage
systems to be integrated in
VMware vCenter environments.
GA32-0929
publibfp.dhe.ibm.com/
epubs/pdf/a3209295.pdf
IBM documentation and related websites
Table 3 lists websites that provide publications and other information about the
Storwize V7000 Unified or related products or technologies.
Table 3. IBM documentation and related websites
Website Address
Support for Storwize V7000 Unified
(2073)
www.ibm.com/storage/support/storwize/v7000/
unified
Support for IBM System Storage®
and IBM TotalStorage products
www.ibm.com/storage/support/
IBM Publications Center www.ibm.com/e-business/linkweb/publications/
servlet/pbi.wss
IBM Redbooks®publications www.redbooks.ibm.com/
Related accessibility information
To view a PDF file, you need Adobe Acrobat Reader, which can be downloaded
from the Adobe website:
www.adobe.com/support/downloads/main.html
How to order IBM publications
The IBM Publications Center is a worldwide central repository for IBM product
publications and marketing material.
The IBM Publications Center offers customized search functions to help you find
the publications that you need. Some publications are available for you to view or
download at no charge. You can also order publications. The publications center
displays prices in your local currency. You can access the IBM Publications Center
through the following website:
www.ibm.com/e-business/linkweb/publications/servlet/pbi.wss
xx Storwize V7000 Unified: Quick Installation Guide