Reece ISSY Z8 BUTTERFLY TALL BOY Quick start guide

To see the complete ISSY range go to
www.reece.com.au/bathrooms
Pony Oak Hazelnut Oak
ISSY //
Z8 BUTTERFLY TALL BOY
Disclaimer: Products in this specication manual must by regulation be installed by licensed and registered trade people.
The manufacturer/distributor reserves the right to vary specications or delete models from their range without prior
notication. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication
however the manufacturer/distributor takes no responsibility for printing errors.
Tech Page Version 2
Named for its signature Zuster-designed“Buttery” handle, ISSY Z8 Buttery pays homage to craftsmanship and bespoke design with a
series of cleverly integrated luxuries. The ISSY Z8 Buttery Tall Boy features secret side drawers and an integrated laundry basket (optional)
to keep your bathroom beautiful. The Z8 Buttery Tall Boy can also be customised, allowing you to achieve your ultimate designer look.
Designed and Manufactured in Australia
CLEANING RECOMMENDATIONS
Your timber frame should be cleaned with a mild, non acidic, non abrasive detergent and soft cloth . Finish by cleaning o detergents
with a soft damp cloth and towel dry. Always clean spills and water immediately.
Damage caused by any improper treatement is not covered by the product warranty. Refer to Warranty Conditions.
SPECIFICATIONS
Recommended use Domestic, Commercial & Hotel
Materials American Oak Veneer Carcass
Solid American Oak Framing Detail
Mirror - 4mm Australian Made Safety Mirror
Drawer Inlay - Quilted Vinyl
Timber Colours American Oak, Charcoal Oak, Pony Oak , Hazelnut Oak.
Fixing Freestanding/ Optional Fixing
Features Secret Makeup Drawers, Removable Laundry Basket
Fixing Bolted / Screwed to Wall by a Licensed Trades Person
STANDARD SIZES TALL450 TALL450
Width (mm) 450 450
Depth (mm) 470 470
Height (mm) 1800 2050
CUSTOM SIZES TALL450 TALL450
Width (mm) 450-550 450-550
Depth (mm) 470 470
Height (mm) 1800-2000 2001-2100
page 1 of 8

ISSY //
Z8 BUTTERFLY TALLBOY
COLOUR OPTIONS
AMERICAN OAK
CHARCOAL OAK
PONY OAK
HAZELNUT OAK
Plumbers, please ensure a copy of the installation instructions is left
with the end user for future reference
TIMBER OPTIONS
page 2 of 8

STANDARD SIZES
ISSY //
Z8 BUTTERFLY TALLBOY
450 X 470 X 1800
450 X 470 X 2050
page 3 of 8

ISSY //
Z8 BUTTERFLY TALLBOY
CUSTOM SIZES
450550 X 470 X 18002000
450550 X 470 X 20012100
page 4 of 8

ISSY //
Z8 BUTTERFLY TALLBOY
INSTALLATION INSTRUCTIONS
Vanity should be installed by a qualied, licensed trades person.
• Prior to installation it is important to inspect the vanity to ensure no damage has occurred in transit. If damage has occurred, or a vis-
ible defect exists, do not proceed with installation and advise supplier immediately. No warranty claim for damage will be accepted
if the vanity is installed.
• It is recommended that the Vanity Top is protected during installation
Vanity Fitting Instructions.
Please Note: Manufacturer will not be liable for the cost of installation or removal of the vanity and the warranty will be voided if
damage occurred during or after installation.
1. To aid Installation, label and remove door fronts and drawers. To remove draws: pull out draws to full extent, on the underside you
will nd 2 clamp-release clips. Press both of these simultaneously so they clip and lift up and out. The draws should easily remove
from the runners. Store them in a safe place where they will not get damaged.
2. Check that the unit will t into the location. On timber walls, mark the positions of the studs, so to be able to x the unit to these
later.
3. Ensure the storage unit is installed at the correct distance, so that when the vanity goes into position, It aligns with the waste pipe.
4. Determine the distance of the waste pipe in relation to its position in the vanity unit on the wall. Based on the total width of the
vanity, and the position of the waste pipe cut out in its top, you will need to start installing the Tall Storage unit on the right hand
side, where you have marked out where the vanity will nish.
1. Locate the stud (you can screw through any part of the back
of the unit) into the stud.
2. Drill holes and lightly countersink your screw hole to ensure
a neat nish. (If it is a brick wall, you will need to use the
appropriate masonry drill bits as well as a hammer drill. A
toggle type system is also required (xings not supplied)
3. Fix your unit to the wall.
4. Corian Support (4B) (Included with Z8 Extended Top Vanity)
- If not already Installed, Identify which side will be adjoining
with the Corian and x into pre-drilled holes.
Installing the Tall Storage Unit
4B
page 5 of 8

ISSY //
Z8 BUTTERFLY TALLBOY
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
Note: It is recommended that you use an Installation stand
(Not included) to assist the installation of this Shaving
Cabinet. This unit being level is imperative to the
Overall installation.
1. Ensure you measure correctly so that the top of the shaving cabinet
aligns ush with the top of the Tall Storage Unit. DETAIL: A
2. You can drill through any part of the back of the unit into the wall.
Ensure you have at least 4 points of contact to studs. These screws
can be hidden with the timber plugs included.
3. If required, you can also x the Shaving Cabinet to the Tall Storage
Unit internally (again neatly drill and countersink holes before
screwing together)
Installing the Shaving Cabinet
Note: It is recommended the gap between vanity and shaving cabinet is
measured at both ends to ensure level installation.
ENSURING SCREWS ARE FIXED TO STUDS Please x Vanity Unit to studs at 4
point (minimum) for a 1000mm vanity, and 6 points for a 1500mm vanity.
1. The unit needs to be placed to line up with the plumbing system/ and
the units above and below. Standard mounting height is 760mm from
the ground to the top of the Corian.
2. You can drill through any part of the back of the unit into the wall.
Ensure you have at least 4 points of contact to studs.
Installing the Vanity
Re-attaching the Drawers
1. Fully extend the drawer runner and place drawers on the guides
2. When pushed closed these should click together and run smoothly. If
the drawers do not click together or don’t run freely, remove and repeat
the step.
INSTALLATION INSTRUCTIONS
DETAIL: A
page 6 of 8

Tall Boy Fitting Instructions
• Prior to installation it is important to inspect the Z8 Tall Boy to ensure no damage has occurred in transit. If damage has occurred, or a
visible defect exists, DO NOT proceed with installation and advise supplier immediately. No warranty claim for damage will be accepted
if the Cabinet is installed. This includes scratches to the glass.
• It is recommended that the mirror is protected during installation.
Please Note:Manufacturer will not be liable for the cost of installation or removal of the mirror and the warranty will be voided if
damage occurred during or after installation.
• If installing in combination with other ISSY by Zuster units, Install the Z8 Tall boy rst.
• Attach corian support where the corian will rest if installing with an extended top vanity.
(Recommended vanity height 760mm)
• This unit is freestanding, however it is STRONGLY RECOMENDED to be xed to the wall for safety. To do
this, screw through any part of the back of the unit into the wall, ensuring contact to studs. If not xing
to studded wall, installer must ensure appropriate xing to provide sucient support.
INSTALLATION INSTRUCTIONS
Tall Boy should be installed by a qualied, licensed trades person.
ISSY //
Z8 BUTTERFLY TALLBOY
page 7 of 8

INSTALLATION INSTRUCTIONS
ISSY //
Z8 BUTTERFLY TALLBOY
REMOVE DOOR
1. Remove door soft close mechanism
HEIGHT ADJUSTMENT
1. Turn left to right for up and down doors
2. Unclip hinge from cabinet releasing clip
LEFT TO RIGHT SIDE ADJUSTMENT
1. Turn left to right for side adjustment 2. Turn Left/Right for depth adjustment
page 8 of 8