Reece Milli Series User manual

PURE DIVERTER SYSTEM
page 1 of 4
To see the complete MILLI range go to
www.reece.com.au/bathrooms
SPECIFICATIONS
Recommended Use Domestic, Hotel and Commercial
Finish
Material
Chrome, Matt Black, Rose Gold,
Brushed Gunmetal
Brass
Pressure Rating Recommended working pressure 300 - 500Kpa
Temperature Rating Max continuous working temperature
65 deg. C
Suitable Hot Water Units Storage Tank: Yes
Continuous Flow: Yes
Gravity Feed: Not recommended
CLEANING RECOMMENDATIONS
We recommend the use of soapy water or approved cleaners.
This product should not be cleaned with abrasive materials.
Damage caused by any improper treatment is not covered by the product warranty. Refer to Warranty Conditions.
Disclaimer: Products in this specication manual must by regulation be installed by licensed and
registered trade people. The manufacturer/distributor reserves the right to vary specications or
delete models from their range without prior notication. Dimensions are nominal measurements
only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/
distributor takes no responsibility for printing errors.
Tech Page Version 1
AS/NZS 3718
LIC. 20081
Dimensions are nominal measurements only.
100
54
28
62
Diverter Mixer
page 1 of 4

PURE DIVERTER SYSTEM
page 2 of 4
Matte Black
Brushed Gunmetal
Rose Gold
Don’t risk it, use a licensed plumber.TM

PURE DIVERTER SYSTEM
page 3 of 4
Masterfit
NOGGING
28-32
Wall Covering
Max. 25mm
View from above
90
Stud face
Pipe Connections
This
side
UP
Handle
Body
Cover
Flange
Hot
Cold
Outlet 1
Outlet 2
DIVERTER
PROGRESSIVE
MIXER
DIVERTER
PROGRESSIVE
MIXER
INSTALLATION INSTRUCTIONS
Tapware is to be installed by a Licensed Plumber in
accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa.
Maximum water temperature is 65 deg.c.
ROUGH IN PLUMBING
- Prior to installing, calculate the nished wall thickness to ensure enough adjustment is available when tting the Handle.
- The Mixer is supplied with a plastic cover to protect the Mixer during Plastering and Tiling.
- The “Mixed In” and Outlet Ports are marked on the shoulder of the Mastert body to indicate the correct conncection.
Note: Do not cross Hot/Cold connects from Mixer 1 to Mixer 2 (See Pipe Connections).
- Set a Nogging between 28 - 32mm back from the face of the wall stud. (see Fig. 1).
- Using the screws provided, x the Mixer to the Nogging.
- Ensure the Mixer is aligned square and well secured.
- Flush all water feed lines. Pipes and ttings must be free from any dirt and debris before connecting to the Mixer.
- Once all water ttings are connected, check Hot/Cold water ow by operating the Mixer.
- Check for any water leaks.
- Once all checks have been made, leave the Mixer in the closed position and replace the protective cover.
- Store remaining parts in a safe place until wall coverings have been completed and nal t-o is required (see Dress nishing)
PLUMBER NOTE:
- On-site high pressure line testing must be conducted with the Mixer in the closed position. (STATIC TEST ONLY )
- Under no circumstances is the Mixer to be opened when exceeding the maximum stated water pressure.
- At the completion of the testing, do not relieve any high pressure by opening the Mixer.
- Exposing the internals of the Mixer Cartridge to higher than specied water pressures, will void the manufacturer’s warranty.

PURE DIVERTER SYSTEM
page 4 of 4
INSTALLATION INSTRUCTIONS
Plumbers, please ensure a copy of the installation
instructions is left with the end user for future reference
Tapware is to be installed by a Licensed Plumber in
accordance with AS/NZS 3500:2003
Recommended working water pressure 300-500 kpa.
Maximum water temperature is 65 deg.c.
DRESS FINISHING AND HANDLE ADJUSTMENT
- Prior to t o ensure the correct size cut out around the Mixers (100mm centres) has been achieved.(see Fig.1)
- Remove the protective Cover from the Diverter. Ensure the Oring is intact and the installation is clean and free from any debri.
- Apply sealant to the outside of the Cover Flange and t to the Diverter.
- Fit the Handles onto the Adjustment Fitting.
- If adjustment is required, remove the Handles and loosen the Set Screws of the Adjustment Fitting.
- Wind the Adjustment Fitting to reduce or increase the gap between the Wall and the Handle. (see Fig.2)
NOTE: Extensions may be acquired if correct installation can not be achieved.(Contact manufacturer)
- Once the gap from the Wall to the Handle is between 2-3mm, remove the Handle and tighten the Set Screws of the Adjustment Fitting.
- When securing the Handle adjustment Fitting, ensure the Set Screws are tightened onto the ats of the Cartridge Extension. (see Fig.2)
- Do not tighten the Set Screws on the threads of the Cartridge Extension.
- Fit the Handle so the Set Screw is positioned at the bottom. (tighten well)
- Note the Set screw must engage in the grove of the Adjustment Fitting.
Combined wall
thickness
not to exceed 25mm
NOGGING
Wall
Stud
Hot
Set Screw
28-32mm
Set Screws must
be tightened onto
the Flats of the
Cartridge extension
Cartridge
Extension
Wall cut out
47 - 52mm
Round
FRONT FACE
OF
WALL STUD
Apply
Sealant
Handle
Body
Cover
Flange
Set
Screw
Handle
Adjustment
Fitting
Finished
wall
surface
Cartridge
Extension
Set Screw Flat
Handle
Adjustment
Fitting
Fig.1
Fig.2
FIT OFF
ORING
page 4 of 4