Reechcraft Bronco User manual

THE ALL-TERRAIN SCAFFOLD
USER MANUAL

CONTENTS
WARNING! FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH. INSPECTION: Inspect
ReechCraftTM BroncoTM for damage before each use. Never use the Bronco if parts are missing, cracked, bent or after being exposed to high
heat or any corrosive agent. Label the Bronco: “Dangerous - Do Not Use” and discard, or call manufacturer. Handle all Bronco units with
care. SET-UP AND USE: Do not exceed the duty rating of this unit. The maximum safe weight load for each Bronco is 300 pounds or 600 pounds
per pair. Over loading could cause serious injury or death. Place the Bronco on a firm surface where the footing is solid, rigid and capable of
carrying the maximum intended load without slipping. Do not place the Bronco on loose gravel, ice, snow, mud, leaves or other soft or slippery
surfaces. When using the Bronco on any other surface than the ground, be sure it is properly secured to avoid slipping. Do not place boxes,
ladders or other scaffolding on top of the plank to gain additional height. The Bronco IS NOT a ladder and should not be used independent of
a rated plank or stage. Be sure all locking devices are secure. Do not use the Bronco beyond a plank height of 6 feet off the ground. Adjust
the Bronco so that the plank or stage is level. Be sure the plank or stage is supported a minimum of 12 to 18 inches on each end. Never set the
Bronco in front of locked doors or in other locations where the units could be bumped or kicked. Barricades must be used where necessary.
Do not apply side loads to the Bronco unit or plank. Never push or pull anything while working on Bronco units. Do not use the Bronco unit
without an appropriately rated scaffold plank. DANGER! Aluminum conducts electricity! Keep Broncos away from uninsulated electrical
circuits an wires. Use extreme caution when working near electrical wires.Failure to comply may result in injury or death. Maximum platform
height: 6 feet. SECURELY ENGAGE BRONCOTM LOCKS BEFORE CLIMBING. Be sure to use fall restraint devises as prescribed by local, State
and Federal requirements. Failure to comply with all local, State and Federal requirements may result in serious injury or death. Never drop or
apply an impact load to the Bronco. Do not use the Bronco if you are not in good physical condition or are under the influence of any substance
(including prescription medicine) that may impair your ability to use the Bronco properly and safely. Do not leave the Bronco setup when
unattended. Do not use in high winds. Keep you body centered on the work platform. Do not overreach. Never hoist anything from the scaffold.
Do not bounce or run on the scaffold. Keep your Bronco Clean and free of all foreign material. Do not store any material on the Bronco System
Your Bronco units should be properly secured during transport. Always store in a clean, dry place. WARNING: Only Bronco accessories shall be
used, and must be installed in accordance with the manufacturers recommended procedure. This product MEETS OR EXCEEDS ESTABLISHED
OSHA REQUIREMENTS.
Please follow these proper setup
procedures as indicated within this
manual.
02
Setup.........................................................................3
Configuration...........................................................4
Warranty..................................................................5

QUICK SETUP
Unfold the Bronco by
pulling out the rear leg
and pressing down on
the spreader to lock
the leg into position.
03
Push down on the
locking pin, rotate the
bottom of the leg and
extend to the desired
length. Be sure the
locking pin is fully
engaged.
To ensure proper
setup, consult the rear
leg diagram.
1
2
3

CONFIGURATION
04
WEIGHT DISTRIBUTION
Note the label on the back
leg and ensure that the
horizontal line is parallel to
the ground and the vertical
line is plumb.
PLANK CONFIGURATION
Ensure that the Bronco is
angled like the diagram
to the right for easy plank
access and proper weight
distribution.

WARRANTY
LIMITED 1-YEAR WARRANTY
ReechCraft warrants this product to the original purchaser for a period of one (1) years against deficiencies
in material and workmanship. This LIMITED WARRANTY does not cover products that are improperly used,
abused, altered or repaired. Deficient products will be replaced or repaired. Please call 1-888-600-6160
for more information or return instructions. THIS LIMITED WARRANTY IS GIVEN IN LIEU OF ALL OTHERS
INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
AND EXCLUDES ALL INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on
how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so
these limitations may not apply to you. This LIMITED WARRANTY gives you specific legal rights that may vary
from state to state.
05