Reed Instruments R7920 User manual

Instruction
Manual
R7920
W
A
R
R
A
N
T
Y
W
A
R
R
A
N
T
Y
1 YEAR
1 AN
G
A
R
A
N
T
I
E
G
A
R
A
N
T
I
E
W
A
R
R
A
N
T
Y
W
A
R
R
A
N
T
Y
G
A
R
A
N
T
I
E
G
A
R
A
N
T
I
E
W
A
R
R
A
N
T
Y
W
A
R
R
A
N
T
Y
G
A
R
A
N
T
I
E
G
A
R
A
N
T
I
E
White background
Transparentbackground
White
Black
1 YEAR1AN
Ultrasonic
Thickness
Gauge
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

2
Table of Contents
Introduction ................................................................................................ 4
Product Quality........................................................................................... 4
Safety ......................................................................................................... 4
Features...................................................................................................... 5
Included...................................................................................................... 5
Specications............................................................................................. 6
Instrument Description............................................................................... 7
Display Description .................................................................................... 7
Operating Instructions...........................................................................8-12
Initial Calibration .................................................................................... 8
Selecting the Material Sound Velocity ................................................... 9
Preparing the Measurement Surface ..................................................... 9
Taking Thickness Measurements ......................................................... 10
Measurement Methods...................................................................10-11
Determining the Sound Velocity for a Material
with a Known Thickness....................................................................... 11
Auto Power OFF .................................................................................. 11
Enabling/Disabling Alarm Setting......................................................... 12
Data Storage ........................................................................................ 12
Clearing Measurements Results .......................................................... 12
Setup Mode.........................................................................................13-18
Select the Material under Test ............................................................. 13
Adjusting the Sound Velocity of the Material under Test ..................... 14
Select Unit of Measure (in/mm)............................................................ 14
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

3
View/Delete Stored Data...................................................................... 14
View from First/Last Page ................................................................ 15
View from Selected Item .................................................................. 15
Delete by Group Range (Delete the Item)......................................... 16
Delete All .......................................................................................... 16
System Settings................................................................................... 16
Enable or Disable the Audible Beep (Sound) ................................... 17
Setting the Backlight Timer .............................................................. 17
Setting the Auto Power OFF Timer .................................................. 17
Setting Alarm Thickness Limits ........................................................ 17
View Device Information ...................................................................... 18
System Reset....................................................................................... 18
Maintenance............................................................................................. 18
Cleaning the Test Piece ....................................................................... 18
Protecting the Ultrasonic Sensor......................................................... 18
Replacing the Ultrasonic Sensor.......................................................... 18
Charging the Battery ................................................................................ 19
Applications.............................................................................................. 19
Accessories and Replacement Parts ....................................................... 19
Product Care ............................................................................................ 19
Appendix A..........................................................................................20-25
Material Sound Velocities Table ......................................................20-21
Measurements on Cylindrical Surfaces................................................ 21
Measuring Compound Profiles ............................................................ 21
Measuring an Un-Parallel Surface........................................................ 22
Influence of Material's Temperature..................................................... 22
Material with Large Attenuation ........................................................... 22
Measuring Castings ........................................................................22-23
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

4
Preventing Errors ............................................................................23-25
Reference Test Pieces.................................................................23-24
Ultra-Thin Material............................................................................ 24
Rust, Corrosion, and Pits ................................................................. 24
Error in Identifying Material............................................................... 24
Degradation of Probe ....................................................................... 24
Overlapped Material and Compound Material ................................. 25
Influence of Metal Surface Oxidation ............................................... 25
Abnormal Readout of Thickness ...................................................... 25
Utilization and Selection of a Coupling Gel (R7950)......................... 25
Product Warranty ..................................................................................... 26
Product Disposal and Recycling .............................................................. 26
Product Support....................................................................................... 26
Introduction
Thank you for purchasing your REED R7920 Ultrasonic Thickness Gauge.
Please read the following instructions carefully before using your instrument.
By following the steps outlined in this manual your meter will provide years
of reliable service.
Product Quality
This product has been manufactured in an ISO9001 facility and has been
calibrated during the manufacturing process to meet stated product
specications. If a certicate of calibration is required, please contact the
nearest authorized REED distributor or authorized Service Center. Please
note an additional fee for this service will apply.
Safety
Never attempt to repair or modify your instrument. Dismantling your
product, other than for the purpose of replacing batteries, may cause
damage that will not be covered under the manufacturer's warranty.
Servicing should only be provided by an authorized service center.
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

5
Features
• Measures the thickness of steel, cast iron, aluminum, acrylic resin, red
copper, brass, zinc, quartz glass, polyethylene, PVC, grey cast iron and
nodular cast iron
• Easy-to-read backlit LCD display
• User selectable unit of measure (in/mm)
• Internal memory stores up to 300 measurements
• Displays sound velocity at the touch of a button
• User adjustable High/Low alarms
• Automatic material calibration
• Auto shut off and low battery indicator
Included
• Ultrasonic Thickness Gauge
• Ultrasonic Couplant Gel
• Probe
• USB Cable
• Carrying Case
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

6
Specifications
Measuring Range: 0.04 to 11.8" (1.00 to 300mm)
Accuracy: <10mm: ±0.1mm
≥10mm: ±(1% rdg. +0.1mm)
Resolution: 0.1mm/0.01mm/0.01"
Velocity Range: 1000 to 9999m/s
(0.039 to 0.394in/µs)
Compatible Materials: Steel, cast iron, aluminum, acrylic
resin, red copper, brass, zinc, quartz
glass, polyethylene, PVC, grey cast
iron and nodular cast iron
Display: 2.4" monochrome dot matrix screen
Backlight: Yes
Probe Length: 3' (91cm)
Probe Diameter: 0.5" (12.7mm)
Internal Memory: Yes (up to 300 readings)
Low Battery Indicator: Yes
Power Supply: Built-in lithium battery
(3.7V 2000mAh)
Battery Life: Approx. 16 hours (Fully Charged)
Product Certications: CE
Operating Temperature: 32 to 104°F (0 to 40°C)
Probe Operating Temperature: 32 to 104°F (0 to 40°C)
Operating Humidity Range: 20 to 80%
Storage Temperature: 14 to 122°F (-10 to 50°C)
Storage Humidity Range: 20 to 70%
Dimensions: 5.5 x 2.6 x 1.12" (140 x 66 x 28.5mm)
Weight: 6.17oz (175g)
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

7
Instrument Description
1. Probe Connectors
2. LCD Display
3. Measurement Mode/
Menu Button
4. Record/Enter Button
5. Back/Alarm Toggle Button
6. Calibration Test Block
7. Power Button
8. Down Arrow
9. Up Arrow
10. Sound Velocity/
Calibration Button
11. Ultrasonic Sensor
Display Description
1. Coupling Indicator
2. Measurement Mode
Indicator
3. Beep Status Indicator
4. Battery Indicator
5. Unit of Measure
6. Measurement/Sound
Velocity Values
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

8
Operating Instructions
1. Insert the ultrasonic sensor into the probe connector sockets
on the meter.
2. Press the POWER button to turn the meter ON. Press and hold the
POWER button for approx. 2 seconds to turn the meter OFF.
3. The LCD will display the current set sound velocity.
Initial Calibration
1. Select Single measurement mode by pressing the
MODE/MENU button.
2. Place a small drop of coupling gel (R7950) on the 4mm calibration
test block.
3. Press and hold the m/s/Cal button to enter calibration mode as
conrmed by "Please Calibrate" on LCD display.
4. Place the sensor on the calibration test block while ensuring the
coupling indicator appears on the display.
5. While continuing to hold the sensor on the calibration test block,
press the REC/ENTER button when the reading has stabilized.
6. Depending on the selected unit of measure, either "0.16in"
(or "4.0/4.00mm") and "nished!" will appear on the LCD display.
7. Calibration is now complete and the ultrasonic sensor can now be
removed from the calibration test block.
Note: Results from the calibration procedure will automatically save
in the meter. It is not necessary to calibrate the meter each time the
unit is powered on unless measurements appear to be inaccurate. The
calibration procedure conrms both the meter and ultrasonic sensor are
functioning properly.
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

9
Selecting the Material Sound Velocity
1. While the meter is on, press the m/s/CAL button to enter the
pre-loaded material sound velocities menu.
2. Press the and buttons to scroll through the
pre-loaded material list.
3. Press the REC/ENTER button to conrm the
material selection and press the and buttons
to adjust the sound velocity of the material under
test if required.
Note: Each material has an adjustment velocity range
as shown below.
4. Press the REC/ENTER button again to conrm selection and resume
normal operation.
Preparing the Measurement Surface
1. Clean dust, dirt or rust off the object, and remove any coatings
(i.e. paint).
2. Smooth the surface of the object by grinding or polishing,
alternatively, coupling gel with a high viscosity can also be used.
Important Note: In any ultrasonic measurement scenario, the shape and
roughness of the desired test material are of great importance. Rough,
uneven surfaces will prevent the ultrasonic sensor from seating properly
against the surface, thus limiting the penetration of ultrasound through the
material, resulting in unstable and therefore, unreliable measurements.
continued...
SPD
5920m/s
5720- 6120
Adjustrange 90º
Figure1 Figure2
Figure3
≤5mm
SPD
5920m/s
5720 - 6120
Adjust range
90º
Figure 1 Figure 2
Figure 3
≤5mm
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

10
Taking Thickness Measurements
1. Set the sound velocity on the meter (See the Selecting the Material
Sound Velocity section for details).
2. Press the MODE/MENU button to select between Single and
Continuous (Scan) measurement mode (See the Measurement
Methods section for details).
3. Apply coupling gel on the material under test and place the sensor
rmly against the desired measurement area.
Note: For most applications a single droplet of coupling gel is sufcient.
4. Verify that the coupling indicator appears on the LCD display.
5. Read the measurement on the LCD display.
6. When the ultrasonic sensor is removed the value will stay on the LCD
and the coupling indicator will disappear.
7. Press and hold the REC/ENTER button to save the measurement
if applicable.
Note: If the coupling indicator does not appear on the display, or
the measured values appear to be erratic, verify that there is an
adequate amount of coupling gel in between the ultrasonic sensor
and the material under test. It is important that the ultrasonic
sensor sits flat against the material.
Measurement Methods
There are four base measurement methods:
1. Single measurement method: This method involves measuring the
thickness at a single point.
2. Double measurement method: This method involves performing
two thickness measurements near a single spot
rotating the ultrasonic sensor from 0° to 90°
with respect to the split face (Figure 1). Take
the smaller of the two indicated values as the
thickness of the material.
continued...
SPD
5920m/s
5720 - 6120
Adjust range
90º
Figure 1 Figure 2
Figure 3
≤5mm
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

11
3. Multi-point measurement: This
method involves performing a number of
measurements within a circle having a
maximum diameter of about 1.18" (30mm)
(Figure 2). Take the minimum indicated
value as the thickness of the material.
4. Continuous measurement (scan):
Continuous measurement method involves
taking continuous measurements along
a specied line according to the single
measurement method, at intervals of 5mm
or less (Figure 3). Take the minimum indicated
value as the thickness of the material.
Determining the Sound Velocity for a Material with a
Known Thickness
The sound velocity of a material can be measured using a test piece with
a known thickness. Select a test piece with a minimum wall thickness
of 20.0mm.
1. Measure the test piece with a caliper or micrometer to
conrm thickness.
2. Apply coupling gel on the material, place the sensor rmly against
the desired measurement area.
3. Remove the ultrasonic sensor from the measurement area and adjust
the measuring display until the actual thickness is met by pressing
the and buttons and press the REC/ENTER button to
conrm selection.
4. The LCD will now display the sound velocity of the test piece.
5. Press the REC/ENTER button to save the sound velocity.
6. At this point, the correct thickness measurement can be achieved by
measuring the same material with the saved sound velocity.
Auto Power OFF
To preserve battery life, the meter is programmed to turn itself OFF after
approximately 5 minutes of inactivity. To adjust the auto power off time,
see the Setting the Auto Power OFF Timer section for details.
continued...
SPD
5920m/s
5720 - 6120
Adjust range
90º
Figure 1 Figure 2
Figure 3
≤5mm
SPD
5920m/s
5720 - 6120
Adjust range
90º
Figure 1 Figure 2
Figure 3
≤5mm
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

12
Enabling/Disabling Alarm Setting
The R7920 will alarm when the measured value is beyond the pre-set
limits. When the measurement is lower or higher than the pre-set standard
value limit, the alarm will sound. To enter the alarm limits, see the Setting
the Alarm Thickness Limits section for details.
Press and hold the BACK/ALARM button to turn the alarm function
ON ( ) or OFF ( ).
Data Storage
When taking a measurement in single or continuous mode, press the
REC/ENTER button to save the measurement if applicable.
Note: Each data record includes the current measurement,
MAX, MIN, AVG values and material sound velocity. A maximum
of 300 groups of data can be stored. While in the continuous
measurement mode, the data can only be saved after the probe is
removed from the test piece.
Clearing Measurements Results
When taking a measurement in single or continuous mode, press the
BACK/ALARM button to clear the current measurements.
Note: Each data record includes the current measurement,
MAX, MIN, AVG values and material sound velocity. While in the
continuous measurement mode, the measurements can only be
cleared after the probe is removed from the test piece.
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

13
Setup Mode
1. Press and hold the MODE/MENU button for 2 seconds to enter
Setup Mode.
2. Use the and arrows to scroll through the following parameters:
Parameter Description
Material Select the Material Under Test
Speed Adjust Sound Velocity of the Material Under Test
Unit Select Unit of Measure
Records View/Delete Stored Data
Setting Access Settings Menu
About View Device Information
Reset Reset to Factory Settings
3. Once the appropriate parameter has been selected, follow the
instructions below.
Select the Material under Test
1. Press the REC/ENTER button when "Material" appears on the LCD.
2. Press the and buttons to scroll through the list of
pre-loaded materials.
3. Press the REC/ENTER button to conrm selection and return to the
Setup Menu screen.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

14
Adjusting the Sound Velocity of the Material under Test
1. Press the REC/ENTER button when "Speed" appears on the LCD.
2. Press the and buttons to adjust the sound velocity of the
material under test if required.
Note: Each material has an adjustment velocity range
as shown below.
3. Press the REC/ENTER button to conrm selection
and return to the Setup Menu screen.
Note: At any time, press the BACK/ALARM button
while in the setup menu screen to exit the Setup mode
and resume normal operation.
Select Unit of Measure (in/mm)
1. Press the REC/ENTER button when "Unit" appears on the LCD.
2. Press the and buttons to select from 0.01in, 0.01mm and 0.1m
units of measure.
3. Press the REC/ENTER button while in the setup menu screen to exit
the Setup mode and resume normal operation.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
View/Delete Stored Data
1. Press the REC/ENTER button when "Records" appears on the LCD.
2. Press the and buttons to scroll through the following
parameters within the stored data function:
a) First Page
b) Last Page
c) Selected Item
d) Delete the Item
e) Delete All
Follow the instructions below to adjust each setting.
Note: If there is no data in the memory, the meter will display
"No Records" and return to the menu screen.
SPD
5920m/s
5720 - 6120
Adjust range
90º
Figure 1 Figure 2
Figure 3
≤5mm
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

15
View from First/Last Page
1. Press the REC/ENTER button to enter the selected parameter.
2. Press the REC/ENTER button again to activate les to view.
3. Press the and buttons to scroll through the list of saved les.
4. Press the REC/ENTER button to see the details of the
measured data.
5. While in the selected measurement data screen, press
the and buttons to scroll through the measurement data
screens for the other saved les.
6. Press the BACK/ALARM button three times to return to the stored
data parameters screen.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
View from Selected Item
1. Press the REC/ENTER button to enter the selected parameter.
2. Press the REC/ENTER button again to skip to the required digit.
3. Press the and buttons until the desired value is reached.
4. Press the REC/ENTER button to conrm and skip to the next digit.
5. After each value has been selected and conrmed, the meter will
automatically search for the data les matching the search criteria.
6. Press the REC/ENTER button again to activate les to view.
7. Press the and buttons to scroll through the list of saved les.
8. Press the REC/ENTER button to see the details of the
measurement data.
9. While in the selected measurement data screen, press
the and buttons to scroll through the measurement data
screens for the other saved les.
10. Press the BACK/ALARM button three times to return to the stored
data parameters screen.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

16
Delete by Group Range (Delete the Item)
1. Press the REC/ENTER button to enter the selected parameter.
2. Press the REC/ENTER button again to skip to the required digit.
3. Press the and buttons until the desired value is reached.
4. Press the REC/ENTER button to conrm and skip to the next digit.
5. After each value has been selected and conrmed, the meter will ask
to conrm deletion of the specic group range.
6. Press the and buttons to select between "Yes" and "No".
7. Press the REC/ENTER button to conrm selection.
8. Press the BACK/ALARM button to return to the stored data
parameters screen.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
Delete All
1. Press the REC/ENTER button to enter the selected parameter.
2. Press the and buttons to select between "Yes" and "No".
3. Press the REC/ENTER button to conrm selection.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
System Settings
1. Press the REC/ENTER button when "Settings" appears on the LCD.
2. Press the and buttons to scroll through the following
parameters within the system settings function:
a) Sound
b) Backlight
c) Power OFF
d) Alarm
Follow the instructions below to adjust each setting.
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

17
Enable or Disable the Audible Beep (Sound)
1. Press the REC/ENTER button when "Sound" appears on the LCD.
2. Press the and buttons to select between "Yes" and "No".
3. Press the REC/ENTER button to conrm selection.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
Setting the Backlight Timer
1. Press the REC/ENTER button when "Back light" appears
on the LCD.
2. Press the and buttons to set the backlight timer between
60-180 seconds.
3. Press the REC/ENTER button to conrm selection.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
Setting the Auto Power OFF Timer
1. Press the REC/ENTER button when "Power off" appears
on the LCD.
2. Press the and buttons to set the backlight timer between
120-300 seconds.
3. Press the REC/ENTER button to conrm selection.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
Setting Alarm Thickness Limits
1. Press the REC/ENTER button when "Alarm" appears on the LCD.
2. Press the and buttons to set the standard thickness value.
3. Press the REC/ENTER button to conrm selection and to set the
allowable thickness limit.
4. Press the and buttons to set the thickness limit value.
5. Press the REC/ENTER button to conrm selection.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

18
View Device Information
1. Press the REC/ENTER button when "About" appears on the LCD to
view the device information.
2. Press the BACK/ALARM button to return to the Setup Menu screen.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
System Reset
1. Press the REC/ENTER button when "Reset" appears on the LCD.
2. Press the and buttons to select between "Yes" or "No".
3. Press the REC/ENTER button to conrm selection.
Note: At any time, press the BACK/ALARM button while in the setup
menu screen to exit the Setup mode and resume normal operation.
Maintenance
Cleaning the Test Piece
After taking a measurement, clean the test pieces to prevent them from
rusting. If the pieces are not to be used for a long period of time, coat
them with oil to prevent rust.
Protecting the Ultrasonic Sensor
Be sure to clean the ultrasonic sensor and cable after each use. Grease,
oil and dust will cause the cable to dry out and shorten life expectancy.
The temperature of the surface being measured should not
exceed 140°F (60°C).
Replacing the Ultrasonic Sensor
The degradation and wear of the probe's interlayer plate will inuence
measurements. Replace the probe when the following occurs:
• The same value is always displayed when measuring different
thicknesses or;
• A measurement displays no value.
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

19
Charging the Battery
1. Connect the R7920 via the included cable to a USB port on a PC or
into a wall outlet using a USB Power Adapter (not included) to charge
the Li-ion battery.
2. Charge the meter until the battery indicator appears full.
3. Remove the charging cable.
Applications
• Monitoring and verifying pipes and pressure vessels
• Industrial manufacturing
Accessories and Replacement Parts
• R7920-PROBE Replacement Probe
• R7950 Ultrasonic Couplant Gel
• R7950/12 Ultrasonic Couplant Gel, Pack of 12
• R7950/5L Ultrasonic Couplant Gel, 5L
• R9060 5-Step Calibration Block
• R8888 Deluxe Hard Carrying Case
Don't see your part listed here? For a complete list of all accessories and
replacement parts visit your product page on www.REEDInstruments.com.
Product Care
To keep your instrument in good working order we recommend the following:
• Store your product in a clean, dry place.
• Charge the battery as needed.
• If your instrument isn't being used for a period of one month or longer
please remove the battery.
• Clean your product and accessories with biodegradable cleaner. Do not
spray the cleaner directly on the instrument. Use on external parts only.
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com

20
Appendix A
Material Sound Velocities Table
Note: The sound velocities listed below are for reference only.
Material Description
in/µs m/s
User dene 1 0.233 5920
User dene 2 0.233 5920
User dene 3 0.233 5920
Aluminum 0.250 6340-6400
Steel, common 0.233 5920
Steel, stainless 0.226 5740
Brass 0.173 4399
Cooper 0.186 4720
Iron 0.233 5930
Cast Iron 0.173-0.229 4400-5820
Lead 0.094 2400
Nylon 0.105 2680
Silver 0.142 3607
Gold 0.128 3251
Zinc 0.164 4170
Titanium 0.236 5990
Tin 0.117 2960
Acrylic resin 0.109 2760
Epoxy resin 0.100 2540
Ice 0.157 3988
Nickel 0.222 5639
continued...
REED Instruments
1-877-849-2127 | [email protected] | www.reedinstruments.com