Reed Instruments R6200 User manual

WBGT
Heat Stress
Meter
Instruction
Manual
R6200
1.888.610.7664[email protected] REED-Direct.com

2
Table of Contents
Introduction ................................................................................................ 3
Product Quality........................................................................................... 3
Safety ......................................................................................................... 3
Features...................................................................................................... 4
Specications..........................................................................................4-5
Included...................................................................................................... 5
Instrument Description............................................................................... 6
Display Description .................................................................................... 6
Operating Instructions...........................................................................6-12
Power ON/OFF...................................................................................... 6
MAX/MIN/AVG....................................................................................... 7
Indoor/Outdoor Temperature Mode Selection ...................................... 7
Switching the Temperature Unit of Measure ......................................... 7
Switching the Pressure Unit of Measure ............................................... 7
Temperature Display Modes.................................................................. 7
Data Hold............................................................................................... 8
Auto-Power Off ..................................................................................... 8
Backlight Function................................................................................. 8
Internal Memory..................................................................................... 8
Memory Recall....................................................................................... 9
Clear Stored Readings .......................................................................... 9
WBGT Audible Alarm Threshold Setting ............................................... 9
Turn Alarm Function ON/OFF.............................................................. 10
Global Temperature/Ambient Temperature/Humidity
Offset Function...............................................................................10-11
Globe Temperature Offset .............................................................. 10
Ambient Temperature Offset .......................................................... 11
Humidity Offset............................................................................... 11
continued...
1.888.610.7664[email protected] REED-Direct.com

3
Pressure Offset Function..................................................................... 11
Error Codes ......................................................................................... 11
Battery Replacement................................................................................ 12
Applications.............................................................................................. 12
Accessories and Replacement Parts ....................................................... 12
Product Care ............................................................................................ 13
Product Warranty ..................................................................................... 13
Product Disposal and Recycling .............................................................. 14
Product Support....................................................................................... 14
Introduction
Thank you for purchasing your REED R6200 WBGT Heat Stress Meter.
Please read the following instructions carefully before using your instrument.
By following the steps outlined in this manual your meter will provide years
of reliable service.
Product Quality
This product has been manufactured to meet stated product specications.
If a certicate of calibration is required please contact the nearest authorized
REED distributor or authorized Service Center. Please note an additional fee
for this service will apply.
Safety
Never attempt to repair or modify your instrument. Dismantling your product,
other than for the purpose of replacing batteries, may cause damage that
will not be covered under the manufacturer's warranty. Servicing should only
be provided by an authorized service center.
1.888.610.7664[email protected] REED-Direct.com

4
Features
• Measuresambienttemperature,humidity,wetbulbtemperature,black
globe temperature, WBGT (wet bulb global temperature), heat stress
index, dew point and pressure
• HeatStressIndexmeasureshowhotitfeelswhenhumidityiscombined
with temperature, air movement and radiant heat
•
Black Globe Temperature (GT) monitors the effects of direct solar radiation
on an exposed surface
• In/OutfunctiondisplaystheWBGTvaluewithorwithoutdirectsunexposure
• Multi-linebacklitLCDdisplaysimultaneouslydisplays4measurements
• Maximum,Minimum,AverageandDataHoldfunctions
• Internalmemorystoresupto99measurements
• Userselectableunitofmeasure(°For°C)
• UseradjustableWBGTthresholdalarm(audible)
• Tripodmountforlong-termmonitoring
• Lowbatteryindicatorandautoshutoff
Specifications
Temperature
MeasuringRanges: AirTemperature:32to122°F(0to50°C)
 BlackGlobe:32to176°F(0to80°C)
WBGT(Indoor):59to138.2°F(15to59°C)
WBGT(Outdoor):59to132.8°F(15to56°C)Ω
Accuracy: AirTemperature:±1.1°F(±0.6°C)
BlackGlobe:±0.6°C(20~50°C),other±1°C
 WBGT(Indoor):±2.7°F(±1.5°C)
 WBGT(Outdoor):±3.6°F(±2°C)
Resolution: 0.1°F/°C
Humidity
MeasuringRanges: 0to99.9%RH
Accuracy(@25°C): 10to70%RH:±3%
 RestofRange:±5%
Resolution: 0.1%RH
continued...
1.888.610.7664[email protected] REED-Direct.com

5
Barometric Pressure
Measuring Range:
300 to 1100hPa (inHg, mmHg switchable)
Accuracy: ±1.5hPa
Resolution: 1hPa, 0.1inHg, 0.1mmHg
General Specifications
DewPoint/WetBulbCalculation: Yes
Response Time: 1 sec
Display: LCD
Backlight: Yes (non-condensing)
Data Hold: Yes
Min: Yes
Max: Yes
Average: Yes
InternalMemory: Yes,upto99measurements
AutoShut-Off: Yes(after15minutes/off)
User Adjustable
WBGT Alarm: Yes (audible)
Tripod Mountable: Yes
LowBatteryIndicator: Yes
Power Supply: 4 x AAA Batteries, Optional AC Adapter
Product Certications: CE, RoHS
OperatingTemperature: 32to122°F(0to50°C)
OperatingHumidity: <80%(non-condensing)
StorageTemperature: -4to122°F(-20to50°C)
StorageHumidity: <90%(non-condensing)
Dimensions: Instrument: 6.4 x 2.3 x 1.3"
 (162x58x32mm)
Black Brass Ball Diameter: 2.0" (50mm)
Weight: 4.8oz(136g)
Included
• Batteries
1.888.610.7664[email protected] REED-Direct.com

6
Instrument Description
1. Black Globe Sensor
2. Temperature & Humidity
Sensor
3. LCDDisplay
4. Hold Button
5. Mode Button
6. Set Button
7. Power Button
8. Max/MinButton
9. UnitofMeasurementButton
10. Backlight Button
Display Description
1. Alarm Indicator
2. Relative Humidity Indicator
3. Ambient Temperature Indicator
4. HI, DPT, WB, GT, WBGT
Indicator
5. Barometric Pressure Indicator
Operating Instructions
Power ON/OFF
1. Push the PWR button to turn the meter on.
To turn the meter off, press and hold the
PWR button for approximately 3 seconds.
2. Whenthemeterispoweredon,theLCDdisplaystheWBGTmodeand
the previously selected "Indoor or Outdoor" WBGT measurement mode.
3. Shortly after, a beep will sound and the instrument will begin taking
measurements.
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
continued...
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
3
4
5
6
7
8
9
10
1.888.610.7664[email protected] REED-Direct.com

7
MAX/MIN/AVG
1. Press the MAX/MIN button to cycle through
the maximum, minimum and average
measurements of Ambient Temperature,
Global Temperature and Relative Humidity
since the instrument was powered on.
2. To clear the maximum, minimum and average
readings, press and hold the MAX/MIN
buttonuntil"CLr"appearsatthebottomof
theLCD.Theinstrumentwillautomatically
return to normal operation once the readings
have cleared.
Note:WhenthemeterisMAX/MIN/AVGfunction,theHOLD and MODE
buttons are disabled.
Indoor/Outdoor Temperature Mode Selection
When in the WBGT mode, press and hold the UNIT button to toggle
between indoor or outdoor temperature. The instrument automatically
calculates the measurement using the following parameters:
1. Outdoor formula WBGT = 0.7Tw (wet bulb temperature) + 0.2Tg
(globe temperature) + 0.1Td (air temperature).
2. Indoor formula WBGT = 0.7Tw (wet bulb temperature) + 0.3Tg
(globe temperature).
Switching the Temperature Unit of Measure
Press the UNITbuttontoswitchbetween°Cand°F.
Switching the Pressure Unit of Measure
Press the BKLT button to change the pressure measuring unit.
(hpa--> inHg--> mmHg).
Temperature Display Modes
Press the MODE button to toggle through the GT (Globe temperature) -->
WBGT temperature --> HI (Heat index) --> DPT (Dew point) --> WB (Wet
bulb temperature measurements).
continued...
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
1.888.610.7664[email protected] REED-Direct.com

8
Data Hold
Press the HOLDbuttonundernormalmeasurementanda"HLD"icon
appears on the display to indicate that the meter is in Data Hold.
Note: When data hold is active the MAX/MIN and SET buttons are disabled.
Auto-Power Off
To preserve battery life, the meter is programmed to turn off after
15 minutes of inactivity.
1. To turn this function off, press and hold the HOLD Button while powering
on the meter.
2. Release both buttons simultaneously.
3. TheLCDwillmomentarilydisplay"n"whilepoweringonindicating
the auto-power off feature is disabled.
4. If the meter is turned off then back on, the "Auto-Power Off" feature
will be enabled again.
Backlight Function
Press and hold the "BKLT"buttontoturntheLCDBacklightONorOFF.
Internal Memory
TheR6200hastheabilitytorecordupto99
temperature/relativehumiditypointsinternally.
1. Press the SET button to save a reading.
2.
While the reading is being saved, the "REC"
indicator will appear next to the temperature
reading and the record number appears at the
bottomoftheLCDforapproximately
2 seconds.
continued...
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
1.888.610.7664[email protected] REED-Direct.com

9
Memory Recall
1. Press and hold the MODEbuttontorecalltherecordedTemperature/
RH measurement values and sequential number.
2. Press the HOLD button to scroll up the stored readings.
3. To scroll down the stored readings, press the BKLT button.
4. To exit memory recall function, press and hold the MODE button at which
point you will be redirected into the WBGT alarm threshold setting.
5. Press and hold the MODE button again to exit the memory recall
function and resume normal operation.
Clear Stored Readings
When required, you can clear the stored readings by pressing and holding
the SETbutton.TheLCDdisplaywillindicate"---"conrmingthatthe
stored values have been cleared.
WBGT Audible Alarm Threshold Setting
(ThedefaultWBGTtemperaturealarmvalueissetat31°)
1. Press and hold the MODE button for 2 seconds and the meter will
enter memory recall function.
2. Press and hold MODE button again to enter
WBGT alarm function.
3. Press the HOLD button to increase the value.
4. Press the BKLT button to decrease the value.
5. Press the UNIT button to conrm your
selectionandjumptothenextdigit.
6. Repeat steps 3 to 5 for each digit.
7. Once the alarm is selected, press and hold the
MODE button to save the value and resume
normal operation.
continued...
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
1.888.610.7664[email protected] REED-Direct.com

10
Turn Alarm Function ON/OFF
After setting up the threshold, press the PWR button and the alarm
indicator will display on the screen indicating the alarm is activated.
Press the PWR button again to disable alarm function.
Global Temperature/Ambient Temperature/Humidity
Offset Function
It is recommended that this unit be calibrated
once a year to ensure measurements stay within
manufacturer's specications. In the case that a
user would like to perform self-verication with a
trusted calibration source follow the offset
procedures below.
To enter the offset function:
1. Power off the meter.
2. Press and hold the MODE and BKLT
buttons while powering on the meter.
3. ReleasebothbuttonswhentheLCD
indicates all 3 parameters with "0.0" values
as shown.
Note: Hold the MAX/MIN button and press the POWER button to select
therequiredoffsettemperaturein°Cor°F.
Globe Temperature Offset
1. Hold the UNIT button and then press the HOLD button to increase
the value.
2. Hold the UNIT button and then press the BKLT button time to
decrease the value.
3. Press the MODE and POWER buttons to save the value.
4. TheLCDdisplaywillindicate"SAVE"
conrming the selection.
5. Repower the meter to resume normal operation.
continued...
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
1.888.610.7664[email protected] REED-Direct.com

11
Ambient temperature offset
1. Hold the SET button and then press the HOLD button to increase
the value.
2. Hold the SET button and then press the BKLT button to decrease
the value.
3. Press the MODE and POWER buttons to save the value.
4. TheLCDdisplaywillindicate"SAVE"conrmingtheselection.
5. Repower the meter to resume normal operation.
Humidity Offset
1. Hold the MAX/MIN button and then press the HOLD button to
increase the value.
2. Hold the MAX/MIN button and then press the BKLT button to
decrease the value.
3. Press the MODE and POWER buttons to save the value.
4. TheLCDdisplaywillindicate"SAVE"conrmingtheselection.
5. Repower the meter to resume normal operation.
Pressure Offset Function
1. While in normal operation, press and hold the SET button until the
LCD shows "0.0 hpa".
2. To increase the value press the
HOLD button.
3. To decrease the value press the
BKLT button.
4. Press and hold the POWER button
to save the set value.
5. TheLCDdisplaywillindicate"SAVE"conrmingtheselection.
Note: The compensation range is ±3 hpa.
Error Codes
Code Description
Er1: Sensor failed.
Er2: Out of measured range.
WBGT WBGT
WBGT
GT
%
hpa
AVG
MIN
MAX
WBGT
HIDPT
%
hpa
GT
%
%
REC
hpa
3
4
5
continued...
1.888.610.7664[email protected] REED-Direct.com

12
Battery Replacement
When the low battery symbol "bAt" appears on the display, the batteries
need to be replaced.
1. Open the battery cover by sliding the cover off.
2. Replace the 4 x AAA batteries and secure the battery cover.
Note: If the unit will not be used for a long period of time, remove the
batteries to avoid battery leakage and corrosion of the battery contacts.
Applications
• Sports(leisure,organized,andprofessional)
• Monitorseasonalconditionstoensuresafeenvironmentatschool
or daycare
• Ensuringsafeworkenvironments
Accessories and Replacement Parts
• R9933HumidityCalibrationStandard,33%
• R9975HumidityCalibrationStandard,75%
• R9980HumidityCalibrationKitStandard,33%and75%
• R1500 Tripod
• R9450-ADP International AC Adaptor
• CA-05A Soft Carrying Case
Don't see your part listed here? For a complete list of all accessories and
replacement parts visit your product page on www.reedinstruments.com.
1.888.610.7664[email protected] REED-Direct.com

13
Product Care
To keep your instrument in good working order we recommend the following:
• Storeyourproductinaclean,dryplace.
• Changethebatteryasneeded.
• Ifyourinstrumentisn'tbeingusedforaperiodofonemonthorlonger
please remove the battery.
• Cleanyourproductandaccessorieswithbiodegradablecleaner.Donot
spraythecleanerdirectlyontheinstrument.Useonexternalpartsonly.
Product Warranty
REED Instruments guarantees this instrument to be free of defects in
material or workmanship for a period of one (1) year from date of shipment.
During the warranty period, REED Instruments will repair or replace, at no
charge, products or parts of a product that proves to be defective because
of improper material or workmanship, under normal use and maintenance.
REED Instruments total liability is limited to repair or replacement of the
product. REED Instruments shall not be liable for damages to goods,
property, or persons due to improper use or through attempts to utilize the
instrument under conditions which exceed the designed capabilities. In
order to begin the warranty service process, please contact us by phone at
1-877-849-2127orbyemailat[email protected]todiscussthe
claim and determine the appropriate steps to process the warranty.
1.888.610.7664[email protected] REED-Direct.com

14
Product Disposal and Recycling
Please follow local laws and regulations when disposing or recycling your
instrument. Your product contains electronic components and must be
disposed of separately from standard waste products.
Product Support
If you have any questions on your product, please contact your authorized
REED distributor or REED Instruments Customer Service by phone at
1-877-849-2127orbyemailat[email protected].
Please visit www.REEDINSTRUMENTS.com for the most
up-to-date manuals, datasheets, product guides and software.
Product specifications subject to change without notice.
All rights reserved. Any unauthorized copying or reproduction of
this manual is strictly prohibited without prior written permission
from REED Instruments.
1.888.610.7664[email protected] REED-Direct.com

TEST & MEASURE
WITH CONFIDENCE
CHECK OUT OUR LATEST PRODUCTS!
1.888.610.7664[email protected] REED-Direct.com

1.888.610.7664[email protected] REED-Direct.com