REED PPR75 User manual
Plastic Pipe Fitting Reamers Operating Instructions
PPR75, PPR100, PPR125, PPR150, PPR200, PPR300, PPR400
1. Shaft
2. Carbide
3. Cap Screw
4. Set Screw
(not shown)
Body
Rotate Carbide Insert: Carbide insert has four cutting edges. Change cutting
edge by removing the cap screw and rotating the carbide 180° then reinsert cap
screw and tighten. Replace carbide as needed.
¾” - 1” 1-¼” - 4”
Ref. No. Description Item Code Item Code Qty.
1 SHAFT 44525 44524 1
2 CARBIDE INSERT 24523 24524 1
3a 8-32 CAP SCREW — 24525 1
3b 4-40 CAP SCREW 24522 — 1
4 1/4” - 20 SET SCREW 30087 30087 1
Parts List
54521-213
See Also: RP-0113-103
Plastic Pipe Fitting Reamers Operating Instructions
PPR75, PPR100, PPR125, PPR150, PPR200, PPR300, PPR400
1. Shaft
2. Carbide
3. Cap Screw
4. Set Screw
(not shown)
Body
Rotate Carbide Insert: Carbide insert has four cutting edges. Change cutting
edge by removing the cap screw and rotating the carbide 180° then reinsert cap
screw and tighten. Replace carbide as needed.
¾” - 1” 1-¼” - 4”
Ref. No. Description Item Code Item Code Qty.
1 SHAFT 44525 44524 1
2 CARBIDE INSERT 24523 24524 1
3a 8-32 CAP SCREW — 24525 1
3b 4-40 CAP SCREW 24522 — 1
4 1/4” - 20 SET SCREW 30087 30087 1
Parts List
54521-213
See Also: RP-0113-103
ASSEMBLY
1. Insert Shaft into Body.
2.Makesureshaftisallthewaythroughandushwiththe
bottom of the reamer.
3. Using a 1/8” Allyn wrench, tighten set screw.
Note: These reamers can be used with standard drills, cord-
less drills, or impact drills. For most effective use, run the drill
at a low or medium RPM.
WARNING:3”and4”ttingreamerscreatealargereaction
torque that can cause injury to operator, therefore a standard
1/2” right angle drill is recommended. Use caution when using
these tools. For reaming 3” or 4”, a lower RPM is recommend-
edtoreduceheatandpossibledistortionofthetting.
Plastic Pipe Fitting Reamers Operating Instructions
PPR75, PPR100, PPR125, PPR150, PPR200, PPR300, PPR400
INSTRUCTIONS
1.Cutdamagedpipeasclosetottingaspossible.
2.Selectpropersizettingborer,putitindrillchuck,
and tighten. A standard 1/2” right angle drill is
recommended.
3.Insertttingreamer into broken pipe, ensure tool stays
on center to prevent binding. If no chips are being
made, remove tool and check.
4. Ream old pipe until proper depth is attained.
5.Removedrillandcleanoutchipsfromtting.
NOTE: PPR Fitting Reamers are NOT recommended
for use on pressurized systems.
Reed Manufacturing Company
1425 West 8th Street
Erie, PA 16502 USA
Phone: 800-666-3691 or 814-452-3691
Fax: 800-456-1697 or 814-455-1697
www.reedmfgco.com
54521-213
See Also: RP-0113-103
ASSEMBLY
1. Insert Shaft into Body.
2.Makesureshaftisallthewaythroughandushwiththe
bottom of the reamer.
3. Using a 1/8” Allyn wrench, tighten set screw.
Note: These reamers can be used with standard drills, cord-
less drills, or impact drills. For most effective use, run the drill
at a low or medium RPM.
WARNING:3”and4”ttingreamerscreatealargereaction
torque that can cause injury to operator, therefore a standard
1/2” right angle drill is recommended. Use caution when using
these tools. For reaming 3” or 4”, a lower RPM is recommend-
edtoreduceheatandpossibledistortionofthetting.
Plastic Pipe Fitting Reamers Operating Instructions
PPR75, PPR100, PPR125, PPR150, PPR200, PPR300, PPR400
INSTRUCTIONS
1.Cutdamagedpipeasclosetottingaspossible.
2.Selectpropersizettingborer,putitindrillchuck,
and tighten. A standard 1/2” right angle drill is
recommended.
3.Insertttingreamer into broken pipe, ensure tool stays
on center to prevent binding. If no chips are being
made, remove tool and check.
4. Ream old pipe until proper depth is attained.
5.Removedrillandcleanoutchipsfromtting.
NOTE: PPR Fitting Reamers are NOT recommended
for use on pressurized systems.
Reed Manufacturing Company
1425 West 8th Street
Erie, PA 16502 USA
Phone: 800-666-3691 or 814-452-3691
Fax: 800-456-1697 or 814-455-1697
www.reedmfgco.com
54521-213
See Also: RP-0113-103
This manual suits for next models
6
Table of contents
