Rega Brio-R User manual

-
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 1

C NTENTS
I TRODUCTIO , FEATURES A D TECH OLOGY 1-3
I STALLATIO 3
CO ECTIVITY 4-6
LOUDSPEAKER CO ECTIO S 6-7
I USE / I PUT SELECTIO 7
MUTE / REMOTE CO TROL 8
TECH ICAL SPECIFICATIO 9
TROUBLESHOOTI G 10-13
OW ERS LOG 14
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 2

1
INTR DUCTI N, FEATURES AND TECHN L GY
Thank you for purchasing the Brio-
R the latest version of Rega’s best
selling amplifier.
Housed in a brand new case the Brio-
R draws on the pedigree of the
previous three incarnations of this model. The sonic recipe for the Brio
embodies the best in traditional audio circuits with excellent engineering
practice.
A newly designed output amplifier in the Brio-
R was born after extensive
research by our engineers to develop a low source impedance emitter follower
Class A driver stage. This is based around a complementary pair of 150w
Sanken Darlington output transistors. The technical and sonic improvement
gained by the use of low impedance drivers is well known, however it can
feature high standing currents in the driver stage when using standard
transistor configurations. By combining the low impedance driver with the
Sanken Darlington transistors (with their imbedded thermal bias network
running at a lower standing current) this combination forms a complementary
emitter follower emulating Class A conditions with good thermal stability with
lower standing currents in the driver stage.
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 3

2
Other notable improvements include the input switches (relays) and rotary
volume control. The input relays are in the optimum position, being placed
directly between the input sockets and the amplifier input, shortening the signal
path at this critical stage.
Remote control has been added to the Brio-
R for the first time without
compromising the sonic design of the amplifier. This was achieved by keeping
the remote circuit separate to the audio circuit and having its own dedicated
power supply (via a separate winding on the mains transformer). There is no
direct contact between the microcontroller and the signal path, as the
microcontroller controls the relays and volume control motor is using DC
control voltages.
During the Brio-
R design process Rega reviewed the circuit and improved
the low and high current power supplies, coupling and bypass capacitors,
(where film capacitors are used throughout the signal path). The phono stage
has been improved to reflect the current improvements in the Rega Planar
turntables, where the input sensitivity has been increased along with a revision
of the sub 100Hz part of the phono frequency response.
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 4

3
The output amplifier is capable of driving awkward loads as low as 1.7Ω, below
this the amplifier is protected against shorted speakers and reactive loads.
The power supply uses a low noise generously rated toroidal transformer and
10,000µF smoothing capacitors that provide enough current to drive the most
awkward of loads.
We have avoided superfluous gadgets such as tone controls and headphone
sockets as they obstruct the signal path and degrade sound quality. The Rega
Ear (sold seperately) is a dedicated headphone amplifier designed specifically
for this purpose offering far greater performance than an in built socket.
The Brio- R is utilising the highest quality components and all of our
engineers’ experience to achieve the best sonic performance and ensuring it is
the most advanced and feature packed Brio to date.
INSTALLATI N
The Brio-
R will work well on most surfaces, such as a shelf or table,
provided there is sufficient air around the amplifier to prevent overheating. If
using a turntable, magnetic interference can be avoided by positioning the
amplifier as far away from the cartridge as the tonearm lead will allow. ever
stack other hi-fi equipment directly on top of the amplifier. The heat produced
by the Brio-
R is dispersed to the air by the case itself. Ensure that the case
has an unobstructed air passage around it. ever place it directly on fabric or
carpets.
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 5

4
C NNECTIVITY
All the line level inputs and the line level output are made via RCA (Phono)
connectors. The sockets on Rega amplifiers are identified as follows:
Left: Always the upper row and marked in WHITE
Right: Always the lower row and marked in RED
IMP RTANT: ALWAYS TURN FF THE AMPLIFIER WHEN CHANGING
LEADS & SPEAKER CABLES.
Rear Panel Connections
Input 1 – Phono stage for use with a turntable only.
The Phono input can be used with moving magnet (MM) or HIGH OUTPUT moving coil
(MC) cartridges.
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 6

Earthing: For Rega turntables earthing is achieved via the Phono lead ground
therefore a separate earth is not necessary. If your tonearm has a separate earth
lead it will need to be connected to the grounding nut located on the underside of
the amplifier.
5
Tonearm earthing nut
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 7

6
Input 2-5 – Standard “Line level” Line inputs enable the connection of any
additional sources such as CD players DVD, TU ER etc. ote the record output
is disabled when input 5 is selected.
Input 5 – Record input “line level” We advise if a recording device with the
ability to monitor the recording signal is connected to the amplifier, its output
is connected to input 5 to stop possible feedback issues.
Record output For connection to any recordable device (such as a CD
recorder). The output is a ‘record signal’ as selected by the main input selector
1-4. ote the record output is disabled when input 5 is selected. This output is
not affected by the volume control.
Mains Power lead The supplied power lead should be connected to the ‘Power
in’ socket also located on the rear of the unit.
L UDSPEAKER C NNECTI NS
The Brio- R is capable of driving all normal Hi-Fi loudspeakers, Rega
recommends using loudspeakers with a nominal impedance of 8Ω. It is possible
to run speakers as low as 4Ω however such units may cause the case to exceed
40° C above the ambient temperature.
Top row RED and BLACK left speaker
Bottom row RED and BLACK right speaker
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 8

IN USE
Switch the Brio-
R on by pressing the power button located on the left hand
side of the front panel above the Rega Logo. After a few seconds you will hear
a gentle click indicating the switch on relay has been released and the amplifier
is ready for use.
INPUT SELECTI N
To change between inputs simply press the button marked ‘input’ to cycle
through from 1 to 5.(This button can be held down to cycle quickly).
The selected input is highlighted by the corresponding red LED. Input selection
can also be changed via the supplied remote control handset.
7
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 9

8
MUTE
The mute function is available only via the remote control. This function mutes
the power amplifier outputs. When selected a red LED is illuminated on the
front panel, press again to deselect.
REM TE C NTR L
The Brio-
R is supplied with a dedicated remote control handset which
allows you to select inputs 1 through 5, mute the unit and adjust the volume.
(Batteries included 2 x AAA Alkaline).
Brio-R manual:Cur a manual.qxd 08/04/2011 09:25 Page 10