Regency Fireplace Products Onyx Remote Control User manual

REMOTE CONTROL
BUTTONBUTTON FUNCTIONFUNCTION ACTIONACTION
POWER The POWER button will turn the fireplace on, and enter standby mode.
This will turn on/off all the functions at once but will hold the settings in memory.
MY FLAME Press the MY FLAME button followed by ‘+’ and ‘-’ or ‘f’ and ‘g’ , the unit will cycle through 9 flame
settings.
Flames 1-6 are default settings, 7-9 can be saved as custom settings.
MAIN FLAME/
FLAME PALETTE
Press the MAIN FLAME button to enter the main flame effect adjustment screen, press ‘f’ and ‘g’
button to cycle through Red - Ember - Yellow - Green – Cyan - Blue – Purple – White – 8 Colour
Cycling - Off.
Press ‘+’ and ‘-’ button to adjust the brightness from 10 -100%, total six settings including Off.
Press again to enter the FLAME PALETTE adjustment screen. Press ‘f’ and ‘g’ button to cycle
through Red - Ember - Yellow - Green – Cyan - Blue – Purple – White – 8 Colour Cycling - Off.
Press ‘+’ and ‘-’ button to adjust the brightness from 10 -100%, total six settings including Off.
FLAME SPEED Press the button to enter the FLAME SPEED settings.
Press ‘+’ and ‘-’ button to adjust the speed by five settings.
The remote control should be left on
a flat surface in the room where the
appliance is installed and away from
any direct flow of hot air.

BUTTONBUTTON FUNCTIONFUNCTION ACTIONACTION
GLOWING
EMBERS/
GLOWING LOGS/
DOWN LIGHT/
SYNC
Press the button to enter the GLOWING EMBERS settings, press ‘f’ and ‘g’ button to cycle
through Red - Ember - Yellow - Green – Cyan - Blue – Purple – White – 8 Colour Cycling - Off.
Press ‘+’ and ‘-’ button to adjust the brightness from 10-100%, total six settings including Off.
Press again to enter the GLOWING LOGS adjustment screen.
Press ‘f’ and ‘g’ button to cycle through Red - Ember - Yellow - Green – Cyan - Blue – Pink –
White - 12 Colour Cycling - Red/Ember/Yellow - Yellow/Pink/Ember – Cyan/Blue/Pink – Off.
Press ‘+’ and ‘-’ button to adjust the brightness from 10-100%, total six settings including Off.
Press again to enter the DOWN LIGHT adjustment screen.
Press ‘f’ and ‘g’ button to cycle through Red - Ember - Yellow - Green – Cyan - Blue – Purple –
White – 8 Colour Cycling - Off
Press ‘+’ and ‘-’ button to adjust the brightness from 10-100%, total six settings including off.
Press the button the fourth time to enter the SYNC, the colours of flame palette, fuel bed, log
burning and down light could be synced.
Press ‘f’ and ‘g’ button to cycle through Red - Ember - Yellow - Green – Cyan - Blue – Purple –
White – 8 Colour Cycling - Off
Press ‘+’ and ‘-’ button to adjust the brightness from 10-100%, total six settings including off.
MOOD LIGHT
Press the button to enter the MOOD LIGHT settings, and the setting will cycle through Cold
White - White - Warm White - Light Ember - Ember - Yellow - Gold Yellow - Red - Green - Cyan
- Blue - Light Purple - Purple -13 Colour Cycling and Off.
Press ‘+’ and ‘-’ button to adjust the brightness from 10-100%, total six settings including Off.
HEATING Press the HEATING button, and the heater will cycle the heat setting: AUT - LOW - HIGH - OFF.
The AUTO heating will work after the weekly timer has been set in the MyFlame App.
TIMER Press the TIMER button to set the desired time for the fireplace to run.
The Timer can be set 0.5H, 1.0H, and then each hour up to 10.0H.
-Press the ‘f’ and ‘g’ button to choose different settings such as the colour settings of the
corresponding function.
-Press the ‘+’ and ‘-’ button to increase or decrease the settings such as the light setting.
OPERATING THE APPLIANCE - ADVANCED OPERATION
Heater Settings
Flame Speed
Power
Flame Palette
My Flame Settings
Temperature Sensor
Convection
Display
Glowing Embers/ Glowing Logs/
Downlight/Sync Settings Mood Lighting
Strip
Timer Settings
Heating
Battery Power
Actual Room
Temperature
Timer
Temperature
Setting
TURN ON/OFF
Press button to turn on the flame effect.
Press button to turn off all the functions under the manual
heating control mode.
Press button to turn off the flame effect under
AUTO heating mode.