Regency Fireplace Products RENMARK Quick start guide
Owners &
Installation
PLEASE KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE
Manual
October-25-2013
918-670b
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to this manual. For assistance or
additional information consult an authorised installer, service agency or
the distributor.
FOR YOUR SAFETY
Do not store or use petrol or other ammable vapours and liquids in the
vicinity of this or any other appliance.
Installation and service must be performed by an authorised installer,
service agency or the gas supplier.
Model: F180B-1
RENMARK FREESTANDING WOOD FIRE
Regency Renmark Freestanding Wood Fire
2
Thank-you for purchasing a
REGENCY FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free
enjoyment. Should you have any questions about your product that are not covered in this manual,
please contact the REGENCY DEALER in your area.
Keep those REGENCY FIRES burning.
SAFETY NOTE:
about restrictions and installation inspection requirements in your area.
The authority having jurisdiction should be consulted before installation to determine the need to
obtain a permit.
Regency Renmark Freestanding Wood Fire 3
TABLE OF CONTENTS
MAINTENANCE
Maintenance..........................................................................9
Creosote................................................................................9
.........9
Glass Maintenance................................................................9
Door Latch Adjustment ..........................................................9
Wood Storage........................................................................9
PARTS LIST
Stove Assembly...................................................................10
WARRANTY
Warranty .............................................................................. 11
Data Badge............................................................................4
Unit Dimensions ....................................................................5
INSTALLATION
Residential Installation...........................................................6
Safety Guidelines and Warnings ...........................................6
Brick Installation ....................................................................6
Clearance to Combustibles ...................................................7
.....................................................................7
OPERATING INSTRUCTIONS
Operating Instructions ...........................................................8
Air Slide Control.....................................................................8
................................................................................8
Regency Renmark Freestanding Wood Fire
4
SAFETY LABEL
This is a copy of the label that accompanies
have printed a copy of the contents here for
your review.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
correct one.
Regency Renmark Freestanding Wood Fire 5
UNIT DIMENSIONS
Regency Renmark Freestanding Wood Fire
6
INSTALLATION
1) Please read this entire manual before you
to follow instructions may result in property
damage, bodily injury or even death. Be
aware that local Codes and Regulations may
override some items in this manual. Check
with your local inspector.
2) THE APPLIANCE AND FLUE-SYSTEM
SHALL BE INSTALLED IN ACCORDANCE
WITH AS/NZS 2918:2001 AND THE AP-
PROPRIATE REQUIREMENTS OF THE
RELEVANT BUILDING CODE OR CODES.
APPLIANCES INSTALLED IN ACCORD-
ANCE WITH THIS STANDARD SHALL
COMPLY WITH THE REQUIREMENTS OF
AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY.
ANY MODIFICATION OF THE APPLIANCE
THAT HAS NOT BEEN APPROVED IN
WRITING BY THE TESTING AUTHORITY
IS CONSIDERED TO BE IN BREACH OF
THEAPPROVAL GRANTED FOR COMPLI-
ANCE WITH AS/NZS 4013.
CAUTION: MIXING OF APPLIANCE OR
FLUE-SYSTEM COMPONENTS FROM
DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF
COMPONENTS MAY RESULT IN HAZ-
ARDOUS CONDITIONS. WHERE SUCH
ACTION IS CONSIDERED, THE MANU-
FACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
3) Select a position for your Regency Stove.
Consult the minimum clearance chart for
close clearance installation use listed double
wall connector systems.
4) To insure vertical alignment, suspend a plumb
bob from the ceiling over the exact center
ceiling to indicate the center of the chimney.
5) Check that the area above the ceiling is clear
the stove to combustibles to insure that they
are within the prescribed limits.
6) Mark the location of the pedestal base on the
7) Install chimney according to chimney manu-
facturers instructions. The performance of
part by the chimney system. Too short a
glass, backsmoking when door is open, and
RESIDENTIAL
INSTALLATION
SAFETY GUIDELINES
AND WARNINGS
1) Never use petrol, petrol type lantern fuels,
kerosene, charcoal lighter fuel, or similar
heater. Keep all such liquids well away from
the heater while it is in use.
2) Keep the door closed during operation and
maintain all seals in good condition.
3) Do not burn any quantities of paper, garbage,
petrol, naptha or engine oil in your stove.
4) If you have smoke detectors, prevent smoke
5) -
extensive damage to your stove including
warpage and premature steel corrosion.
6) Do not permit creosote or soot build-up
in the chimney system. Check and clean
7) Your Regency stove can be very hot. You
may be seriously burned if you touch the
stove while it is operating, keep children,
clothing and furniture away. Warn children
8) The stove consumes air while operating,
provide adequate ventilation with an air
duct or open a window while the stove is in
use.
9)
serving another appliance.
10) Do not use grates or andirons or other
methods for supporting fuel. Burn directly
on the base or bricks where supplied.
11) Open the draft control fully for 10 to 15
seconds prior to slowly opening the door
12) Do not connect your unit to any air distribu-
tion duct.
13)
-
wood, “mill ends”, etc. is not allowed as this
Evidence of excessive overheating will void
your warranty. As well, a large portion of
sawmill waste is chemically treated timber,
which is illegal to burn in many areas. Salt
14) No combustible material should be closer
7.
15) DO NOT OPERATE WITH BROKEN
GLASS.
even reduced heat output. Too tall a chimney
may prompt excessive draft which can re-
sult in very short burn times and excessive
heat output.
8) -
protector clearances.
9) -
under the installed chimney.
10) In seismically active areas, Regency recom-
by using the bolt down holes inside the
pedestal.
11) Do not connect this unit to a chimney
serving another appliance.
BRICK INSTALLATION
made to extend the life of your stove and to
radiate heat more evenly.
Important: Remove the packing material from
above and below the top bricks. Check to see
have not become misaligned during shipping.
Regency Renmark Freestanding Wood Fire 7
MINIMUM CLEARANCE TO
COMBUSTIBLE MATERIALS
INSTALLATION
A
B
C
D
E
G
H
Floor Protection
the heater as follows;
which has a thermal resistance of 0.8m2k/w for 4mm sheets of cement
The ue pipe shall extend not less than 4.6m above the top of the oor protector.
NOTE: Installation must be carried out by a licensed installer in accordance
with AS/NZS 2918:2001.
Super Single
Hawkwind
Standard
Default Kit
AHD Special
Insulated
IMPORTANT
Flo-Met Super Single ue kit must be installed with a 130o
ostainless shield positioned
20mm behind decromesh directly on top of the appliance.
Hawkwind Standard ue kit requires a 130ox 900mm
-
wind kit the rear wall clearance is 325mm.
AHD Special Insulated ue kit must be installed with a
ceiling ring must be spaced as such to provide an air gap of 20mm
to the ceiling. An additional 130º x900mm stainless shield must be
appliance.
NOTE: A minimum clearance of 125mm (flat wall) or 150mm (corner wall) must be retained for all wall surfaces to allow for fan access and maintenance.
Regency Renmark Freestanding Wood Fire
8
OPERATING INSTRUCTIONS
4) After about 45 minutes, when your wood
has begun to burn strongly, adjust your draft
level.
WARNING: Never build a roaring re in
a cold stove. Always warm your stove
up slowly!
5) Once a bed of coals has been established
the draft control to a low setting to operate
6) -
tion rate at a moderate level and avoid a
you operate the stove at its maximum
setting, and only after the metal has been
warmed.
7)
expected as the high temperature paint
becomes seasoned. Windows and/or doors
should be left open to provide adequate
ventilation while this temporary condition
exists. Burning the stove at a very high
8) Do not place anything on the stove top
during the curing process. This may result
Pull - Open
WARNING: To build a re in ignorance
or to disregard the information con-
tained in this section can cause serious
permanent damage to the unit and void
your warranty!!
AIR SLIDE CONTROL
Both the primary and air wash drafts are control-
led by the control rod located on the right side
your draft - pull open, and to decrease - push
closed. All units have a secondary draft system
that continually allows combustion air to the
OPERATING
INSTRUCTIONS
With your unit now correctly installed and safety
inspected by your local authority, you are now
the operation of your draft control.
CAUTION: THIS APPLIANCE MUST BE
MAINTAINED AND OPERATED AT ALLTIMES
IN ACCORDANCE WITH THESE INSTRUC-
TIONS.
CAUTION: THE USE OF SOME TYPES OF
PRESERVATIVE-TREATED WOODASA FUEL
CAN BE HAZARDOUS.
WARNING: ANY MODIFICATION OF THE AP-
PLIANCE THAT HAS NOT BEEN APPROVED
IN WRITING BY THE TESTING AUTHORITY
IS CONSIDERED AS BREACHING AS/NZS
4013.
WARNING: DO NOT USE FLAMMABLE
LIQUIDS OR AEROSOLS TO START OR
REKINDLE THE FIRE.
WARNING: DO NOT USE FLAMMABLE LIQ-
UIDS OR AEROSOLS IN THE VICINITY OF
THIS APPLIANCE WHEN IT IS OPERATING.
WARNING: DO NOT STORE FUEL WITHIN
HEATER INSTALLATION CLEARANCES.
WARNING: OPEN AIR CONTROL (AND
DAMPER WHEN FITTED) BEFORE OPENING
FIRING DOOR.
For safety reasons and in order to avoid
over ring of your unit do not burn your
re with the door open or ajar.
FIRST FIRE
When your installation is completed and in-
1) Open control fully.
2)
CAUTION: Never leave unit unattended
if door is left open. This procedure is for
re start-up only, as unit may overheat
if door is left open for too long.
3) With the draft still in the fully open position
the door.
Push - Closed
Regency Renmark Freestanding Wood Fire 9
MAINTENANCE
9)
will increase.
10)
drafting problems may occur. Consult an
experienced dealer or mason on methods
of increasing your draft.
11) Some cracking and popping noises may be
experienced during the heating up process.
These noises will be minimal when your unit
reaches temperature.
12) Before opening your door to reload, open
draft fully for approximately 10 to 15 seconds
minimize any smoking.
13) All fuel burning appliances consume oxygen
during operation. It is important that you
supply a source of fresh air to your unit
while burning. A slightly opened window is
be created by your Regency Stove causing
a draft down your chimney. If this occurs,
slightly open a window near your unit.
CAUTION: If the body of your unit, ue bae
or any part of the chimney connector starts
to glow, you are overring. Stop loading fuel
immediately and close the draft control until
the glow has completely subsided.
14) Green or wet wood is not recommended for
your unit. If you must add wet or green fuel,
open the draft control fully until all moisture
Once all moisture has been removed, the
draft control may be adjusted to maintain
15) If you have been burning your stove on a
low draft, use caution when opening the
door. After opening the damper, open the
before fully opening the door.
16) The controls of your unit or the air supply
passages should not be altered to increase
17) If you burn the unit too slowly or at too low
a setting your unit will not be operating as
says that if your glass is clean, then your
Burn the stove hot enough to keep your
glass clean and you won't need to clean
CREOSOTE
When wood is burned slowly, it produces
tar and other organic vapours, which when
combined with moisture, form creosote. The
creosote vapours condense in the relatively
lining. When ignited, this creosote can result
WARNING: Things to remember in case
of a chimney re:
1. Close all draft and damper controls.
2. CALL THE FIRE DEPARTMENT.
Ways to Prevent and Keep Unit
Free of Creosote
1) Burn stove with the draft control wide open
for about 10-15 minutes every morning
during burning season.
2) Burn stove with draft control wide open
for about 10 - 15 minutes every time you
apply fresh wood. This allows the wood to
achieve the charcoal stage faster and burns
up any unburned gas vapours which might
otherwise be deposited within the system.
3) Only burn seasoned wood! Avoid burning
wet or green wood. Seasoned wood has
been dried at least one year.
4)
smouldering one that can deposit creosote
within the system.
WOOD STORAGE
Store wood under cover, such as in a shed, or
covered with a tarp, plastic, tar paper, sheets
of scrap plywood, etc., as uncovered wood can
absorb water from rain or snow, delaying the
seasoning process.
MAINTENANCE
It is very important to carefully maintain your
wood and maintaining a clean stove and chim-
ney system. Have the chimney cleaned before
the burning season and as necessary during
the season, as creosote deposits may build up
rapidly. Moving parts of your stove require no
lubrication.
5) The chimney and chimney connector should
be inspected at least once every two months
during the heating season to determine is a
creosote buildup has occured.
6) Have chimney system and unit cleaned
by competent chimney sweeps twice a
year during the rst year of use and at
least once a year thereafter or when a
signicant layer of creosote has accu-
mulated (3 mm/1/8" or more) it should be
removed to reduce the risk of a chimney
re.
GLASS MAINTENANCE
Your Regency stove is supplied with 5 mm
Neoceram ceramic glass that will withstand
the highest heat that your unit will produce. In
the event that you break your glass by impact,
purchase your replacement from an authorized
Regency dealer only, and follow our step-by-step
instructions for replacement.
Allow the stove to cool down before cleaning
the glass, do not clean the glass when it is hot.
Do not use abrasive cleaners.
Rear View of Door shown
Allen Screw
Latching
Sleeve
Set
Screw
DOOR LATCH
ADJUSTMENT
The door latch may require adjustment as the
door gasket material compresses over time.
be moved closer to the door frame, causing a
tighter seal;
1) Unscrew latching sleeve.
2) Remove allen screw.
3) Spin door handle clockwise to desired depth.
4) Re-install allen screw and latching sleeve.
5) Adjust set screw to proper depth to ensure
that the handle does not rotate 360 degrees.
Regency Renmark Freestanding Wood Fire
10
PARTS LIST
1
10
16
12
3
4
17
6
7
8
5
13
15
11
14
STOVE ASSEMBLY
8010104 Stainless Steel Air Bar
Part # Description
572
210
346
8
570
10
38
A
B
Regency Renmark Freestanding Wood Fire 11
WARRANTY
Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team
carefully inspects each unit thoroughly before it leaves our door. Fireplace Products Australia Pty. Ltd. is pleased to extend this
warranty to the original purchaser of a Regency Product. This warranty is not transferable.
The Warranty:
Covered under the agreement against manufacturer's defects from the date of purchase
purchase.
warranty, valid with a receipt only. Any item shown to be defective will be repaired or replaced at our discretion. No labour coverage is included with these parts.
Conditions:
through an accredited distributor or agent provided that the defective part be returned to the distributor or agent Transportation Prepaid, if requested. In
Regency is not obliged to arrange warranty repairs and travel and/or additional labour charges will apply.
for results or costs of workmanship from unauthorised service persons or dealers.
-
sary information including customer name, purchase date, serial #, type of unit, problem, and part or parts requested, without this information the warranty
will be invalid.
Exclusions:
performed.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorisation from Regency
Installer: Please complete the following information
Dealer Name & Address:______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.:__________________________________________________________
Register your Regency®warranty online
www.regency-re.com.au
Reasons to register your product online today!
• View and modify a list of all your registered products.
• Request automatic email notication of new product updates.
• Stay informed about the current promotions, events, and special
oers on related products.
• Help assure you get the most out of your warranty.
• Eliminate confusion and frustration if warranty** service is required in
the future.
** Proof of purchase required at time of warranty request.
This manual suits for next models
1
Table of contents
Other Regency Fireplace Products Wood Stove manuals
Regency Fireplace Products
Regency Fireplace Products Alterra CS1205 Quick start guide
Regency Fireplace Products
Regency Fireplace Products Cascades F1500 Quick start guide
Regency Fireplace Products
Regency Fireplace Products S2400M Quick start guide
Regency Fireplace Products
Regency Fireplace Products Pro Series Quick start guide
Regency Fireplace Products
Regency Fireplace Products F2404M Quick start guide
Regency Fireplace Products
Regency Fireplace Products CS1200 Alterra Quick start guide
Regency Fireplace Products
Regency Fireplace Products F3500 Quick start guide
Regency Fireplace Products
Regency Fireplace Products Classic F2450M Quick start guide
Regency Fireplace Products
Regency Fireplace Products I1200S Wood Insert Quick start guide
Regency Fireplace Products
Regency Fireplace Products F2450 User manual
Regency Fireplace Products
Regency Fireplace Products Cascades Series Quick start guide
Regency Fireplace Products
Regency Fireplace Products HUME F250B Quick start guide
Regency Fireplace Products
Regency Fireplace Products F1105S Quick start guide
Regency Fireplace Products
Regency Fireplace Products Alterra F175B-1 Quick start guide
Regency Fireplace Products
Regency Fireplace Products Alterra F175B-2 Quick start guide
Regency Fireplace Products
Regency Fireplace Products F2403M Quick start guide
Regency Fireplace Products
Regency Fireplace Products F180B-1 User manual
Regency Fireplace Products
Regency Fireplace Products Albany F200B-1 Quick start guide
Regency Fireplace Products
Regency Fireplace Products Vancouver F2402M Quick start guide
Regency Fireplace Products
Regency Fireplace Products F150B-1 Quick start guide
