Jøtul F 163 User manual
Jøtul F 162 / Jøtul F 163
UK - Installation and Operating Instructions 4
FR - Manuel d’installation et d’utilisation 15
ES - Instrucciones para instalación 26
NL - Installatie- en montagehandleiding 37
PL - Instrukcja montażu i obsługi z danymi technicznymi 49
Jøtul F 162 / F 163
Manual Version P03
Manualene må oppbevares under hele produktets levetid. The manuals which are enclosed with the product must be kept throughout the product’s
entire service life. Les manuels fournis avec le produit doivent être conservés pendant toute la durée de vie du produit. Los manuales suministrados
con este producto deben guardarse durante todo el ciclo de vida del producto. I manuali inclusi con il prodotto vanno conservati per l’intera durata di
vita del prodotto. Das im Lieferumfang des Produkts enthaltene Begleitmaterial ist über die gesamte Nutzungsdauer aufzubewahren. De bij de haard
meegeleverde handleidingen moeten gedurende de volledige gebruiksduur van de haard bewaard blijven.
Jøtul F 162 Jøtul F 163
2
EU no. 215/1186 - 24/04/2015
'DWDVKHHW)LFKH7HFKQLTXH)LFKDWpFQLFD
6FKHGDGDWL'DWDVKHHW'DWHQEODWW'DQHWHFKQLF]QH
5HTXLUHPHQWV([LJHQFHV5HTXLVLWRV5HTXLVLWL
9HUHLVWHQ)RUGHUXQJHQ
6XSSOLHU
)DEULFDQWH
)RUQLWRUH
9HUHLVWHQ
/LHIHUDQW
3URGXFHQW
-¡WXO$6
3URGXFWPRGHOV
3URGXLWVFRQFHUQpV
0RGHORV
0RGHOOL
3URGXFWPRGHOOHQ
9DULDQWHQGHU)HXHUVWHOOH
0RGHOHSURGXNWX
-¡WXO)6HULHV
-¡WXO)
-¡WXO)
-¡WXO)
(QHUJ\HIILFLHQF\FODVV&ODVVHpQHUJpWLTXH&ODVHGH
HILFLHQFLDHQHUJpWLFD&ODVVHHQHUJHWLFD(QHUJLHHIILFLsQF\
NODVVH(QHUJLHHIIL]LHQ].ODVVH.ODVDHIHNW\ZQRĞFL
HQHUJHW\F]QHM
$
'LUHFWKHDWRXWSXW3XLVVDQFHUpHOOHGHVRUWLH3RWHQFLD
FDORULILFDHPLWLGD(PLVVLRQHGLFDORUHGLUHWWD'LUHFWHZDUPWH
DIJLIWH1HQQZlUPHOHLVWXQJ%H]SRĞUHGQLDPRFJU]HZF]D
N:
(QHUJ\HIILFLHQF\LQGH[,QGH[GHUHQGHPHQWpQpUJpWLTXH
ËQGLFHGHHILFLHQFLDHQHUJHWLFD,QGLFHGLHIILFLHQ]DHQHUJHWLFD
(QHUJLHHIILFLsQF\LQGH[(QHUJLHHIIL]LHQ],QGH[,QGHNV
HIHNW\ZQRĞFLHQHUJHW\F]QHM
(IILFLHQF\DWQRPLQDOKHDWRXWSXW5HQGHPHQWjSXLVVDQFH
QRPLQDOH(ILFLHQFLDDOUHQGLPLHQWRQRPLQDO(IILFLHQ]DDOOD
SRWHQ]DQRPLQDOH(IILFLHQF\ELMQRPLQDOHZDUPWHDIJLIWH /
:LUNXQJVJUDGEHL1HQQKHL]OHLVWXQJ6SUDZQRĞüGODPRF\
]QDPLRQRZHM
x $Q\VSHFLILFSUHFDXWLRQVWKDWVKDOOEHWDNHQZKHQWKHORFDO
VSDFHKHDWHULVDVVHPEOHGLQVWDOOHGRUPDLQWDLQHG
x 7RXWHVOHVSUpFDXWLRQVVSpFLILTXHVGRLYHQWrWUHSULVHVORUV
GHO¶DVVHPEODJHO¶LQVWDOODWLRQRXO¶HQWUHWLHQGHO¶DSSDUHLO
x &XDOTXLHUSUHFDXFLyQHVSHFtILFDTXHGHEDWHQHUVHHQ
FXHQWDGXUDQWHHOPRQWDMHLQVWDODFLyQRPDQWHQLPLHQWRGHO
HTXLSRGHFDOHIDFFLyQ
x 3UHFDX]LRQLVSHFLILFKHGDSUHQGHUHTXDQGRLOULVFDOGDWRUH
YLHQHDVVHPEODWRLQVWDOODWRRPDQWHQXWRLQXQRVSD]LR
x (YHQWXHOHVSHFLILHNHYRRU]RUJVPDDWUHJHOHQGLHZRUGHQ
JHQRPHQZDQQHHUGHSODDWVHOLMNHUXLPWHYHUZDUPLQJZRUGW
JHPRQWHHUGJHwQVWDOOHHUGRIRQGHUKRXGHQ
x %HVRQGHUH0DQDKPHQEHL0RQWLHUXQJ,QVWDOODWLRQXQG
:DUWXQJ
x :V]HONLHV]F]HJyOQHĞURGNLRVWURĪQRĞFLNWyUHQDOHĪ\
SRGMąüJG\ORNDOQ\RJU]HZDF]SRPLHV]F]HĔMHVW
]DPRQWRZDQ\OXENRQVHUZRZDQ\
x )LUHVDIHW\SUHFDXWLRQVVXFKDVVDIHW\GLVWDQFHVZKHQ
LQVWDOOLQJQDWLRQDOVWDQGDUGVORFDOFRGHVDQGUHJXODWLRQV
6HHWKH,QVWUXFWLRQVPDQXDO
x /HVSUpFDXWLRQVGLQFHQGLHWHOOHVTXHOHVGLVWDQFHVGH
VpFXULWpORUVGHOLQVWDOODWLRQOHVXLYLGHVQRUPHVOHVFRGHV
ORFDX[HWOHVUqJOHPHQWDWLRQVQDWLRQDOHV9HXLOOH]OLUHOH
PDQXHOG¶LQVWDOODWLRQ
x 3UHFDXFLRQHVIUHQWHDLQFHQGLRVFRPRGLVWDQFLDGHVHJXULGDG
HQ OD LQVWDODFLyQ HVWiQGDUHV QDFLRQDOHV FyGLJRV ORFDOHV \
UHJODPHQWRV/HDHOPDQXDOGHLQVWDODFLyQ
x 3UHFDX]LRQLSHUODVLFXUH]]DDQWLQFHQGLRFRPHOHGLVWDQ]HGL
VLFXUH]]DGXUDQWHOLQVWDOOD]LRQHOHQRUPDWLYHQD]LRQDOLHORFDOL
/HJJHUHLOPDQXDO
x %UDQGYHLOLJKHLGVPDDWUHJHOHQ]RDOVYHLOLJKHLGVDIVWDQGHQELM
LQVWDOODWLHQDWLRQDOHQRUPHQORNDOHFRGHVHQYRRUVFKULIWHQ
/HHVௗGHLQVWDOODWLHKDQGOHLGLQJ
x )UEUHQQWHFKQLVFKH9HUKlOWQLVVHZLH]%
$XIVWHOOEHGLQJXQJHQXQGQDWLRQDOH)RUGHUXQJHQ6LHKHGLH
0RQWDJHXQG%HGLHQXQJVDQOHLWXQJ
x ĝURGNLEH]SLHF]HĔVWZDSU]HFLZSRĪDURZHJRWDNLHMDN
RGOHJáRĞFLRGPDWHULDáyZSDOQ\FKMDNLHQDOHĪ\]DFKRZDü
SRGF]DVLQVWDODFMLQRUP\NUDMRZHORNDOQHSU]HSLV\L
UHJXODFMH3DWU]LQVWUXNFMDREVáXJL
3
EU no. 215/1186 - 24/04/2015
'DWDVKHHW)LFKH7HFKQLTXH)LFKDWpFQLFD
6FKHGDGDWL'DWDVKHHW'DWHQEODWW'DQHWHFKQLF]QH
5HTXLUHPHQWV([LJHQFHV5HTXLVLWRV5HTXLVLWL
9HUHLVWHQ)RUGHUXQJHQ:\PDJDQLD
6XSSOLHU
)DEULFDQWH
)RUQLWRUH
9HUHLVWHQ
/LHIHUDQW
3URGXFHQW
-¡WXO$6
3URGXFWPRGHOV
3URGXLWVFRQFHUQpV
0RGHORV
0RGHOOL
3URGXFWPRGHOOHQ
9DULDQWHQGHU)HXHUVWHOOH
0RGHOHSURGXNWX
-¡WXO)6HULHV
-¡WXO)
-¡WXO)
-¡WXO)
(QHUJ\HIILFLHQF\FODVV&ODVVHpQHUJpWLTXH&ODVHGH
HILFLHQFLDHQHUJpWLFD&ODVVHHQHUJHWLFD(QHUJLHHIILFLsQF\
NODVVH(QHUJLHHIIL]LHQ].ODVVH.ODVDHIHNW\ZQRĞFL
HQHUJHW\F]QHM
$
'LUHFWKHDWRXWSXW3XLVVDQFHUpHOOHGHVRUWLH3RWHQFLD
FDORULILFDHPLWLGD(PLVVLRQHGLFDORUHGLUHWWD'LUHFWHZDUPWH
DIJLIWH1HQQZlUPHOHLVWXQJ%H]SRĞUHGQLDPRFJU]HZF]D
N:
(QHUJ\HIILFLHQF\LQGH[,QGH[GHUHQGHPHQWpQpUJpWLTXH
ËQGLFHGHHILFLHQFLDHQHUJHWLFD,QGLFHGLHIILFLHQ]DHQHUJHWLFD
(QHUJLHHIILFLsQF\LQGH[(QHUJLHHIIL]LHQ],QGH[,QGHNV
HIHNW\ZQRĞFLHQHUJHW\F]QHM
(IILFLHQF\DWQRPLQDOKHDWRXWSXW5HQGHPHQWjSXLVVDQFH
QRPLQDOH(ILFLHQFLDDOUHQGLPLHQWRQRPLQDO(IILFLHQ]DDOOD
SRWHQ]DQRPLQDOH(IILFLHQF\ELMQRPLQDOHZDUPWHDIJLIWH /
:LUNXQJVJUDGEHL1HQQKHL]OHLVWXQJ6SUDZQRĞüGODPRF\
]QDPLRQRZHM
x $Q\VSHFLILFSUHFDXWLRQVWKDWVKDOOEHWDNHQZKHQWKHORFDO
VSDFHKHDWHULVDVVHPEOHGLQVWDOOHGRUPDLQWDLQHG
x 7RXWHVOHVSUpFDXWLRQVVSpFLILTXHVGRLYHQWrWUHSULVHVORUV
GHO¶DVVHPEODJHO¶LQVWDOODWLRQRXO¶HQWUHWLHQGHO¶DSSDUHLO
x &XDOTXLHUSUHFDXFLyQHVSHFtILFDTXHGHEDWHQHUVHHQ
FXHQWDGXUDQWHHOPRQWDMHLQVWDODFLyQRPDQWHQLPLHQWRGHO
HTXLSRGHFDOHIDFFLyQ
x 3UHFDX]LRQLVSHFLILFKHGDSUHQGHUHTXDQGRLOULVFDOGDWRUH
YLHQHDVVHPEODWRLQVWDOODWRRPDQWHQXWRLQXQRVSD]LR
x (YHQWXHOHVSHFLILHNHYRRU]RUJVPDDWUHJHOHQGLHZRUGHQ
JHQRPHQZDQQHHUGHSODDWVHOLMNHUXLPWHYHUZDUPLQJZRUGW
JHPRQWHHUGJHwQVWDOOHHUGRIRQGHUKRXGHQ
x %HVRQGHUH0DQDKPHQEHL0RQWLHUXQJ,QVWDOODWLRQXQG
:DUWXQJ
x :V]HONLHV]F]HJyOQHĞURGNLRVWURĪQRĞFLNWyUHQDOHĪ\
SRGMąüJG\ORNDOQ\RJU]HZDF]SRPLHV]F]HĔMHVW
]DPRQWRZDQ\OXENRQVHUZRZDQ\
x )LUHVDIHW\SUHFDXWLRQVVXFKDVVDIHW\GLVWDQFHVZKHQ
LQVWDOOLQJQDWLRQDOVWDQGDUGVORFDOFRGHVDQGUHJXODWLRQV
6HHWKH,QVWUXFWLRQVPDQXDO
x /HVSUpFDXWLRQVGLQFHQGLHWHOOHVTXHOHVGLVWDQFHVGH
VpFXULWpORUVGHOLQVWDOODWLRQOHVXLYLGHVQRUPHVOHVFRGHV
ORFDX[HWOHVUqJOHPHQWDWLRQVQDWLRQDOHV9HXLOOH]OLUHOH
PDQXHOG¶LQVWDOODWLRQ
x 3UHFDXFLRQHVIUHQWHDLQFHQGLRVFRPRGLVWDQFLDGHVHJXULGDG
HQ OD LQVWDODFLyQ HVWiQGDUHV QDFLRQDOHV FyGLJRV ORFDOHV \
UHJODPHQWRV/HDHOPDQXDOGHLQVWDODFLyQ
x 3UHFDX]LRQLSHUODVLFXUH]]DDQWLQFHQGLRFRPHOHGLVWDQ]HGL
VLFXUH]]DGXUDQWHOLQVWDOOD]LRQHOHQRUPDWLYHQD]LRQDOLHORFDOL
/HJJHUHLOPDQXDO
x %UDQGYHLOLJKHLGVPDDWUHJHOHQ]RDOVYHLOLJKHLGVDIVWDQGHQELM
LQVWDOODWLHQDWLRQDOHQRUPHQORNDOHFRGHVHQYRRUVFKULIWHQ
/HHVௗGHLQVWDOODWLHKDQGOHLGLQJ
x )UEUHQQWHFKQLVFKH9HUKlOWQLVVHZLH]%
$XIVWHOOEHGLQJXQJHQXQGQDWLRQDOH)RUGHUXQJHQ6LHKHGLH
0RQWDJHXQG%HGLHQXQJVDQOHLWXQJ
x ĝURGNLEH]SLHF]HĔVWZDSU]HFLZSRĪDURZHJRWDNLHMDN
RGOHJáRĞFLRGPDWHULDáyZSDOQ\FKMDNLHQDOHĪ\]DFKRZDü
SRGF]DVLQVWDODFMLQRUP\NUDMRZHORNDOQHSU]HSLV\L
UHJXODFMH3DWU]LQVWUXNFMDREVáXJL
4
Table of contents
Installation manual with technical data
1.0 Relationship to the authorities ..............................4
2.0 Technical data .........................................................4
3.0 Safety .......................................................................7
4.0 Installation ..............................................................8
5.0 Daily use ................................................................11
6.0 Service ...................................................................12
7.0 Maintenance ..........................................................13
8.0 Operational problems - troubleshooting.............13
9.0 Optional Equipment .............................................14
10.0 Recycling...............................................................14
11.0 Guarantee terms....................................................14
On all our products there is a label
indicatingtheserialnumberandyear.Write
this number in the place indicated in the
installation instructions.
Always quote this serial number when
contacting your retailer or Jøtul.
les combustibles recommandés.
Respectez les consignes d'utilisation. Utilisez uniquement
Verwenden Sie nur empfohlenen Brennstoffen.
Montage- und Bedienungsanleitung beachten.
Follow user`s instructions. Use only recommended fuels.
standard
Certificate/
The appliance can be used in a shared flue.
Minimum distance to adjacent combustible materials:
Emission of CO in combustion products
Serial no: Y-xxxx, Year: 200x
Manufacturer:
N-1602 Fredrikstad
Norway
Jøtul AS
POB 1441
Sweden
EUR Intermittent
Nominal heat output
Norway
Country
Operational type
Fuel type
Operation range
Efficiency
Klasse II
Classification
Standard
Flue gas temperature
Room heater fired by solid fuel
Product:
Jøtul
SP Sveriges Provnings- och
221546
Forskningsinstitut AB
SP Swedish National
Testing and Research
Institute
:
Approved by
:
:
:
:
:
:
:
Minimum distance to adjacent combustible materials:
OGC SP
EN
Serial no.
1.0 Relationship to the
authorities
Installation of a fireplace must be according to local codes and
regulations in each country.
Alllocalregulations,includingthosethatrefertonationalandEuropean
standards, shall be complied with when installing the product.
Before use read the Installation and Operating Instructions
carefully. Prior to using the product the installation must be
inspected by a qualifi ed person.
A name plate of heat-resistant material is affi xed to the product
on the underside of the burnchamber (Fig. 3 B). This contains
information about identifi cation and documentation for the
product.
2.0 Technical data
Jøtul F 162 Jøtul F 163
Material: Cast iron Cast iron
Finish: Paint Paint/enamel
Fuel: Wood Wood
Log length, max: 33 cm 33 cm
Flue outlet: Top/rear Top/rear
Flue pipe dimension: Ø150 mm Ø150 mm
Weight: 115 kg 115 kg
Optional equipment: Cover for rear leg, Cover for rear leg,
soapstone top soapstone top
Dimensions, distances: See fig. 1 See fig. 1
Technical data according to EN 13240
Jøtul F 162 Jøtul F 163
Nominal heat output: 5 kW 5 kW
Flue gas mass fl ow: 5,0 g/s 5,0 g/s
Recommended
chimney draught: 12 Pa 12 Pa
Effi ciency: 83%@5,9 kW 82%@5,9 kW
CO emission (13% O2): 0,06% 0,10%
CO emission (13% O2): 792 mg/Nm3 1242 mg/Nm3
Flue gas temperature: 260o C 260o C
Operational type: Intermittent Intermittent
Intermittentcombustionisheretakentomeannormaluseofafireplace.
I.e. that a new flame chamber is lit as soon as the fuel has burnt down
to the appropriate quantity of embers.
ENGLISH
Register your fi replace at jotul.com for a
25-year warranty.
5
ENGLISH
300
903
Fig. 1a
Combustible wall
900061-P09
Min. distance to combustible wall
Jøtul F 162 / Jøtul F 163
925
700
1000
200
*150412
*362 647
*592
972
*831
1207
*1066
687
*587
500
*400
Y
X
235
93
450
447
119
100
789
603
Hole in wall for external air
Ø 100 mm
Hole in floor for external air
Ø 100 mm
Min. measurements floor plate X,Y =
According to national standards
and regulations. See chapter 4.1 * With semi-insulated chimney / covered flue pipe down
towards the product.
6
ENGLISH
External
Integrated
Min. distance to combustible wall protected by approved firewall
Jøtul F 162 / Jøtul F 163
Combustible wall
Firewall
1000
1000
525
300
312
100
547
1050
1100
100
312
547
300
525
900
100
312
1000
1050
312
100
1000
800
800
712
477
150
337
900
900
900061-P09
712
477
150
337
Fig. 1b
7
Air supply
The outside air connection may be fi tted directly to the product
through:
• Through a fl exible supply hose from the outside or chimney
(only if the chimney has its own duct for external air) and to
the product’s outside air connector.
Fig. 2a, through an outside wall
Important!Theknockoutfortheoutsideairconnectionmustberemoved
from the inside. Use safety goggles.
Tip: It is a great advantage if the rear leg is dismounted before
removing the knockout.
1. Lay the product carefully down on its side. You can put
the cardboard packaging on the fl oor to protect it from
scratches, etc.
2. Remove the rear leg.
3. Use a heavy mallet and strike hard in the middle of the
knockout.
Fig. 2b, through the fl oor and ground plate
Fig. 2c, through the fl oor and basement
Fig. 2d, indirectly through an outside wall
3.0 Safety
NB! To guarantee optimal performance and safety, Jøtul stoves must
be fitted by a qualified installer.
Any modifi cations to the product by the distributor, installer or
consumer may result in the product and safety features not
functioning as intended. The same applies to the installation of
accessories or optional extras not supplied by Jøtul. This may
also be the case if parts that are essential to the functioning and
safety of the fi replace have been disassembled or removed.
In all these cases, the manufacturer is not responsible or liable
for the product and the right to make a complaint becomes null
and void.
3.1 Fire Prevention Measures
There is a certain element of danger every time you use your
fi replace. The following instructions must therefore be followed:
• The minimum safety distances when installing and using
the fi replace are given in fig. 1.
• Ensure that furniture and other fl ammable materials are not
too close to the fi replace. Flammable materials should not
be placed within 1 metre of the fi replace.
• Allow the fi re to burn out. Never extinguish the fl ames with
water.
• The fi replace becomes hot when lit and may cause burns
if touched.
• Only remove ash when the fireplace is cold. Ash can
contain hot embers and should therefore be placed in a
non-fl ammable container.
• Ash should be placed outdoors or be emptied in a place
where it will not present a potential fi re hazard.
ENGLISH
8
In case of chimney fi re:
• Close all hatches and vents.
• Keep the fi rebox door closed.
• Check the loft and cellar for smoke.
• Call the fi re service.
• Before use after a fi re an expert must check the fi replace
and the chimney in order to ensure that it is fully functional.
4.0 Installation
N.B. Check that the fi replace is free of any damage prior to
commencing installation.
The product is heavy! Make sure you have assistance when
erecting and installing the fi replace.
4.1 Floor
Foundations
Ensure that the fl oor is strong enough for the fi replace. See
«2.0 Technical data» for weights. It is recommended that fl ooring
which is not fastened to the foundations – so-called fl oating
fl ooring – is removed during installation.
Combustible fl oor protection
If the fi replace is to be mounted on a combustible fl oor, cover
the fl oor under and in front of the fi replace with a plate of metal
or other non- combustible material. The recommended minimum
thickness is 0,9 mm.
Jøtul recommends that any fl ooring made of combustible
material, such as linoleum, carpets, etc. should be removed
from under the fl oor plate.
The plate must be in accordance with national laws and
regulations.
Contact your local building authority regarding restrictions and
installation requirements.
4.2 Walls (fi g. 1a)
Distance to wall made of combustible
material
You may use the fi replace with an uninsulated fl ue pipe provided
the distances to walls made of combustible materials are as
shown in fig. 1.
Distance to wall with insulated fl ue pipe: Se fig. 1.
Distance to walls covered by a fi rewall
(fi g. 1b and fi g. 1c)
Contact your local building authority regarding restrictions and
installation requirements.
Firewall requirement
The fi rewall must be at least 100 mm thick and be made of
brick, concrete-stone or light concrete. Other materials and
constructions with satisfactory documentation may also be used.
Distance to non combustible walls
By non combustible one means a non load-bearing wall of solid
brickwork/concrete.
Contact your local building authority regarding restrictions and
installation requirements.
4.3 Chimneys and fl ue pipes
• The fi replace can be connected to a chimney and fl ue
pipe approved for solid fuel fi red appliances with fl ue gas
temperatures specifi ed in «2.0 Technical data».
• The chimney’s cross-section must be at least as big as
the fl ue pipe’s cross-section. See «2.0 Technical data» when
calculating the correct chimney cross-section.
• Several solid fuel fi red appliances can be connected to the
same chimney if the chimney’s cross-section is suffi cient.
• Connection to the chimney must be carried out in accordance
with the installation instructions from the supplier of the
chimney.
• Before making a hole in the chimney the fi replace should be
test-mounted in order to correctly mark the position of the
fi replace and the hole in the chimney. See fig.1 for minimum
dimensions.
• Ensure that the fl ue pipe is inclined all the way up to the
chimney.
• Use a fl ue pipe bend with a sweeping hatch that allows it to
be swept.
Be aware of the fact that it is particularly important that
connections have a certain flexibility in order to prevent
movement in the installation leading to cracks.
N.B. A correct and sealed connection is very important for
the proper functioning of the product.
Chimney draught; See «2.0 Technical data». If the draught
is too strong you can install and operate a fl ue damper to
control the draught.
4.4 Assembly prior to installation
The product is delivered in a single packing case.
After unpacking the stove check that the stove is free of any
damage and that the regulating handles works.
ENGLISH
9
ENGLISH
4.5 Selfclosing doormechanism
The product is delivered with a selfclosing doormechanism. If
wanted this can be removed.
Fig. 3
g
g
A
B
1. Unscrew the screw and nut (fig. 3A).
2. Unhook and remove the spring.
4.6 Fitting the fl ue pipe with the rear
outlet
The product is supplied from the factory with the smoke outlet
fi tted for the top outlet.
NB! Proceed as follows for installation with a rear outlet:
Fig. 4
1. Lift the baffl e (Fig. 4 A) up carefully.
2. Remove one of the side burn plates by lifting them up a
little and then out. (Be aware if using tools, that vermiculite
plates may be damaged by rough handling).
3. Remove the baffl e.
4. Remove the other side burn plate.
5. Remove the exhaust defl ectors (Fig. 4 B).
Fig. 5
6. Unscrew the screws (fig. 5A) and remove the smoke outlet
(fig. 5 B) from the top outlet from the inside of the burn
chamber.
Fig. 6a
7. Unscrew the screws (fig. 6a C) and remove the cover (fig. 6a
B) from the rear outlet from the inside of the burn chamber.
10
Fig. 6b
8. Knock out the removable cover plates (fig. 6b A).
9. Attach the smoke outlet (fig. 6a A) on the inside of the burn
chamber where the cover was.
10. Install the cover (fig. 6a B) where the smoke outlet was.
11. Refi t the exhaust defl ectors (fig. 4 B) and the baffl e plate
(fig. 4A).
4.7 Control of functions
When the product is set up, always check the control functions.
These shall move easily and function satisfactorily.
Jøtul F 162 and F 163 are equipped with the following control:
Ignition vent/air vent
Ignition
Fig. 7a
• Open the ignition vent and air vent by pulling the handle all
the way out. (Use a glove or something similar to protect
your hand in case the handles are hot.)
• Place two logs at the bottom of the burn chamber and pile
the kindling in layers.
• Finally, place a medium-sized log on the top of the pile.
• Place 2 or 3 briquettes or kindling sticks under the top layer
of kindling and light the fi re.
Heating
Fig. 7b
• Leave the ignition-/air vent 24 mm (fig. 7 B) open when the
wood has caught fi re properly and is burning well.
• Close the door.
• You can then regulate the rate of combustion to give the
heat you want by adjusting the air vent.
• Check that the afterburning (secondary combustion) starts.
This is best indicated by yellow, fl ickering fl ames in front of
the holes under the baffl e.
Adding fi rewood
Stoke the stove frequently but only add small amounts of fuel at
a time. If the stove is fi lled too full, the heat created may cause
extreme stress in the chimney. Add fuel to the fi re in moderation.
Avoid smouldering fi res as this produces the most pollution.
The fi re is best when it is burning well and the smoke from the
chimney is almost invisible.
ENGLISH
11
ENGLISH
4.7 Danger of overheating
The fi replace must never be used in a
manner that causes overheating
Overheating occurs when there is too much fuel and/or too much
air so that too much heat develops. A sure sign of overheating
is when parts of the fi replace glow red. If this happens, reduce
the air vent opening immediately.
Seek professional advice if you suspect that the chimney is
not drawing properly (too much/too little draught). For further
information, see «4.0 Installation» (Chimney and fl ue pipe).
5.0 Daily use
Odours when using the fi replace for the
fi rst time
When the fi replace is used for the fi rst time, it may emit an
irritating gas which may smell slightly. This happens because
the paint dries.The gas is not toxic but the room should be
thoroughly ventilated. Let the fi re burn with a high draught until
all traces of the gas have disappeared and no smoke or odours
can be detected.
5.1 Operation
Heating advice
NB: Logs that have been stored outdoors or in a cold room
should be brought indoors 24 hours before use to bring them
up to room temperature.
There are various ways of heating the stove but it is always
important to be careful about what you put in the stove. See
the section on “Wood quality”.
Wood quality
By quality wood we mean most well-known types of wood such as
birch, spruce and pine.
The logs should be dried so that the moisture content is no
more than 20%.
To achieve this, the logs should be cut during the late winter.
They should be split and stacked in a way that ensures good
ventilation. The wood stacks should be covered to protect the
logs from rain. The logs should be brought indoors during early
autumn and stacked/stored for use in the coming winter.
Be especially careful never to use the following materials as fuel in
your fireplace:
• Household rubbish, plastic bags, etc.
• Painted or impregnated timber (which is extremely toxic).
• Laminated wooden planks.
• Driftwood
These may harm the product and are also pollutants.
NB: Never use petrol, paraffin, methylated spirit or similar liquids to
light the fire. You may cause serious injury to yourself and damage to
the product.
Wood consumption
Use of wood, with nominal heat emission: Approx. 1,6 kg/h.
Another important factor for proper fuel consumption is that
the logs are the correct size. The size of the logs should be:
Kindling:
Length: 23-33 cm
Diameter: 2 - 5 cm
Amount per fire: 6 - 8 pieces
Daily use
Firewood (split logs):
Length: 23 - 33 cm
Diameter: Approx. 8 cm
Intervals for adding wood: Approximately every 45 minutes
Size of the fire: 1,2 kg
Amount per load: 2 pieces
Nominal heat output and effi ciency are based on heating with
total 1,15 kg beech (2 logs). The air vent was pulled out 24 mm.
Nominal heat emission is achieved when the air vent is open
approximately 60 %.
Maximum use
Max. load: 2,9 kg/h (max. 3 pieces per load /2,2 kg per load)
12
5.2 Ash removal
Jøtul F 162 / F 163 have an ash pan which makes it easy to
remove the ash.
Fig. 8
1. Scrape the ash through the grate (fig. 8A) in the base plate
and into the ash pan. Use a glove to grab the handle on
the ash pan.
1. Make sure that the ash pan doesn’t fi ll up so high that it
keeps ash from coming through the grate into the pan.
6.0 Service
Warning! Any unauthorised change to the product is not allowed.
Only use original spare parts.
6.1 Changing the burn plates/inner
bottom plate
Fig.9
1. Lift the baffl e (Fig. 9 A) up carefully.
2. Remove one of the side burn plates (Fig. 9 E) by lifting
them up a little and then out. (Be aware if using tools, that
vermiculite plates may be damaged by rough handling).
3. Remove the baffl e.
4. Remove the other side burn plate.
5. Unscrew the M8x25 mm screw on the rear burn plate (Fig.
9 F) and remove the burn plate.
6. Then lift up and remove the inner bottom plate (Fig. 9 C).
Follow the same procedure for installation, but in the opposite
sequence.
ENGLISH
13
ENGLISH
6.2 Changing the baffl e plate
• Follow step 1 -3 under Fig. 9.
• Access is then easy to the smoke defl ectors (Fig.9B) if they
need to be removed. They are situated on 1 knob on the
side and on the air manifold (fig. 9 D).
• Edge them down and remove them through the door.
For re-installation follow the same procedure in the opposite
sequence.
7.0 Maintenance
7.1 Cleaning the glass
The product is equipped with an air wash for the glass. Air is
sucked in through the air vent on the top of the product and
down along the inside of the glass.
However, some soot will always stick to the glass, but the
quantity will depend on the local draught conditions and
adjustment of the air vent. Most of the soot layer will normally
be burned off when the air vent is opened all the way and a fi re
is burning briskly in the fi replace.
Good advice! For normal cleaning, moisten a paper towel
with warm water and add some ash from the burn chamber.
Rub it over the glass and then clean the glass with clean water.
Dry well. If it is necessary to clean the glass more thoroughly
we recommend using a glass cleaner (follow the instructions
on the bottle).
7.2 Cleaning and soot removal
Soot deposits may build up on the internal surfaces of the
fi replace during use. Soot is a good insulator and will therefore
reduce the fi replace’s heat output. If soot deposits accumulate
when using the product, they can easily be removed by using
a soot remover.
In order to prevent a water and tar layer from forming in the
fi replace, you should regularly allow the fi re to burn hot in order
to remove the layer. An annual internal cleaning is necessary to
get the best heating eff ect from your product. It is a good idea
to do this when cleaning the chimney and fl ue pipes.
7.3 Sweeping fl ue pipes to the
chimney
Flue pipes must be swept through the fl ue pipe sweeping hatch
or through the door opening.
One of the baffl es will have to be removed fi rst in order to do this.
7.4 Inspection of the fi replace
Jøtul recommends that you carefully inspect your fi replace
yourself after it has been swept/cleaned. Check all visible
surfaces for cracks. Also check that all joints are sealed and
that the gaskets are in the correct position. Any gaskets showing
signs of wear or deformation must be replaced.
Thoroughly clean the gasket grooves, apply ceramic glue
(available from your local Jøtul dealer) and press the gasket
well into place. The joint will dry quickly.
7.4 Exterior maintenance
Painted products may change colour after several years’ usage.
The surface should be cleaned and brushed free of any loose
particles before new paint is applied.
8.0 Operational problems -
troubleshooting
Poor draught
Check the length of the chimney and that it complies with
national laws and regulations. (See also «2.0 Technical
data» and «4.0 Installation» (Chimney and fl ue pipe) in the
installation manual for information.)
Make sure that the minimum cross section on the chimney is
according to «2.0 Technical data» in the installation manual.
Make sure that there is not anything preventing the smoke
gasses from escaping: branches, trees, etc.
Upon suspicion of excessive/poor draught in the chimney,
seek professional help for measurement and adjustment.
The fi re extinguishes after a while
• Make sure that the fi rewood is suffi ciently dry.
• Find out whether there is negative pressure in the house,
close mechanical fans and open a window close to the
fi replace.
• Check that the air vent is open.
• Check that the fl ue outlet is not clogged by soot.
Unusual amount of soot accumulates on
the glass
Some soot will always stick to the glass, but the quantity
depends on:
• Moisture in the fuel.
• The local draught conditions.
• Air vent opening.
Most of the soot will normally burn off when the air vent is
opened all the way and a fi re is burning briskly in the fi replace.
(See «7.1 Cleaning the glass».)
14
9.0 Optional equipment
9.1 Leg cover - outside air connection
Cat. no. 51012329
9.2 Soapstone top - 50 mm, complete
Cat. no. 51012327
10.0 Recycling
10.1 Recycling packaging
Your fi replace is delivered with the following packaging:
• A wooden pallet that can be cut up and burned in the
fi replace.
• Cardboard packaging that should be taken to a local
recycling facility.
• Plastic bags that should be taken to a local recycling facility.
10.2 Recycling the fi replace
The fi replace is made of:
• Metal that should be taken to a local recycling facility.
• Glass that should be disposed of as hazardous waste.
The glass in the fi replace must not be placed in a regular
source segregation container.
• Vermiculite burn plates that can be disposed of in regular
waste containers.
ENGLISH
11.0 Guarantee terms
1. Our guarantee covers:
Jøtul AS guarantees that the external cast-iron parts are
free from defects in materials or manufacturing at the time of
purchase. You may extend the guarantee on the external cast-
iron parts to 25 years from the date of delivery by registering
the product on jotul.com, and print out the extended guarantee
card within three months of purchase. We recommend that
the guarantee card be kept together with the receipt. Jøtul AS
also guarantees that steel plate parts are free from defects in
materials or manufacturing at the time of purchase for a period
of 5 years from the date of delivery.
The guarantee applies on the condition that the stove has been
installed by a qualifi ed installer in accordance with applicable
laws and regulations and Jøtul’s installation and operating
instructions. Repaired products and replacement items are
guaranteed within the original guarantee period.
2. The guarantee does not cover:
2.1. Damage to consumables such as burn plates, fi re grates,
fl ue baffl es, gaskets and similar as these deteriorate over
time due to normal wear and tear.
2.2. Damage caused as a result of improper maintenance,
overheating, use of unsuitable fuel (e.g of unsuitable fuel
are, but not limited to driftwood, impregnated wood, plank
off cuts, chipboard ) or too moist / wet wood.
2.3. Installation of optional extras for the purpose of rectifying
local draught conditions, air supply or other circumstances
beyond Jøtul’s control.
2.4. Cases involving alterations / modifi cations to the fi replace
without Jøtul’s consent or the use of non-original parts.
2.5. Damage caused during storage at a distributor, transport
from a distributor or during installation.
2.6. Products sold by unauthorized sellers in areas where
Jøtul operates a selective distribution system.
2.7. Associated cost (e.g.but not limited to, transport,
manpower, travel) or indirect damages.
Pellets stoves, glass, stone, concrete, enamel and paint
fi nish (e.g. but not limited to chipping, cracking, bubbling or
discolouration and crazing) are applicable to the national
legislation governing the sale of consumer goods. This
guarantee is valid for purchases made within the territory of
the European Economic Area. All guarantee inquiries must
be addressed to your local authorized Jøtul dealer within a
reasonable amount of time, which shall not be later than 14
days from the date on which the fault or defect fi rst became
apparent. See list of importers and dealers on our web site
www.jotul.com.
If Jøtul is unable to meet the obligations outlined in the above
guarantee terms, Jøtul will off er a replacement product with a
similar heating capacity free of charge.
Jøtul reserve the right to decline of any replacement of parts
or service in the event that the guarantee is not registrated
online. This guarantee does not aff ect any rights under
applicable national legislation governing the sale of consumer
goods. The national complaint right applies from the purchase
date and only in exchange for a receipt / serial number.
63
Jøtul pursue a policy of constant product development. Products supplied may therefore diff er in
specifi cation, colour and type of accessories from those illustrated and described in the brochure.
Jøtul vise sans cesse à améliorer ses produits. C’est pourquoi, il se réserve le droit de modifi er les
specifi cations, couleurs et équipements sans avis prélable.
Quality
Our policy gives our customers quality and safety piece of mind as a result of Jøtul’s vast experience
dating back to when the company fi rst started in 1853.
Qualité
Cette politique nous permet d’off rir à nos clients une qualité et une sécurité reposant sur la vaste
expérience accumulée par Jøtul depuis sa création en 1853.
JøtulAS,
P.o. box 1411
N-1602 Fredrikstad,
Norway
www.jotul.com
Art.no. 10050789-P03
Jøtul AS, Oct. 2018
Other manuals for F 163
1
This manual suits for next models
6
Table of contents
Other Jøtul Wood Stove manuals
Jøtul
Jøtul F 263 User manual
Jøtul
Jøtul F 602 V2 User manual
Jøtul
Jøtul F 400 ECO User manual
Jøtul
Jøtul Scan 65-1 User guide
Jøtul
Jøtul F 602 N User manual
Jøtul
Jøtul F 500 User manual
Jøtul
Jøtul F 370 High Top User manual
Jøtul
Jøtul I 520 F User manual
Jøtul
Jøtul F 400 User manual
Jøtul
Jøtul F50 TL Rangeley User manual
Jøtul
Jøtul C 24 User manual
Jøtul
Jøtul F 600 User manual
Jøtul
Jøtul F 602 CB Technical manual
Jøtul
Jøtul FS 45 User manual
Jøtul
Jøtul F 600 User manual
Jøtul
Jøtul Cube 200 GG WS User manual
Jøtul
Jøtul F 262 User manual
Jøtul
Jøtul F 118 CB Instruction manual
Jøtul
Jøtul F 600 User manual
Jøtul
Jøtul F 105 B User manual
Popular Wood Stove manuals by other brands
HWAM
HWAM 3740 user manual
Burley
Burley Fireball Springdale 9103 Installation instructions & user manual
Osburn
Osburn SOHO Installation and operation manual
Bronpi
Bronpi Bristol-C Supplementary instructions
Mendip Stoves
Mendip Stoves Woodland Large SE Operation and installation manual
Osburn
Osburn OB02042 Installation and operation manual
Quadra-Fire
Quadra-Fire Quadra-Fire Installation, operation, & maintenance instruction
ADURO
ADURO 15-3 Mounting instruction
CARBEL
CARBEL I 100 Manual for use and maintenance
SCAN
SCAN 1005-B Assembly and instruction manual
Ashley
Ashley AP5660L Installation and operating manual
Broseley
Broseley eVolution 5 Installation and operation manual
Nibe
Nibe Flakt Contura C600 Lighting instructions
Breckwell
Breckwell Classic Cast SPC4000 owner's manual
Morsø
Morsø S81-91 Instructions for installation and use
Lacunza
Lacunza Vulcano 7T E3 E/E Instruction book
Golden Eagle
Golden Eagle ECONOMY SERIES 5040 Owner’s Instruction and Operation Manual
Blaze King
Blaze King Royal Guardian RGT-3001-AMP Owner's installation and operation manual