Regency Bellerive I200B-1 Quick start guide

Model: I200B-1
Owners &
Installation
PLEASE KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE
Manual
Oct-13-2015
918-696e
WARNING:
Improper installation, adjustment, alteration, service or maintenance can
cause injury or property damage. Refer to this manual. For assistance
or additional information consult an authorised installer, service agency
or the distributor.
BELLERIVE FIREPLACE INSERT
FPI - FIREPLACE PRODUCTS AUSTRALIA PTY LTD.
1 CONQUEST WAY HALLAM VICTORIA 3803

2Regency Bellerive Fireplace Insert
Thank-you for purchasing a
REGENCY FIREPLACE PRODUCT.
The pride of workmanship that goes into each of our products will give you years of trouble-free enjoyment. Should you
have any questions about your product that are not covered in this manual, please contact the REGENCY DEALER
in your area.
Keep those REGENCY FIRES burning.
SAFETY NOTE: If this wood re is not properly installed, a house re may result. For your safety, follow the installa-
tion instructions, contact local building, re ofcials, or authority having jurisdiction about restrictions and installation
inspection requirements in your area.
The authority having jurisdiction should be consulted before installation to determine the need to obtain a permit.
ONLY CLEAN APPLIANCE WITH A DAMP CLOTH
(NEVER WHEN UNIT IS HOT)
DO NOT USE ANY ABRASIVE CLEANERS
DO NOT BURN (WILL VOID WARRANTY):
• Treated wood • Tea Tree • Oil Based woods • Coal • Garbage
• Cardboard • Solvents • Colored Paper • Trash
Save these
Instructions
CAUTION: BURN UNTREATED WOOD ONLY. OTHER MATERIALS SUCH AS WOOD PRESER-
VATIVES, METAL FOILS, COAL, PLASTIC, GARBAGE, SULPHUR OR OIL WILL DAMAGE THE
FIRE AND ATMOSPHERE.
"This wood heater is designed to burn natural wood only. Higher efciencies and lower emissions gener-
ally result when burning air dried seasoned hardwoods, as compared to green or freshly cut hardwoods."

Regency Bellerive Fireplace Insert 3
table of
contents
OPERATING INSTRUCTIONS
Operating Instructions .........................................................11
Air Slide Control...................................................................11
First Fire .............................................................................. 11
MAINTENANCE
Creosote..............................................................................12
- Ways to Prevent & Keep Units Free of Creosote.......12
Maintenance........................................................................12
Glass Maintenance..............................................................12
Door Latch Adjustment ........................................................12
Wood Storage......................................................................12
PARTS LIST
Heater Assembly .................................................................13
WARRANTY
Warranty ..............................................................................18
Data Badge ............................................................................4
Unit Dimensions ....................................................................5
INSTALLATION
Before Installing Your Insert ...................................................6
Residential Installation ...........................................................6
Safety Guidelines and Warnings ...........................................7
Flue Specifications ................................................................7
Wood Insert Specifications ....................................................7
Brick & Cast Installation .........................................................7
Zero Clearance Dimensions..................................................7
Zero Clearance Box Dimensions...........................................7
Fireplace Clearances .............................................................8
Installation into a Masonry Fireplace .....................................9
Installation into a Factory Built Fireplace ...............................9
Faceplate & Fan Installation ................................................10

4Regency Bellerive Fireplace Insert
SAFETY LABEL
data badge
This is a copy of the label that accompanies each
I200B Fireplace Insert. We have printed a copy of
the contents here for your review.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
there is a difference, the label on the unit is the
correct one.

Regency Bellerive Fireplace Insert 5
DIMENSIONS
dimensions

6Regency Bellerive Fireplace Insert
installation
1) Please read this entire manual before you
install and use your new wood re. Failure
to follow instructions may result in property
damage, bodily injury or even death. Be
aware that local Codes and Regulations may
override some items in this manual. Check
with your local inspector.
2) THE APPLIANCE AND FLUE-SYSTEM
SHALL BE INSTALLED IN ACCORD-
ANCE WITH AS/NZS 2918:2001 AND
THE APPROPRIATE REQUIREMENTS
OF THE RELEVANT BUILDING CODE OR
CODES.
APPLIANCES INSTALLED IN ACCORD-
ANCE WITH THIS STANDARD SHALL
COMPLY WITH THE REQUIREMENTS OF
AS/NZS 4013 WHERE REQUIRED BY THE
REGULATORY AUTHORITY.
ANY MODIFICATION OF THE APPLIANCE
THAT HAS NOT BEEN APPROVED IN
WRITING BY THE TESTING AUTHORITY
IS CONSIDERED TO BE IN BREACH OF
THEAPPROVAL GRANTED FOR COMPLI-
ANCE WITH AS/NZS 4013.
RESIDENTIAL
INSTALLATION
Regency Inserts are constructed with the high-
est quality materials and assembled under strict
quality control procedures that insure years of
trouble free and reliable performance.
It is important that you read this manual thor-
oughly and fully understand the safe instal-
lation and operating procedures. The more
you understand the way your Regency Insert
operates, the more enjoyment you will experi-
ence from knowing that your unit is operating
at peak performance.
BEFORE INSTALLING
YOUR INSERT
1) Please read this entire manual before you
install and use your new wood insert. Failure
to follow instructions may result in property
damage, bodily injury or even death. Install
and use only in accordance with manufactur-
er’s installation and operating instructions.
2) Check your local building codes - Building
Inspection Department. You may require
a permit before installing your insert. Be
aware that local codes and regulations may
override some items in the manual.
WARNING: Careless installation is the
major cause of safety hazard. Check all
local building and safety codes before
installation of unit.
3) Notify your home insurance company that
you plan to install a replace insert or hearth
heater.
4) Your replace insert is heavy and requires
two or more people to move it safely. The
insert can be badly damaged by mishan-
dling.
5) If your existing replace damper control
will become inaccessible once you have
installed your Regency Insert, you should
either remove or secure it in the open posi-
tion.
6) Inspect your replace and ue prior to install-
ing your insert to determine that it is free
from cracks, loose mortar or other signs of
damage. If repairs are required, they should
be completed before installing your insert.
Do not remove bricks or mortar from your
masonry replace.
7) Do not connect the insert to a ue system
servicing another appliance or an air
distribution duct.
CAUTION: MIXING OF APPLIANCE OR
FLUE-SYSTEM COMPONENTS FROM
DIFFERENT SOURCES OR MODIFYING
THE DIMENSIONAL SPECIFICATION OF
COMPONENTS MAY RESULT IN HAZ-
ARDOUS CONDITIONS. WHERE SUCH
ACTION IS CONSIDERED, THE MANU-
FACTURER SHOULD BE CONSULTED
IN THE FIRST INSTANCE.
3) Re-conrm the clearance from the insert to
combustibles to insure that they are within
the prescribed limits.
4) Install ue according to ue manufacturers
instructions. The performance of your wood
re is governed to a very large part by the
ue system. Too short a ue can cause
difcult start-up, dirty glass, backsmoking
when door is open, and even reduced heat
output. Too tall a ue may prompt excessive
draft which can result in very short burn times
and excessive heat output.
5) The oor protector must be of non-combus-
tible material.
6) Do not connect this unit to a ue serving
another appliance.

Regency Bellerive Fireplace Insert 7
installation
BRICK & CAST
INSTALLATION
Insert the rear cast plate rst and then the side
plates ensuring the cut out sections lock in rmly.
The bricks can then be placed on the base of the
rebox between the cast side and rear plates.
Firebrick is included to extend the life of your
heater and radiate heat more evenly.
SAFETY GUIDELINES AND
WARNINGS
1) Never use petrol, petrol type lantern fuels,
kerosene, charcoal lighter fuel, or similar
liquids to start or ‘freshen up’ a re in your
heater. Keep all such liquids well away from
the heater while it is in use.
2) Keep the door closed during operation and
maintain all seals in good condition.
3) Do not burn any quantities of paper, garbage,
and never burn ammable uids such as
petrol, naptha or engine oil in your heater.
4) If you have smoke detectors, prevent smoke
spillage as this may set off a false alarm.
5) Do not overre heater. If the ue connector,
ue bafe or the heater top begin to glow,
you are overring. Stop adding fuel and
close the draft control. Overring can cause
extensive damage to your heater including
warpage and premature steel corrosion.
Overring will void your warranty.
6) Do not permit creosote or soot build-up in
the ue system. Check and clean ue at
regular intervals. Failure to do so can result
in a serious ue re.
7) Your Regency heater can be very hot. You
may be seriously burned if you touch the
heater while it is operating, keep children,
clothing and furniture away. Warn children
of the burn hazard. For safety reasons a
guard around the re is recommended.
8) The heater consumes air while operating,
provide adequate ventilation with an air duct
or open a window while the heater is in use.
9) Do not use grates or andirons or other
methods for supporting fuel. Burn directly
on the base or bricks where supplied.
10) Open the draft control fully for 10 to 15
seconds prior to slowly opening the door
when refuelling the re.
11) Do not connect your unit to any air distribu-
tion duct.
12) Your wood re should burn dry, standard
rewood only. The use of cut timber, ply-
wood, “mill ends”, etc. is not allowed as this
fuel can easily overheat your wood re.
Evidence of excessive overheating will void
your warranty. As well, a large portion of
sawmill waste is chemically treated timber,
which is illegal to burn in many areas. Salt
drift wood and chemically treated re logs
also must not be burned in your wood re.
13) DO NOT OPERATE WITH BROKEN
GLASS.
FLUE
SPECIFICATIONS
Before installing, check and clean your ue
system thoroughly. If in doubt about its condition,
seek professional advice. Your Regency Insert is
designed for installation into a masonry replace.
The appliance, when installed, must be electrical-
ly grounded in accordance with local codes.
Height 597mm
Width 699mm
Depth 468mm
WOOD INSERT
SPECIFICATIONS
Your replace opening requires the following
minimum sizes:
GLASS INSTALLATION
Remove the door from the heater and remove
the glass retainer. Position the glass in the door,
make sure that the glass gasketing will properly
seal your unit, and replace the retainer, it should
rest on the gasket not the glass. Tighten securely,
but do not wrench down on the glass as this
may cause the glass to break.

8Regency Bellerive Fireplace Insert
installation
ZERO CLEARANCE
BOX DIMENSIONS
ZERO CLEARANCE
DIMENSIONS
Important: Non-combustible sheeting of a minimum thickness of 12mm must be used on the front face of the enclosure.

Regency Bellerive Fireplace Insert 9
installation
FIREPLACE CLEARANCES

10 Regency Bellerive Fireplace Insert
installation
INSTALLATION INTO A
MASONRY FIREPLACE
The insert must be installed as per the require-
ments of your local inspection authority.
Regency highly recommends the use of a full
liner as the safest installation and provides the
most optimum performance. Your retailer should
be able to help you decide which system would
be the best for your application.
Full Flue Liner
The use of this connection method not only
increases the safety of your insert by directing
the hot gases up the ue, but will also help
increase the unit's efciency and decrease
creosote deposits in the ue.
When a connected ue or liner is in use, the
insert is able to “breathe” better by allowing a
greater draft to be created. The greater draft can
decrease problems such as, difcult start-ups,
smoking out the door, and dirty glass.
INSTALLATION INTO A
FACTORY BUILT
FIREPLACE
1) When installed in a factory built replace, a
full stainless steel rigid is mandatory, for both
safety and performance purposes. When
a ue or liner is in use, the insert is able to
breathe better by allowing a greater draft to
be created. The greater draft can decrease
problems such as, difcult start-ups, smoking
out the door, and dirty glass.
2) In order to position the ue liner, the exist-
ing rain cap must be removed from your
ue system. In most cases the ue damper
should also be removed to allow passage
of the liner.
3) In most cases opening the existing spark
screens fully should give enough room for
the insert installation. If it does not, remove
and store.
4) If the oor of your replace is below the
level of the replace opening, adjust the
insert's levelling bolts to accommodate the
difference. When additional shimming is
required, use non-combustible masonry or
steel shims.
5) Measure approximately the alignment of
the ue liner with the position of the smoke
outlet hole on the insert to check for possible
offset. If an offset is required, use a proper
stainless steel unit available with the ue
liner.
6) Once the above items have been checked,
slide your insert into position after rst po-
sitioning the ue liner and offset if required.
(Re-install raincap at completion of installa-
tion).