Regency CC40LE-NG Quick start guide

Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
City Series®
Zero Clearance Direct Vent Gas Fireplace
Owners &
Installation Manual
STYLE MODEL
Left Corner CC40LE-NG / CC40LE-LP
Right Corner CC40RE-NG / CC40RE-LP
Tested by:
www.regency-re.com
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach you gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
Warning
Fire or explosion Hazard
failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
919-740a FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 04.26.17

2| City Series
This appliance may be installed in an aftermarket, permanently lo-
cated, manufactured home (USA only) or mobile home, where not
prohibited by local codes.
This appliance is only for use with the type of gas indicated on the
rating plate. This appliance is not convertible fore use with other
gases, unless a certified kit is used.
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The City Series are hand crafted appliances and
have been designed to provide you with all the warmth and charm of a wood fireplace at the flick of a switch. The CC40LE
/CC40RE City Series have been approved by Intertek for both safety and efficiency. As it also bears our own mark, it
promises to provide you with economy, comfort and security for many trouble free years to follow. Please take a moment
now to acquaint yourself with these instructions and the many features of your Regency® Fireplace.

City Series | 3
MANUFACTURED MOBILE HOME REQUIREMENTS
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency® product has been tested and listed by Intertek as a Direct Vent Wall Furnace to the following standards: VENTED GAS
DECORATIVE FIREPLACE CAN/CGA-2.17-M91, and ANSI Z21.50-2014 • CSA 2.22-2014. and GAS-FIRED APPLIANCES FOR USE AT
HIGH ALTITUDES CAN/CGA 2.17-M91.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes
follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the
current CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.
This Regency® mobile/manufactured home listed appliance comes factory equipped with four 1/4" diameter holes located near each corner
of the base. Fasten the fireplace in place using screw, inserted through the holes.
This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to local
codes. See the "Wiring Diagram" section.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
This appliance may only be installed in an aftermarket permanently located, manufactured home (U.S.A only) or mobile home, where not
prohibited by local codes.
This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases,
unless a certified kit is used.
Ensure that structural members are not cut or weakened during installation.

4| City Series
table of contents
Dura-Vent Vertical Termination ....................................41
4" x 6-5/8" venting .......................................................41
Vertical Termination 4" x 6-7/8" venting .....................42
Vertical flue extension kit (part #946-756) ...................43
Ceiling Firestop / firestop spacer (part #946-757) .......43
High Elevation ..............................................................44
Gas Line Installation ....................................................44
Pilot Adjustment ...........................................................44
Gas Pipe Pressure Testing ..........................................44
885 S.I.T. Valve Description .........................................44
Wiring Diagrams ..........................................................45
Inner glass panel (firebox glass) Installation / removal 46
Outer safety glass panel (barrier glass) Installation /
removal ........................................................................48
Outer safety glass panel (barrier glass) Installation / re-
moval ...........................................................................49
LP Conversion Instructions ..........................................50
CC40LE/CC40RE Painted panel installation ...............52
Inner Panels - CC40LE/CC40RE.................................52
Outer Panels - CC40LE/CC40RE ................................52
CC40LE/CC40RE glass panel installation ...................53
CC40LE/CC40RE enamel panel installation ...............55
Burner and Firebox media options ..............................57
Optional driftwood Log set Installation .........................58
CC40LE/CC40RE - Removable drywall guides ...........60
Operating instructions..........................................61-63
First Fire ......................................................................61
Normal Operating Sounds of Gas Appliances .............61
Aeration Adjustment ....................................................61
Lighting Procedure ......................................................62
Shutdown Procedure ...................................................62
Copy of the Lighting Plate Instructions ........................63
Maintenance...........................................................60-62
Maintenance Instructions ............................................64
Log Replacement ........................................................64
Glass Gasket ...............................................................64
Glass ...........................................................................64
Glass replacement .......................................................64
Bulb Replacement .......................................................65
Valve Replacement ......................................................66
Parts List................................................................67-70
CC40LE main assembly ..............................................67
CC40RE main assembly .............................................69
Warranty............................................................................72-75
Copy of Safety Decal .....................................................5
Installation................................................................9-60
Important Message ......................................................9
Before You Start .............................................................9
General Safety Information ..........................................10
Installation Checklist ....................................................10
Heatwave Duct System ...............................................10
Locating Your Gas Fireplace ........................................11
Unit Assembly Prior to Installation ...............................11
Clearances CC40LE/CC40RE .....................................13
Clearances CC40LE/CC40RE .....................................14
Clearances CC40LE/CC40RE .....................................15
Mantel Clearances CC40LE/CC40RE .........................16
Framing Dimensions CC40LE (Left Corner) ................17
Framing Dimensions CC40RE (Right corner) .............18
Wall Board/Drywall Installation CC40LE/CC40RE ......19
Framing and Finishing Inset Installations CC40LE/
CC40RE ......................................................................20
Optional Framing Kit Installation CC40LE/CC40RE ....21
Building additional framing off of the framing kit ..........24
Guidelines for installing a TV / artwork |above the unit 2 5
TV recessed into wall ..................................................25
Exterior Vent Termination Locations ............................26
4” x 6-5/8” Rigid Pipe Cross Reference Chart .............27
Wall Mount On / Off Switch and Battery Holder Installa-
tion ...............................................................................29
Required for all installations .......................................29
Vent Restrictor Position ...............................................30
Horizontal Terminations ...............................................31
Flex Vent 4" x 6-7/8" ....................................................31
Venting Introduction .....................................................32
Venting Arrangement for Horizontal Terminations .......32
Horizontal Terminations ...............................................33
Rigid Pipe 4" x 6-5/8" ...................................................33
Horizontal Terminations ...............................................34
Rigid Pipe 4" x 6-5/8" ...................................................34
Horizontal Venting with Two (2) 90o Elbows .................34
Horizontal Venting with Three (3) 90o Elbows ..............34
Vertical terminations
Rigid Pipe 4" x 6-5/8" ...................................................35
Venting Arrangement for Vertical Terminations ............36
Vertical Terminations Rigid Pipe 4" x 6-5/8" ...............37
Unit Installation with Horizontal Termination ...............38
4" x 6-5/8" venting .......................................................38
Unit Installation with Horizontal Termination ...............39
Dura-Vent
Horizontal terminations ................................................40

City Series | 5
safety decal
This is a copy of the label that accompanies Direct Vent Gas
Fireplace. We have printed a copy of the contents here for your
review. The safety label is located on the front inside base of
the unit, visible when the outer front panel is removed.
NOTE: Regency® units are constantly being improved. Check
the label on the unit and if there is a difference, the label on
the unit is the correct one.
Copy of Safety Decal
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible con-
nectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appli-
ances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.

6| City Series
requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a batteryoperated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, butidentifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

City Series | 7
dimensions
25 1
4
"
642mm
33 3
16
"
842mm
37 1
8
"
943mm
42 7
8
"
1089mm
43 5
8
"
1108mm
47 3
8
"
1203mm
24 1
4
"
616mm
23 1
8
"
587mm
11 7
16
"
291mm
7 1
4
"
183mm
48"
1219mm
4"
102mm
63
4
"
171mm
34 3
8
"
873mm
17 5
8
"
448mm
18 11
16
"
475mm
7 7
8
"
200mm
15 1
16
"
382mm
10 1
4
"
261mm
14 3
4
"
375mm
Note: Height Dimension may vary depending on the height of the leveling legs.
CC40LE (Left Corner) dimensions
Dimensions will appear as (inches)" / (metric)mm
throughout this manual. The inches are rounded to the
nearest 1/16" when converted, when greater accuracy
is required, use the metric dimensions.
Note: These units are non-load bearing.
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

8| City Series
dimensions
34 3
8
"
873mm
17 5/8"
[448mm]
18 11
16
"
475mm
7 7
8
"
200mm
10 1
4
"
261mm
15 1
16
"
382mm
14 3
4
"
375mm
42 7
8
"
1089mm
25 1
4
"
642mm
33 3
16
"
842mm
37 1
8
"
943mm
43 5
8
"
1108mm
47 3
8
"
1203mm
7 1
4
"
183mm
11 7
16
"
291mm
24 1
4
"
616mm
6 3
4
"
171mm
4"
102mm
48"
1219mm
23 1
8
"
587mm
CC40RE (Right Corner) dimensions
Note: Height Dimension may vary depending on the height of the leveling legs.
Dimensions will appear as (inches)" / (metric)mm
throughout this manual. The inches are rounded to the
nearest 1/16" when converted, when greater accuracy
is required, use the metric dimensions.
Note: These units are non-load bearing.

City Series | 9
installation
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAYTO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL,ETC.IT IS IMPERATIVETHAT
CONTROLCOMPARTMENTS,BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS,YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IFTHERE ARE AT RISK INDIVIDUAL
INTHE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
Important Message
SAVE THESE INSTRUCTIONS
City Series Direct Vent Fireplaces must be
installed in accordance with these instructions.
Carefully read all the instructions in this manual
first. Consult the "authority having jurisdiction" to
determine the need for a permit prior to starting the
installation. It is the responsibility of the installer to
ensure this fireplace is installed in compliance with
manufacturer's instructions and all applicable codes.
Before You Start
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
THE APPLIANCE,MUST BE REPLACED
PRIORTOOPERATINGTHEAPPLIANCE.
IFTHE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITH THE MANUFACTURER'S
BARRIER FOR THIS APPLIANCE.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER AT-RISK
INDIVIDUALS
WE RECOMMEND REMOVING THE
GLASS WITH THE GLASS VACUUM
HOLDERS SUPPLIED BY THE MANU-
FACTURER. LOWER THE GLASS TO
REST IN A SAFE PLACE. THIS IS TO
PREVENT DAMAGE TO THE GLASS
EDGES.EXTRA CARE MUST BETAKEN
WHEN REMOVING/INSTALLING THE
GLASS. BREAKAGE OR DAMAGE TO
THE EDGE OF THE GLASS WHICH
OCCURS AS A RESULT OF CARELESS
HANDLING WILL NOT BE COVERED
UNDER WARRANTY.

10 | City Series
installation
Installation Checklist
1. Locate appliance. Refer to the following sections:
a) Locating Your Fireplace
b) Clearances
c) Combustible Mantel Clearances
d) Framing & Finishing
e) Venting. See the "Venting Introduction" to
"Venting Arrangements" sections.
2. Assemble Standoffs. Refer to the "Unit Assem-
bly Prior to Installation" section. (NOTE: must
be done before installing unit into fireplace.)
3. Install vent. See the "Horizontal Installations"
to "Installation Procedures" sections.
4. Install 4 AA batteries into receiver battery box.
Connect receiver to wiring marked receiver,
this will enable operation of the appliance
manually when position in "ON" position.
Note: The wire harness (marked receiver) is
located near the gas valve and will need to be
routed to the exterior of the fireplace from either
the left or right hand side of the appliance prior
finishing.
5. Supply 120 volt power to appliance. This
will be required to operate lights and highly
recommended to operate gas valve. AA
Batteries serve as back up only if 120 volt power
is lost.
6. Make gas connections. Test the pilot. Must be as
per diagram. Refer to the "Gas Line Installation"
& "Pilot Adjustment" sections.
7. Install standard and optional features. Refer
to the following sections where applicable:
a. Safety Glass
b. Firebox (inner) glass
c. Log Set
d. Fireglass
e. Ceramic stones or other approved media
f. Painted, enamel or glass panels (panels
required)
g. Optional Framing Kit
h. Heatwave Kit
8. Plug 3 prong plug for the lights into the
receptacle. The 3 prong plug will be located
near the gas valve on the appliance.
9. Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to customer.
General Safety Information
1. The appliance installation must conform with
local codes or, in the absence of local codes,
with the current Canadian or National Gas
Codes, CAN1-B149 or ANSI Z223.1 Installation
Codes.
2. See general construction and assembly
instructions. The appliance and vent should be
enclosed.
3. This appliance must be connected to the
specified vent and termination cap to the outside
of the building envelope. Never vent to another
room or inside a building. Make sure that the
vent is fitted as per Venting instructions.
4. Inspect the venting system annually for blockage
and any signs of deterioration.
5. Venting terminals shall not be recessed into a
wall or siding.
6. Any safety glass removed for servicing must
be replaced prior to operating the appliance.
7. To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
8. Wear gloves and safety glasses for protection
while doing required maintenance.
9. Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
10. Under no circumstances should this appliance
be modified. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
11. Installation and any repairs to this appliance
should be done by a qualified service person.
A professional service person should be called
to inspect this appliance annually. Make it a
practice to have all of your gas appliances
checked annually.
12. Do not slam shut or strike the glass door.
13. Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be used in
this appliance.
14. The appliance area must be kept clear and
free of combustible materials, (gases and other
flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
Heatwave
Duct System
Optional kit
The HeatWave Air Duct Kit increases the
effectiveness of your fireplace by dispersing warm
air from the fireplace to remote locations in the same
room or other rooms in your home.
Up to two kits may be installed on the fireplace.
Please Note: One adaptor kit #656-995 must be
used with each 946-556.
The HeatWave Duct Kit has different clearance
and framing requirements, check the HeatWave
manual for details.
This includes:
1. Clocking the appliance to ensure the correct
firing rate (rate noted on label 28,500 Btu/h NG/
LP) after burning appliance for 15 minutes.
2. If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
CAUTION:Any alterationtothe product thatcauses
sooting or carboning that results in damage
is not the responsibility of the manufacturer.

City Series | 11
installation
Locating Your
Gas Fireplace
1. When selecting a location for your fireplace,
ensure that the clearances are met.
2. The appliance must be installed on a flat, solid,
continuous surface For example a wood, metal
or concrete floor or in a raised (on the wall) ap-
plication. The appliance must be installed on
a metal or wood panel extending the full width
and depth of the appliance.
3. The CC40LE/CC40RE Direct Vent Gas Fire-
place can be installed in a recessed position
or framed out into the room as in A and B. See
Diagram 1.
AB
Diagram 1
CC40LE/CC40RE
CC40LE/CC40RE
A) Corner Left
B) Corner Right
4. For bedroom installations, check with local
codes before installation. This appliance is
offered with a remote control.
5. The CC40LE/CC40RE Direct Vent Gas Fire-
place is approved for alcove installations, see
"Clearances" section for details.
6. We recommend that you plan your installa-
tion on paper using exact measurements for
clearances and floor protection before actually
installing this appliance. Have an authorized
inspector, dealer, or installer review your plans
before installation.
Note: For vent terminations refer to "Exterior
Vent Termination Locations" section.
Unit Assembly Prior to Installation
Before you start
The CC40LE/CC40RE has 4 standoffs, 2 on one side and 2 at the back that need assembly before
installation.
tooltip
Side and back standoff assembly CC40LE/CC40RE
The standoffs are shipped in a flat position and must be folded into shape and attached.
Take each standoff off the unit by removing one screw and bend into the correct shape. Slot the 2 tabs
of the stand off into the slots in the unit and attach the other end with one screw.
Standoff
locations
Back standoff assembly CC40LE/
CC40RE
Take each standoff off the unit by removing one
screw. Bend into the correct shape (see above). Slot
the 2 tabs of the stand off into the slots in the unit
and attach the other end with one screw.

12 | City Series
installation
Nailing strips CC40LE/CC40RE
Nailing strips are shipped folded flat against the unit.
Fold nailing strips out 90º before installing unit.
Secure nailing strips to framing using wood or
metal screws.
Levelling bolts
There are four levelling bolts - two on each side
that can be adjusted if required.
Access panel removal
The front access panel may be removed for ease
of hooking up gas and electrical. Once complete
ensure that the access panel is reinstalled prior to
any finishing.
The CC40LE/CC40RE has 4 screws to remove
access cover. See locations in diagram to the right.
Side nailing strip
CC40LE
tooltip
Side nailing strip
CC40RE
Top Nailing strip CC40LE/CC40RE
Nailing strip is shipped with the appliance and will
need to be attached. Note that the nailing strips are
not required if using the optional chase or extended
framing kit and may be recycled.
1. Secure nailing strip to appliance with 2 screws.
2. Secure nailing strips to framing using wood or
metal screws.
Leveling bolts
Top nailing strip
tooltip
Top nailing strip
Access panel screws

City Series | 13
installation
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this fireplace and vent
system be installed only in accordance with these instructions.
Clearances CC40LE/CC40RE
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
fireplace and vent system be installed only in accordance with these instructions.
Note: CC40LE shown in illustration. Clearances will be the same for the CC40RE.
Clearance: single sided Dimension Measured From:
A: Mantel Height (min.) ** Top of Fireplace Opening
B: Opening Height 15-1/16" (382mm) Bottom/Top of Fireplace Opening
C: From Floor Min. 0" Bottom of Fireplace Opening
D: Sidewall (on one side) Min. 36" (914mm) Side of Fireplace Opening
E: Mantel Depth (Max.) ** Front of Fireplace Opening
F: Alcove Depth Min. 36" (914mm) Front of Fireplace Opening
G: Convection Air Outlet * Top of Enclosure
H: Convection Air Outlet Opening Offset 0-3" (76mm) Max. offset from top of chase enclosure
I: Chase Enclosure (Min.) 63" (1600mm) From Base of Unit
Hearth 0" No hearth required
** See mantel clearances chart in this manual.
Flue Clearances to Combustibles
Horizontal - Top 3"
Horizontal - Side 2"
Horizontal - Bottom 2"
Vertical 2"
Passing through wall/
floor/ceiling - when
firestop is used.
1-1/2"
Top View
Alcove
The HeatWave Duct Kit has differ-
ent clearance and framing require-
ments, check the HeatWave manual
for details.
*A minimum of 120 square
inches of open area, not
lower than 3" from top of
enclosure, required for all
installations
H
I
A
E
B
C
G
D
F
D
F
CC40 UNIT

14 | City Series
installation
Clearances CC40LE/CC40RE
CC40LE shown
CC40LE shown
E
G
G
G
H
B
I
L
o
w fr
a
min
g
wi
t
h v
e
n
ts
E
G
B
H
I
Fl
oo
r
to
ce
ilin
g
wi
t
h
top
op
Floor to ceiling with top opening
Low framing with vents in front/sides or top

City Series | 15
installation
Clearances CC40LE/CC40RE
CC40LE shown
CC40LE shown
Chase enclosed
H
E
B
I
H
G
G
H
E
B
I
H
G
G
Full framing with vents in front or sides
Full framing with low vents in front or sides

16 | City Series
installation
Mantel Clearances CC40LE/CC40RE
Combustible mantel clearances from top of front facing
are shown in the diagram on the right.
Combustible Material
212 6 4810
Standoff
Wood Stud
(On Edge)
0
14
9”
15-1/16”
10
20
26
Top of
Fireplace
Opening
12" (305mm)
Drywall, wood, wood panel, etc.
2”
To
Bottom
of
Fireplace
Lip

City Series | 17
installation
Framing Dimensions CC40LE (Left Corner)
NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.
Note: A combined minimum of
120 square inches of open area
is required for the convection air
outlet to cool the enclosure. En-
sure clearances for Convection Air
Outlets are met.
See clearances CC40LE/CC40RE
(single sided) in this manual as there
are different methods as to how this
can be achieved.
Note: This appliance must be in-
stalled on a level and solid surface
such as a plywood floor which must
be the full width and depth of the
appliance.
Framing
Dimensions Description CC40LE
A Framing Height 37-3/8” (949mm)
B Framing Width 48-1/4" (1226mm)
C Framing Depth 19" (483mm)
D Unit Base to Top Enclosure (Min.) 63"(1600mm)
G Vent Centerline Height 56-1/4" (1429mm)
NOTE: Unit cannot be load-bearing. All finishing materials must be supported by the framing.

18 | City Series
installation
Framing Dimensions CC40RE (Right corner)
NOTE: Framing may be constructed of combustible material (ie. 2 x 4)and does not require steel studs.
Framing
Dimensions Description CC40RE
A Framing Height 37-3/8” (949mm)
B Framing Width 48-1/4" (1226mm)
C Framing Depth 19" (483mm)
D Unit Base to Top Enclosure (Min.) 63"(1600mm)
G Vent Centerline Height 56-1/4" (1429mm)
Note: A combined minimum of
120 square inches of open area
is required for the convection air
outlet to cool the enclosure. En-
sure clearances for Convection Air
Outlets are met.
See clearances CC40RE (in this
manual) as there are different meth-
ods as to how this can be achieved.
Note: This appliance must be in-
stalled on a level and solid surface
such as a plywood floor which must
be the full width and depth of the
appliance.
NOTE: Unit cannot be load-bearing. All finishing materials must be supported by the framing.

City Series | 19
installation
Wall Board/Drywall Installation CC40LE/CC40RE
WARNING! Risk of Fire! Comply with all minimum clearances to combustibles as specified.
Finishing Instructions
It is important to follow the framing and finishing instructions to ensure proper placement of fireplace into the surrounding framing/finishing materials.
Wall board materials 1/2 in. thick are specified in this installation manual to properly align with the optional finishing methods offered with this appliance. The
CC40LE/CC40RE may be finished to the appliance opening with 1/2 inch thick drywall.
• Ensure that the back and side clearances are maintained.
WARNING! Risk of Fire! Maintain specified air space clearances to combustibles. Inadequate air space could cause overheating and fire.
DO NOT use screws more than 3/4 inch in length on the lower access cover panel. Longer screws may penetrate gas line or damage valve or electrical
components.
Note: It is acceptable to use a high temperature silicone sealant to adhere drywall to lower access cover panel.
The appliance is designed to be used with 1/2 in. wall sheathing materials such as drywall, plywood, wood composites, or non-combustible materials.
Thicker materials may be used. Refer to facing and finishing details in this manual.
Facing Material
• Facing and/or finishing materials must never overhang into the glass opening.
• Facing materials may be combustible or non-combustible
WARNING! Risk of Fire! DO NOT apply combustible materials beyond the minimum clearances. Comply with all minimum clearances to combustibles as
specified in this manual. Overlapping materials could ignite and will interfere with proper operation.
PAINTING
If desired finishing includes a painted wall, 100% acrylic latex, oil-based or standard acrylic paints may be used.
Follow paint manufacturer’s instructions for paint and primer application.

20 | City Series
installation
1. Frame in the enclosure for the unit with framing material
Note: When constructing the framed opening ensure there is sufficient
access to install the gas lines,electrical. Also the wiring harness must be
wall mounted using the receptacle provided with the appliance. The wiring
harness will be located on the right hand side of the appliance if facing the
unit from the front. This must be done prior to any finishing.
2. For exterior walls, insulate the enclosure to the same degree as the rest
of the house, apply vapour barrier and drywall, as per local installation
codes. (Do not insulate the fireplace itself.)
WARNING: Failure to insulate and add vapor barriers to the inside of the
exterior wall will result in operational and performance problems including, but
not limited to: excessive condensation on glass doors, poor flame package,
carbon, blue flames etc. These are not product related issues.
3. The unit does not have to be completely enclosed in a chase. You must
maintain clearances from the vent to combustible materials: See "Clear-
ances" section. Combustible materials can be laid against the side and
back standoffs and the stove base.
4. Combustible material (drywall,wood,wood panels, etc.) may be brought
up to this appliance (top,bottom and sides)
5. Ensure that the material being used does not encroach anywhere in the
area of the glass. This would cause dangerous operating conditions.
6. This appliance comes with a 1/2" lip at top, sides and bottom to hide the
ends of the drywall. The 1/2" side and bottom, front and bottom side lips
supplied with the appliance can alternatively be removed and replaced
with J Style Trim or Metal Corner Bead purchased at your local hardware
store to cover cut/exposed edges of the combustible facing material or
any other finishing materials being used. Six (6) screws secure the bot-
tom front lip. Two (2) secure the bottom side lips and 2 secure the side
if deciding to remove these. These will be hidden so the outer panels (if
installed) will need to be removed to access the screws. See outer panel
removal in this manual.
7. This appliance can also be recessed (using combustible materials) with
a hearth in front of the appliance. This can also extend to the top. See
below for details.
8. The wall behind the unit must be closed off.
Framing and Finishing Inset Installations CC40LE/CC40RE
**Combustible material may extend a minimum of 1/2" and to a maximum
of 2-1/2" from the Front top and open side faces of the appliance. If 2-1/2" is
insufficient non combustible material may be used instead of combustible to
extend the finished material further out or alternatively be staggered if using
combustible materials. See mantle clearance chart for details. The base and
closed side have no limit when it comes to how far the combustible material
may extend out from the appliance.
Note: an offset screwdriver is provided with the appliance for ease of removal/
installation.