Regency Energy E33-NG10 Quick start guide

REGENCY FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC, Canada V4G 1H4
919-379a 09.17.15
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Energy™E33 Gas Insert
Owners & Installation Manual
MODELS: E33-NG10 Natural Gas E33-LP10 Propane
- Do not store or use gasoline or other ammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach you gas supplier, call the re department.
- Installation and service must be performed by a qualied installer, service agency or the gas supplier.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.

2| E33-10 FPI Direct Vent Gas Insert
|
2
REGENCY GAS FIREPLACE INSERT
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by Regency.
The E33 Gas Insert has been designed to provide you with all the warmth and charm of a replace, at
the ick of a switch. The E33-NG10 and E33-LP10 have been approved by Warnock Hersey/Intertek
for both safety and efciency. As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself
with these instructions and the many features of your Regency Fireplace.
Energy E33 Video

E33-10 FPI Direct Vent Gas Insert | 3
| 3
dimensions
28
11
16
"
42 7
16
"
26 3
4
"
16 1
4
"
23 3
4
"
11 1
16
22 3
4
"
46 1
2
"
(1181mm)
(1078mm)
(679mm)
(729mm)
(281mm)
(413mm)
(603mm)
(578mm)
"
31
4
"
13
4
(83mm)
(44mm)
32-1/4
819mm
24-1/2
(622mm)
UNIT DIMENSIONS
LOW PROFILE FACEPLATE

4| E33-10 FPI Direct Vent Gas Insert
|
4dimensions
UNIT DIMENSIONS
OPTIONAL VIGNETTE FACEPLATE WITH SPACER
32”
(813mm)
24-1/2”
(622mm)
46-1/2”
(1181mm)
39-5/16”
(999mm)
26-9/16”
(675mm)
28-3/4”
(730mm)
30-3/8”
(772mm)
14-3/4”
(375mm)
2-1/2”
(64mm)
16-7/16”
(418mm)
11-1/16”
(281mm)
22-13/16”
(579mm)
23-3/4”
(603mm)
VIGNETTE STANDARD WITH SPACER
45”
(1143mm)
28”
(711mm)

E33-10 FPI Direct Vent Gas Insert | 5
| 5
dimensions
UNIT DIMENSIONS
OPTIONAL VIGNETTE FACEPLATE WITHOUT SPACER
34-1/16”
(865 mm)
24-1/2”
(622 mm)
46-1/2”
(1181mm)
39-5/16”
(999mm)
28-3/4”
(730mm)
26-9/16”
(675mm)
30-3/8”
(772mm)
14-3/4”
(375mm)
1-5/16”
(33mm)
18-15/16”
(481mm)
13-9/16”
(344mm)
22-13/16”
(579mm)
23 3/4”
(603mm)
25-1/16”
(637mm)
VIGNETTE STANDARD- NO SPACER

6| E33-10 FPI Direct Vent Gas Insert
|
6dimensions
UNIT DIMENSIONS
OVERSIZE BACKINGPLATE WITH SPACER

E33-10 FPI Direct Vent Gas Insert | 7
| 7
dimensions
UNIT DIMENSIONS
OPTIONAL 4 SIDED VIGNETTE FACEPLATE
(813 mm)
”
24-1/2
(622mm)
46-1/2”
”
(1181mm)
39-5/16”
(999mm)
30-7/8”
(784mm)
26-7/16”
(672mm)
2-3/16”
(56mm)
5”
(127mm)
22 13/16”
(579mm)
23 3/4”
(603mm)
4 SIDED VIGNETTE FACEPLATE
2-1/2”
(64mm)
2-3/16
(54mm)

8| E33-10 FPI Direct Vent Gas Insert
|
8table of contents
DIMENSIONS
Unit Dimensions Low Prole Faceplate.........................3
Unit Dimensions Optional Vignette Faceplate
With Spacer...................................................................4
Unit Dimensions Optional Vignette Faceplate Without
Spacer ...........................................................................5
Unit Dimensions Oversize Backingplate With Spacer...6
Unit Dimensions Optional 4 Sided Vignette Faceplate..7
SAFETY LABEL
Copy Of Safety Label ....................................................9
REQUIREMENTS
MA Code - Co Detector ...............................................10
INSTALLATION
Important Message For Your Safety ............................ 11
Before You Start .......................................................... 11
Gas Pressure Testing ..................................................12
Specications ..............................................................12
Installation Into A Solid Fuel Burning Fireplace Or
Factory Built Fireplace.................................................12
Installation Checklist....................................................12
Materials Required ......................................................12
Gas Insert Aeration System.........................................13
Minimum Fireplace Opening........................................13
Combustible Mantel Clearances................................14
Minimum Clearances To Combustibles .......................14
Gas Connection ..........................................................15
Venting.........................................................................15
Flue Liner Installation ..................................................15
Gas Pipe Pressure Testing ..........................................16
SIT 829 Valve Description ...........................................16
DC Spark Igniter Battery Installation ...........................16
Optional Brick Panel....................................................16
Brick Panel Installation ................................................17
Log Set Installation......................................................18
Conversion Kit 342-969 From NG To LP.....................21
For E33-10 Using Sit 829 Nova Gas Valve .................21
Optional Vignette Faceplate Installation......................22
Spacer Installation For 3 Sided Vignette Faceplate ....23
Oversize Backing Plate Installation .............................24
Optional Vignette Inlay Installation ..............................25
Optional Hearth Trim Installation- Vignette Faceplate
With Spacer And Low Prole Faceplate ......................27
Optional Hearth Trim Installation- Vignette Faceplate
Without Spacer ...........................................................28
Optional Hearth Trim Installation-Low Prole .............29
Safety Screen Installation- Low Prole Faceplate.......30
Standard Flush Door ...................................................30
Wiring Diagram............................................................31
Optional Wall Thermostat ............................................31
OPERATING INSTRUCTIONS
First Fire ......................................................................32
Operating Instructions .................................................32
Lighting Procedure ......................................................32
Shutdown Procedure...................................................32
Copy Of Lighting Instruction Plate..............................33
Automatic Convection Fan Operation..........................33
Normal Operating Sounds Of Gas Appliances ............33
MAINTENANCE
Maintenance Instructions.............................................34
General Vent Maintenance ..........................................34
Log Replacement ........................................................34
Glass Gasket...............................................................34
Door Glass ..................................................................35
Fan Maintenance.........................................................35
Valve Assembly Removal And Installation...................36
PARTS LIST
Main Assembly ............................................................37
Burner & Log Assembly ...............................................38
Vignette Faceplate ......................................................39
WARRANTY
Warranty .....................................................................40

E33-10 FPI Direct Vent Gas Insert | 9
| 9
safety decal
This is a copy of the labels that accompany each E33 Gas Insert. We have printed a copy of the contents here for your review. The safety label is located
on a plate inside the base of the unit visible when the bottom louver is opened. Ensure that the safety label is attached to the unit.
NOTE: Regency units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
COPY OF SAFETY LABEL
NATURAL GAS FIREPLACE INSERT: MODEL E33-
NG1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 5“ WC
(1.25 kpa)
Low Setting Man. Pressure 1.1" WC
(0.27 kpa)
Max. Manifold Pressure 3.8" WC
(0.95 kpa)
Orifice Size 31 DMS
D
E
F
H
G
A
B
CI
Part #: 919-378a
Colour: Black on Grey except selected text is in red as per this print.
Size: Print 100%
Material: 2 ml silver matt polyester (DPM SMS)
Jun 3/14: Created draft
May 4/15: Rev. A added safety screen with Vignette
*Printer: Continue number sequence from 918-491 - do not restart at 0
MADE IN CANADA /FABRIQUE AU CANADA
Mantel Clearances
DO NOT REMOVE THIS LABEL /
NE PAS ENLEVER CETTE ETIQUETTE
Serial No. / No de serie
Duplicate Serial number
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the
Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in the United States, or when such a standard is not
applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard
for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details.
WARNING: This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel
Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part
3280, Manufactured Home Construction and Safety Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA
501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
AVERTISSEMENT: Ce foyer a été converti pour utilisation avec un foyer au gaz encastrable et ne peut être utiliser pour brûler du bois ou d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remplacées et que le foyer ait été approuvé de nouveau par l'autorité compétente.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
For use with glass doors certified with the appliance only Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil
VENTED GAS FIREPLACE HEATER - FOYER AU NOT FOR USE WITH SOLID FUELS. /
GAZ À ÉVACUATION - NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.
É ÉQUIP A L'UISINE POUR GAZ PROPANE
É ÉQUIP A L'UISINE POUR GAZ NATURAL
FPI Fireplace Products International Ltd.,
Delta BC, CANADA
Pression d'allimentation minimum
Pression la tubulure d' chappement basse
à é
Pression la tubulure d' chappement lev e
à é é é
Dimensions de l'orifice
D bit Calorifique minimumé
D bit Calorifique maximumé
Pression d'allimentation minimum
Pression la tubulure d' chappement basse
à é
Pression la tubulure d' chappement lev e
à é é é
Dimensions de l'orifice
D bit Calorifique minimumé
D bit Calorifique maximumé
298
298
Model/Modele: E33-NG10
919-378a
Model/Modele: E33-LP10
NATURAL GAS FIREPLACE INSERT: MODEL E33-NG10
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 5“ WC (1.25 kpa)
Low Setting Man. Pressure 1.1" WC (0.27 kpa)
Max. Manifold Pressure 3.8" WC (0.95 kpa)
Orifice Size 31 DMS
Minimum Input 20,000 Btu/h (5.86 kW)
Maximum Input 38,000 Btu/h (11.13 kW)
PROPANE GAS FIREPLACE INSERT: MODEL E33-LP10
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. Supply Pressure 12" WC (2.99 kpa)
Low Setting Man. Pressure 2.9" WC (0.72 kpa)
Max. Manifold Pressure 11" WC (2.74 kpa)
Orifice Size 50 DMS
Minimum Input 19,000 Btu/h (5.56 kW)
Maximum Input 35,500 Btu/h (10.4 kW)
Alcove Width E 76" (1930mm)
Alcove Depth F 36" (914mm)
Non-Combustible Hearth Extension
Hearth Height G 1-1/4" (32mm)
Hearth Width H 45-1/2" (1156mm)
Hearth Depth I 13" (330mm)
* Alcove side wall must have a
min. of 8” clearance on one side.
4001172
Listed: VENTED GAS FIREPLACE HEATER
/ FOYER AU GAZ À ÉVACUATION
Certified for/Certifi e pour: CANADA and U.S.A.é
Certified to: CAN/CGA-2.17-M91(R2009)
Tested to: ANSI Z21.88-2014 & CSA 2.33-2014
For Use Only with Barrier (Part # 342-013) With Low Profile or (Part n ° 342-049) Installed with Vignette Follow installation instructions.
Utiliser uniquement avec l’écran ( n° 342-013) avec Profile Bas ou ( n° 342-049) Install avec Vignette. Suivre les instructions d'installation.

10 | E33-10 FPI Direct Vent Gas Insert
|
10 requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)