Remootio 3 User manual

Remootio 3 installation manual
Thank you for choosing Remootio 3!
Step 0 - Unboxing
Open the box and remove the Remootio device. The wires, double-sided adhesives and
the sensor can be found under the removable paper insert.
Your Remootio 3 kit contains the following items:

•A- 1 x REMOOTIO 3 unit
•B- 1 x Sensor (wired part | 4m / 13.12Ft)
•C- 1 x Sensor (wireless part)
•D- 2 x Double-sided adhesives for mounting the sensor
•E- 1 x Double-sided adhesives for mounting the Remootio unit
•F- 1 x Power cord (USB A to barrel jack | 1 m / 3.28 feet)
•G- 1 x Control wire (1 m / 3.28 feet)
•H - 1 x Installation manual
•I - 1 x Bottom part of packaging
•J- 1 x Top part of packaging
•K- 1 x USB charger (depending on where you order from, the product is shipped with
type A (US), type C (EU), type G (UK) or type I (AUS) charger.
Read the instruction manual carefully and follow
the instructions
The printed instruction manual can be found on the back side of the paper insert.
Before you begin, make sure that the circuit breaker of the gate or garage door is
switched off and there is no power in the system.
Step 1 - Remove the plastic cover
Use a cross head screwdriver to remove the screw from the Remootio unit and remove the
plastic cover.

Remootio 3 pinout diagram:
1. control output 1 (normally open relay)
2. control output 2
(normally open relay)
3. power input
5-32VDC | 12-24VAC
min. 100mA
4. add-on input 1
(e.g. sensor input)
5. add-on input 2
(e.g. doorbell button input)
6. reset button
7. fuse
8. feedback LED
9. power OK LED
Step 2 - Wiring the control output
Connect the control output of the Remootio unit to the appropriate input terminals of your gate
or garage door. In some cases, there is only one input pair (single input) and in other cases
there are two input pairs (dual input) on the control board that has to be triggered to open or
close the gate or garage door.

Based on the type of required control input, there are two types of gates and garage doors:
•A single signal (impulse) can open, stop and close the gate or garage door
•Two separate signals (impulses) needed:
oOne signal for opening
oand another signal for closing.
Enter the make and model number of your gate or garage door below to search for the correct
wiring diagram.
Single input type:
Use the included pair of wires to connect Remootio's control output to the appropriate input
terminal of your garage door / gate control board. One of the leads need to be wired to the
"0V", "GND" or "COM" terminal and the other lead to "CYC", "IMPULSE", "IMP", "KBUTT",
"OPERATE", "OSC", "PB", "PP", "SBS", "SS", "START", "STRT", "SW", "TRG", "WALL BUTTON" or
"WALL CONTROL" depending on the manufacturer's naming convention.
(The outputs are polarity independent, which means that within the same output terminal, the
order of the wires does not matter).
Please visit https://www.remootio.com/pages/compatibility and enter the make and model of
your gate or garage door to search for the correct wiring diagram.

Note: The color of the wires may be black or white.

Dual input type (separate input for opening and closing):
Connect Remootio's output #1 to the "open" input terminal of your gate or garage door control
unit and connect Remootio's output #2 to the "close" input terminal of your gate or garage
door control unit. If you have a gate or garage door opener that needs both outputs to be wired
to the control board, please go to the settings menu of Remootio and select "output
configuration" and please choose the "Output 1: output to open | Output 2: output to close"
option.
For more details about the output configuration, please visit this article.

(The outputs are polarity independent, which means that within the same output terminal, the
order of the wires does not matter).

Step 5 - Sensor installation
Connect the sensor to terminal 4 of the Remootio 3 unit and use the included adhesives to
mount the wireless part of the sensor on the moving part of the gate or garage door in such a
way that it is not further than 30mm from the wired part of the sensor when the gate or garage
door is closed.

For more details and images about about the sensor installation, please check our sensor
installation tutorial. When enabling the sensor interface in the app, please make sure to select
the corresponding input (in this example "input 1").
Step 3 - Connecting an accessory
You can connect a manual control button or a doorbell button to terminal 5 of the Remootio
board. (The inputs are polarity independent, which means that within the same input terminal,
the order of the wires does not matter).

Step 4 - Assemble the Remootio unit back together
Use a screwdriver to assemble the Remootio unit. Make sure that you do not damage the wires
during the assembly.
Apply the double-sided tape on the back side of Remootio as shown below: