REMOTE WORLD MERLIN E945M User manual

MERLIN E945M 3 BUTTON
REMOTE PROGRAMMING INSTRUCTIONS
remoteworld.com.au
•
•
•
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.
ALWAYS keep gate or garage door in sight until completey closed. NEVER permit anyone to cross path of moving gate or door.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
Single Button Remote Control
Model E940M
3-Button Remote Control
Model E943M
Press and hold the button on
the remote control or wireless
wall control you wish to use. The
LED indicator on
the transmitter
continuously
(except E945M).
Locate
the learn
button. Press and
immediately release
the Learn button.
For use with Security 2.0 Garage Door Openers. The code between the
the remote control and the receiver changes with each use, randomly
accessing over a billion new codes. Refer to your product manual for the
location of the learn button.
NOTE: Your product may look than the products illustrated
in this manual.
LED
LED
+
ROLLER DOOR
OPENER
LEARN
BUTTON
3- Button Mini Remote Control
Model E945M
Wireless Wall Control
Model E128M
“click”
“click”
The opener
or 2 clicks are
heard when
it has learnt
the code.
4
LED
LED
INDICATOR
SECTIONAL DOOR
OPENER
LEARN
BUTTON
LED
INDICATOR
4-Button Remote Control
Model E950M
LED
LED
Wireless Wall Control
Model E138M
PROGRAM USING THE GARAGE DOOR OPENER

remoteworld.com.au
MERLIN E945M 3 BUTTON
REMOTE PROGRAMMING INSTRUCTIONS CONT.
•
•
•
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play with remote controls.
ALWAYS keep gate or garage door in sight until completey closed. NEVER permit anyone to cross path of moving gate or door.
Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.
When deactivating any unwanted remote
control code, all previous codes will be
erased. Press and hold the Learn button on garage door opener
until the learn LED goes out (approximately 6 seconds).
All previous codes are now erased. Reprogram each
remote control you wish to use.
TO ERASE ALL CODES FROM MEMORY

remoteworld.com.au
MERLIN E945M 3 BUTTON
REMOTE PROGRAMMING INSTRUCTIONS CONT.
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
.rotcodyfitonyletaidemmi,dewollawssiyrettabfI•
To reduce risk of explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
.etarenicniro)C°001(F°212evobataeh,elbmessasid,egrahcerTONOD•
The lithium battery should produce power for up to 5 years. If the battery is low, the remote control's LED will
not when the button is pressed. To replace battery:
REPLACING THE BATTERY
CR2032
Use a screwdriver
blade to pry open the
case as shown
Remove the old battery.
Dispose of old batteries
properly.
Insert replacement
batteries positive side
up. Replace the
batteries with only
CR2032 coin cell
batteries.
Replace cover.
Press and hold the button down until the door or gate
starts to move. The remote control will operate from
up to 3 car lengths away on typical installations.
Installations and conditions vary, contact an installing
dealer for more information.
CR2032 Lithium battery - CR2032
Additional buttons on the remote control can be
programmed to operate up to 3 devices such as
additional garage door openers, light controls, gate
operators or access control systems.
REPLACEMENT BATTERY TYPE
WHAT ARE THE ADDITIONAL BUTTONS FOR?
HOW TO USE THE REMOTE CONTROL