Reshable MR11S0229 User manual

User Manual
Model Number：MR11S0229

Dear Customer,
a. Theouter boxisdamaged.
c. Theparts/accessories/assembly tools are missing.
b. Theproduct isdamaged/bent/cracked whileyou open thebox.
e. Theinstructions are not clear and can notbe referred to.
f. Theproduct has functional problems.
g. Other aspects that you are not satisfied with.
d. Theproduct ishard to assemble.
Thankyouforyour purchase.
RESHABLEiscreatedtobetheperfect startingspot forany barbers. Supplyingtop-quality
barber supplies like barber chairs, salon stations, rolling makeup cases, styling drawer
cabinets, hair tool holders, and more, we help people to keep their barber store running
with thebest equipment at themost reliable prices.
Whenyou receive theproduct,pleasemake sure thatall the parts are intact. Thenplease
browsetheentire installation manual before assembly. If problemsoccur unsatisfactorily
as follows:
Please do not hesitate to contact us for help (Be sure to mark the SKU NUMBER, e.g.,
MR11R0246, and the TRACKING NUMBER). Our RESHABLE team with factory direct
after-salesservicewill replywithin24 hoursanddoour best to resolve theproblem foryou.
Our serviceis available at any time.
Sincerely,
RESHABLE Team
RESHABLE
for Profession and Creativity!
2
1
You need
22 persons are needed
A wrench & an
allen key are
required for the
assembly of the
product. (not included)
1Tools required
Backrest
Seat
Footrest support
Footrest
Base
Pump
Foot bar
Seat Cushion
Backrest connector

3 4
NOTICE:
If your package or part of the package is lost, or you have problem
installing, please call us directly or leave us a message,Our
customer service team will address any questions or concerns
you may have.
This user manual is for your reference.
SAFETY:
To reduce risks of injuries when installing & using the chair, follow
these precautions:
·Read all of these instructions before installing and using your
salon chair.
·It is helpful to have 2 people install and turn the chair upright
after installing.
·Do not exceed the maximum weight capacity of the salon chair,
which will result in a risk of falling off or make the chair tip.
Exceeding number of recommended user would also result in
injuries.
Hardware List
１ＰＣ
Ｓｅａｔ
Ｐｕｍｐ
１ＰＣ
Ｂａｃｋｒｅｓｔ
Ｆｏｏｔ ｂａｒ Ｂａｓｅ
１ＰＣ
Ｓｅａｔ Cushion １ＰＣ
Ｆｏｏｔｒｅｓｔ
１ＰＣ １ＰＣ １ＰＣ
2ＰＣＳ
Ｂａｃｋｒｅｓｔ ｃｏｎｎｅｃｔｏｒ 2ＰＣＳ
Ｆｏｏｔｒｅｓｔ ｓｕｐｐｏｒｔ
６ＰＣＳ
Black bolt

6
5
PRODUCT ASSEMBLY
PRODUCT ASSEMBLY
STEP 2
STEP 1
Check the package contents before getting started !
Seat ２ＰＣＳ
Ｂａｃｋｒｅｓｔ ｃｏｎｎｅｃｔｏｒ
Ｐｕｍｐ
Ｆｏｏｔ ｂａｒ １ＰＣ Ｂａｓｅ １ＰＣ １ＰＣ
First:Install pump to the base
Step 1.Install the pump to the base with the 6 black bolts .
Step 2. Place assembled Base & Pump on the floor.Use Allen
Wrench to loosen the screws in the crossbar. As shown in the
picture . Insert Foot Bar into the holes of the crossbar.(It is
required to stress ends of the foot bar against each other, andthe
bar will be fixed to the corresponding place.)
Step 3.Tighten the 2 setscrews until the foot bar is firmly
fixed and stable.
Second:Install backrest connectors to the seat
Step 1.Remove the 4 pre-installed bolts on the 2 sides of the
armrest.
Step 2.Install 2 backrest connectors to both sides of the
armrest with overall 4 bolts (2 bolts for each side).
Ｂｌａｃｋ ｂｏｌｔ ６ＰＣＳ
1PC
Note: Please refer to the picture for the assembly direction of the
foot lever. Do not install it in the wrong direction.

1ＰＣ
8
7
PRODUCT ASSEMBLY
PRODUCT ASSEMBLY
STEP 4
STEP 3
Third:Install backrest connectors to the seat
Step 1.Remove the 4 pre-installed bolts on the 2 sides of the
armrest.
Step 2.Install 2 backrest connectors to both sides of the armrest with
overall 4 bolts (2 bolts for each side).
Fourth:Install footrest supports to the footrest
Step 1.Install the 2 footrest supports to the footrest .
Ｂａｃｋｒｅｓｔ ２ＰＣＳ
Ｆｏｏｔｒｅｓｔ ｓｕｐｐｏｒｔ
１ＰＣ
Ｆｏｏｔｒｅｓｔ