Response SAURC Installation manual

Press and hold the top two buttons, Instant
-Arm and Disarm simultaneously or
approximately 15 seconds until the LED
indicator begins to lash.
The SAURC Remote Control is now ready
or programming.
1. Place your original Remote Control
BACK to BACK with your new Universal
Remote Control (SAURC).
2. Programme each button/ unction as
ollows:
INSTANT-ARM
Simultaneously press and hold the
Instant-Arm Button on both Remote
Controls until the LED indicator on the
SAURC begins to lash rapidly indicating
that the Instant-Arm Button has been
success ully programmed.
DISARM
Simultaneously press and hold the
Disarm Button on both Remote Controls
until the LED indicator on the SAURC
begins to lash rapidly indicating that the
Disarm Button has been success ully
programmed.
PART-ARM/DELAY-ARM
Simultaneously press and hold the
Part-Arm/ Delay-Arm Button on both
Remote Controls until the LED
indicator on the SAURC begins to
lash rapidly indicating that the Part-
Arm / Delay-Arm Button has been
success ully programmed.
PERSONAL ATTACK
Activate the Personal Attack Switch on
the original Remote Control by pushing
it up and holding whilst simultaneously
depressing the Personal Attack Button
on the SAURC.
Transmit LED
Indicator
Universal Remote Control (SAURC)
Programming Instructions
Part 1: Prepari g the SAURC for Programmi g
Part 2: Programmi g
Slide up
to operate
Transmit
LED
Personal
Attack
Disarm
Instant-Arm
Part-Arm/
Delay-Arm*
Personal
Attack
Disarm
Instant-Arm
Part-Arm/
Delay-Arm*
IMPORTANT: When programming place both Remotes BACK to BACK and make
sure the battery in your original Remote is fully serviceable.
Transmit
LED
* Part-Arm with Control Unit systems or
Delay-Arm with Siren only systems
Both Remotes must be
aligned at the top edge
SAURC Ed3_Universal Re ote Control_Instructions_Art:-) 12/09/2014 22:46 Page 1

Respo se Electro ics Ltd.
Roman House, Lysons Avenue, Ash Vale, Surrey GU12 5QF
Email: [e-mail]
Web: www.responseelectronics.com
Tech ical Support Helpli e:
0345 257 1000
(Local Call Rate - lines open 09.00 to 17.00 Monday to Friday)
SAURC Ed.3
Troubleshooti g
• Ensure the battery in your original
Remote Control is in a ully serviceable
condition.
• Keep the two Remote Controls back to
back throughout programming.
• I programming is not success ul repeat
Part 1 and Part 2.
• I , a ter two attempts, programming has
ailed then attempt programming in a
di erent physical location, this will rule
out the possibility o it being due to local
Radio Frequency inter erence in your area .
For advice and support please call our
Customer Support Helpline (details below)
or email [e-mail].
Disposal a d Recycli g
Disposal o this product
is covered by the Waste
Electrical or Electronic
Equipment (WEEE) Directive.
It should not be disposed o with other
household or commercial waste.
At the end o its use ul li e the packaging
and product should be disposed o via a
suitable recycling centre. Please contact
your local authority or the retailer rom
where the product was purchased or
in ormation on available acilities.
Tech ical Specificatio s
Application: Response SA 433 MHz Alarms
Operating frequency: 433 MHz
Battery type: 12V 27A Alkaline
Battery life: 1 year (typical)
Antenna type: Internal
Transmitting distance: up to 75 metres
(open space clear line o sight)
Colour: Black with Chrome inish
Programming: Fast – copy enabled
Dimensions: 52 x 32 x 8 mm
Warranty: 1 year parts and labour
Manufacturing: High-quality SMT Manu actured
Certification: CE, R&TTE, FFC Compatible (2)
Guara tee
The product is guaranteed or one year rom the date o purchase against aulty materials and
workmanship. No liability can be accepted or any problems caused by air wear and tear, buyer’s
negligence, improper itting or use, wil ul or accidental damage, or any consequential loss or
damage howsoever caused. This guarantee does not a ect your statutory rights and is valid or
UK and EIRE only.
I you believe the product to be aulty or in the unlikely event o the product developing a ault
during the warranty period, then please contact our Technical Support Team (contact details
shown below) or product assistance. Product repair or replacement will be o ered or aulty
products only with our prior agreement. Should you need to return a products then:
1. Contact the Help Line on the number below to obtain a Return Authorisation Number.
2. Adequately package your product to prevent damage in transit and include
the ollowing:
a. A copy o your original invoice/receipt.
b. A covering letter giving your ull contact details, including email address
(i applicable).
c. A description o the ault or problem.
SAURC Ed3_Universal Re ote Control_Instructions_Art:-) 12/09/2014 22:46 Page 2