Revolabs REVOLABS SOLO 02-DSKSYS Operating instructions

I
II
Installation and Operation
nstallation and Operation nstallation and Operation
nstallation and Operation
Guide
GuideGuide
Guide
Revolabs Solo™ Single Channel
Wireless Microphone System
Models 02-DSKSYS, 04-DSKSYSEU
Revolabs, Inc.
Revolabs, Inc.Revolabs, Inc.
Revolabs, Inc.
© 2007 REVOLABS, INC. All rights reserved. No part o this
document may be reproduced in any orm or by any means
without express written permission rom Revolabs, Inc.
Product speci ications are subject to change without notice.
R e v o l a b s S o l o ™ S i n g l e C h a n n e l
0 2 - D S K M A N - P A P - 1 1
D e c e m b e r 2 0 0 7 ( R e v . 1 )

Table of Contents
Safety and General Information.....................................................1
Introduction ....................................................................................4
System Components .....................................................................5
Revolabs Solo™ Single Channel Charger Base ...........................5
Mute Button ...............................................................................6
Power Module ...........................................................................6
USB Connection........................................................................6
External Audio Connection........................................................6
Installing the Solo Single Channel System....................................6
Computer Software Set-up........................................................7
Revolabs Solo™ Wireless Microphones .....................................12
Using with Wearable Wireless Microphone.............................12
Using with TableTop Microphone............................................14
Using with XLR Microphone Wireless Adapter .......................15
Using with a Solo Executive Multi-channel System ................18
Charging the Batteries.............................................................18
When to Charge ......................................................................18
Setting the Broadcast Power Level .........................................19
Pairing the Microphone to the Charger Base ..........................20
LED Status Indications ................................................................22
Warranty ......................................................................................23
Solo Single Channel Specifications .............................................24
1
Safety and General Information
This section contains important information regarding safe and efficient
system operation, and declarations of required certification / regulation
compliance. Please read this information prior to using your Revolabs
system.
FCC User Information and Notice
FCC Registration Number: 0014898290
FCC ID Number: T5V02DSKSYS Revolabs Charger
FCC ID Number: T5V01EXEMIC Revolabs Microphone
Users are not permitted to make changes or modify the equipment in any
way. Changes or modifications not expressly approved by Revolabs, Inc.
could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Federal Communications Commission (FCC)
Radiation Exposure Statement
Important: This equipment complies with FCC radiation exposure limits
set forth for an uncontrolled environment.
Industry Canada Notice to Users
Operation is subject to the following two conditions: (1) This device may
not cause interference and (2) This device must accept any interference,
including interference that may cause undesired operation of the device
Ref IC: RSS 210 Sec. 5.11. The term “IC:” before the certification /
registration number signifies that registration was performed based on a
Declaration of Conformity indicating that Industry Canada technical
specifications were met. It does not imply Industry Canada approval of
the equipment. See Ref IC Self-Marking 6(f) and RSP-100 Sec. 4.
IC ID Number: 6455A-02DSKSYS Revolabs Solo™ Desktop Charger
IC ID Number: 6455A-01EXEMIC Revolabs Solo™ Microphone
Restricted use with certain medical devices
Hearing Aids
Some devices may interfere with some hearing aids. In the event of such
interference, you may want to consult with your hearing aid manufacturer
to discuss alternatives.

2
Other Medical Devices
If you use any other personal medical device, consult the manufacturer of
your device to determine if it is adequately shielded from RF energy.
Your physician may be able to assist you in obtaining this information.
Export Law Assurances
This product is controlled under the export regulations of the United
States of America and Canada. The Governments of the United States of
America and Canada may restrict the exportation or re-exportation of this
product to certain destinations.
For further information contact the U.S. Department of Commerce or the
Canadian Department of Foreign Affairs and International Trade. The use
of wireless devices and their accessories may be prohibited or restricted
in certain areas. Obey the laws and regulations on the use of these
products.
02-DSKSYS North America UPCS Usage
Restriction
Due to the UPCS frequencies used, this product is licensed for operation
only in the United States of America and Canada.
04-DSKSYSEU European Union Usage Restriction
Due to the frequencies used, this product is licensed for operation only in
the European Union countries.
European Compliance
This equipment has been approved in accordance with Council Directive
1999/5/EC “Radio Equipment and telecommunications Equipment.”
Conformity of the Equipment with the guidelines below is attested by the
CE mark.
Model Numbers:
04-DSKSYSEU-BLK-11 Revolabs Charger
03-EXEMICEU-BLK-11 Revolabs Executive Microphone
05-TBLMICEU-OM-BLK-11 Revolabs Solo™ Table Microphone Omni
05-TBLMICEU-DR-BLK-11 Revolabs Solo™ Table Microphone Cardioid
Standards to which Conformity is declared:
RF ETSI EN 301 406 V 1.4.1 03/2001
EMC ETSI EN 301 489-6 v1.2.1 (2002-04)
3
WEEE Notification:
The Waste Electrical and Electronic Equipment (WEEE) directive
(2002/96/EC) is intended to promote recycling of electrical and
electronic equipment and their components at end of life.
2003/11/EC & 2002/95/EC “RoHS Compliance Directive”:
The products referenced herein are in compliance with the EU
directive 2003/11/EC and EU directive 2002/95/EC.

4
Introduction
IntroductionIntroduction
Introduction
Congratulations on the purchase o your Revolabs
Solo™ Single Channel wireless microphone system!
This wireless system provides high band-width audio
rom a compact wireless microphone enabling
reliable, secure, and untethered personal
communication.
The Single Channel Wireless Microphone System is a
unique marriage o innovative technology and
ergonomic stylish design, eaturing 1.9 GHz DECT
technology. This product enhances audio
communication in both personal and enterprise
applications, using Multi-Carrier, Time Division
Multiple Access and Time Division Duplex
(MC/TDMA/TDD) radio transmissions both to and
rom the microphone.
This means that the system can co-exist with other
wireless products such as wireless LANs (802.11 b&g)
and cellular phones.
Note: It is recommended that no more than 3 Single
Channel Systems, nor a Single Channel and
Multichannel System, be used in the same room to
avoid interference.
5
System Components
System Components System Components
System Components
Your Revolabs Solo™ Single Channel System package
contains:
•Compact Charger Base
•Solo Wireless Microphone (varies)
•Power Module
•External Audio Cable
•USB cable
•Installation and Operation Guide
•Solo Single Channel Quick Start Guide
Revolabs
Revolabs Revolabs
Revolabs Solo
SoloSolo
Solo ™
™™
™ Single Channel
Single Channel Single Channel
Single Channel Charger Base
Charger Base Charger Base
Charger Base
Use the Charger Base to store and charge the
Microphone when not in use. The Microphone must
be properly inserted into the base and seated lush or
charging to occur.
1. Charger Bay — charges Microphone
2. LED indicator — mute and pairing status indicator
3. MUTE button — duplicates the Microphone mute function
4. AUDIO port — 2.5mm analog in/out external audio
connection
5. Mini USB connector — computer audio connection
6. POWER connector — power supply input

6
Mute Button
Pressing the MUTE button toggles between muting
( lashing RED LED status) and un-muting ( lashing
GREEN LED status) on the Wireless Microphone.
Note: Press the MUTE button on a Microphone will
similarly toggle between mute and un mute and
display on both status LEDs.
Power Module
The Charger Base requires 5VDC power. Plug the
supplied AC adapter into a convenient 110-240VAC,
50-60Hz power outlet and the adapter into the power
connector.
USB Connection
Use the supplied cable to connect the mini USB
connector to the Charger Base and the standard end
to your computer USB port.
External Audio Connection
The Single Channel System includes a cable or
connecting the Charger Base to an external audio or
con erencing system. The provided 2.5mm miniplug-
to-RCA cable allows the microphone’s unbalanced
line level audio to be used with a mixer or
con erencing system using the RCA male jack. Output
rom the mixer or con erencing system can be
connected to the RCA emale plug providing audio to
the microphone’s earpiece. An optional Line-to-mic
level cable (07-STEMIC-PPP) is available or purchase.
Install
InstallInstall
Installing the Solo Single Chann
ing the Solo Single Channing the Solo Single Chann
ing the Solo Single Channel System
el Systemel System
el System
The Revolabs Solo™ Single Channel system is easily
installed into either the o ice or con erence room
environment. Simply plug the power supply into a
convenient outlet and attach the USB cable to a
computer or laptop, or connect the 2.5mm audio
cables to an audio system. Power is not provided by
the USB cable.
7
Computer Software Set-up
Use the supplied USB cable to connect the mini USB
connector to the Charger Base and the standard end
to your computer USB port. Your computer will alert
you that it has ound a new USB device.
It is possible to con igure your computer settings to
playback audio through the earpiece attached to the
Wearable microphone (de ault settings) or through the
computer speakers (internal or desktop).
The ollowing examples use the Microso t Windows
®
XP Operating System Classic settings. You may notice
slight di erences in appearance when using other
Windows operating systems.
To modi y the de ault microphone earpiece audio
output settings:
1. At the lower-right o your screen, click the Start
button.
2. Select Settings and Control Panel.
3. Click the Sounds and Audio Devices icon.

8
The Sounds and Audio Devices Properties dialog will
display, as shown. The solo-Desktop device will be
selected.
9
4. Open the Volume settings or Sound recording
to view the volume levels selected or the
microphone input (Capture) on the computer.
5. Make sure that the level or the Microphone is
close to the top (maximum) and that the Mute
box is not checked.
6. In the Sound playback section, open the
Volume settings or to control the volume you
hear in the Microphone’s earpiece.
Adjust the Speaker level at the master Volume
control i necessary.

10
7. At the bottom o the Microphone section, click
the Mute box in the Microphone section to
prevent the Microphone directly eeding back
its own audio to the earpiece (i.e. “sidetone”).
It may be necessary to use the Options-
Properties menu to display the Microphone
volume control.
IP telephony and computer telephony
applications (e.g., Skype) may also o er options
or controlling the audio levels and playback
capabilities. Please consult the application
guide or the so tware package or additional
instructions.
8. Change the Sound playback De ault device to
your regular audio codec (SigmaTelAudio in
this example) to playback audio through the
internal or external speakers o the computer
instead o the earpiece.
9. At the bottom o the dialog, click Apply, and
then click OK.
Note: Laptop computers with built in microphones
may continue to operate even when the solo Desktop
software is running. To prevent the built in microphone
audio feeding through to the speakers, check the Mute
box on the laptop audio program Input Monitor, as
shown below.
11

12
Revolabs Solo™ Wireless Microphone
Revolabs Solo™ Wireless MicrophoneRevolabs Solo™ Wireless Microphone
Revolabs Solo™ Wireless Microphones
ss
s
Using with Wearable Wireless Microphone
The wireless personal microphone uses encrypted
communication to synchronize with the Charger
Base. It provides high quality ull duplex audio
between the user and the computer, audio or video
con erence system or external audio system. The
system allows the wearer to step out o the o ice or
con erence room and still participate in the call.
1. Microphone port — direct toward mouth for best audio pickup.
2. Noise cancelling port — do not block opening.
3. Mute Button — press to mute, un-mute and pair microphone.
4. Pocket clip — also used to attach microphone to lanyard.
5. LED display — visual status for mute, un-mute, and pairing.
6. Earpiece jack — accepts the 2.5mm plug for the earpiece.
7. Charging port — docks to Solo Charger Bases.
Note: Microphones in new systems must be paired
to the Charger Base. See microphone pairing
instructions on page18.
Revolabs Solo™ Wearable Microphones turn on and
mute automatically when removed rom Charger
Base, to reduce noise while being attached. The
microphone has a clip on the back which allows the
microphone to be easily attached onto a shirt pocket,
blouse, lapel or lanyard.
To use the Wearable Microphone:
13
1. Remove the microphone rom the Charger Base.
The double- lashing RED LED on the Microphone
and Charger Base con irm that the mic is paired
and muted.
2. Attach the microphone to clothing or to a lanyard
close to the mouth, within 6-12 inches (15–30cm)
is recommended. Make sure microphone is
attached securely with the microphone port
pointed up toward mouth.
3. With the microphone in the wearing position, un-
mute the microphone by pressing and releasing
the Mute button (con irm by viewing lashing
GREEN LED). I the volume is too low, move the
microphone closer to the mouth.
4. To turn microphone o , return the Microphone to
the Charger Base. The Microphone LED will show
a 5 second sel -test pattern and begin charging
(solid RED or GREEN LED). Alternately, turn o
the Microphone manually by pressing and holding
the Mute button or 10 seconds, until the LED
turns solid RED, then release the mute button and
the LED will turn OFF.
I the microphone is moved out o range o the
Charger Base (~65 eet or 20m) the connection will be
dropped (LED lashes all colors) and the microphone
will mute.
A ter 15 seconds the microphone will beep 5 times,
and will continue beeping every 30 seconds to remind
the user to return the microphone to the con erence
room. I the microphone is moved back into range
within 15 minutes the connection will automatically
be re-established to its original state, and the beeping
will cease. I not, the microphone will turn o .
Ad usting the Volume
Ad usting the VolumeAd usting the Volume
Ad usting the Volume on
on on
on the Wearable Microphone Earpiece
the Wearable Microphone Earpiecethe Wearable Microphone Earpiece
the Wearable Microphone Earpiece
To change the volume on the Wearable microphone
earpiece, use the dial on the earpiece wire.

14
Turning the dial towards the earpiece, as shown in
the igure, will increase the volume, and turning
the dial towards the microphone will decrease the
volume. Use the attached clothing clip to secure
the earpiece wire.
Using with TableTop Microphone
The Revolabs Solo™ TableTop Wireless Boundary
Microphones enable multiple phone con erence
participants to use a single microphone. Units are
placed strategically on the con erence table to ensure
that all participants can be heard clearly.
1. Mute Button — press to mute, un-mute and pair microphone.
2. LED display — visual status for mute, un-mute, and pairing.
3. Integral grille — protects internal parts (non-removable).
4. Audio jack — accepts a 2.5mm plug for a powered speaker.
5. Charging port — docks to all Solo Charger Bases.
6. Rubber feet — non-slip, vibration absorbing pads.
To use the Wireless TableTop Microphone:
1. Remove the microphone rom the Charger Base.
The microphone turns on and mutes automatically
when removed rom Charger Base ( lashing RED
15
LED), to reduce noise while placing the
microphone on the table.
2. TableTop microphones should be centered on the
table with the integral grill pointed toward the
users (uni-directional), or centrally located
between users (omni-directional), rom 2 to 5 eet
(.75 to 1.75m) away. It is always better to be as
close to the person speaking as possible, but avoid
placing the microphone where it might be blocked
by equipment or meeting paperwork. Also do not
place microphones too close to an audio or video
con erence speaker to avoid echoes.
3. With the microphone in position, un-mute the
microphone by pressing and releasing the MUTE
button (con irm by viewing lashing GREEN LED).
4. To turn microphones o , return the microphone
unit to the Charger Base. The Microphone LED
will show a 5 second sel -test pattern and begins
charging (solid RED or GREEN LED). Alternately,
press and hold the MUTE button or 10 seconds
until the LED turns solid RED , then release the
mute button and the LED will turn OFF.
I the microphone is moved out o range o the
Charger Base (~65 eet or 20m) the connection will be
dropped (LED lashes all colors) and the microphone
will mute.
A ter 15 seconds the microphone will beep 5 times,
and will continue beeping every 30 seconds to remind
the user to return the microphone to the con erence
room. I the microphone is moved back into range
within 15 minutes the connection will automatically
be re-established to its original state, and the beeping
will cease. I not, the microphone will turn o .
Using with XLR Microphone Wireless Adapter
The Revolabs Solo™ Universal Wireless Adapter or
Handheld Microphones, shown in the ollowing igure,
is connected to your existing handheld dynamic

16
microphones or wireless reedom during open mic
meetings, Q&A sessions, classrooms, etc.
7.1. Mute button — press to mute, un-mute and pair
microphone.
8.2. Rubber collar — durable and impact/strain protection.
9.3. XLR Female connector — balanced audio for dynamic
microphones.
10. 4. LED display — visual status for mute, un-mute,
and pairing.
11. 5. Audio Out port — accepts the 2.5mm plug for
the earpiece.
6. Power/Charging Port — docks to all Solo Charger
Bases.
To use the Revolabs Solo™ Universal Wireless
Adapter:
5. Remove the Microphone Adapter rom the Charger
Base.
The adapter turns on and mutes automatically
when removed rom Charger Base ( lashing RED
LED). The XLR Microphone Adapter is attached to
a standard dynamic microphone to convert it rom
a wired microphone to a wireless microphone (see
ollowing igure).
17
The Adapter does not provide phantom power or
bias current so it cannot be used with condenser
or electret microphones.
6. With the microphone attached, un-mute the
Adapter by pressing and releasing the Mute button
(con irm by viewing lashing GREEN LED).
Note: If the microphone has an on board mute
switch, this switch must also be un muted prior to
use.
7. To turn the Adapter o , return the microphone
unit to the Charger Base or press and hold the
Mute button or ~10 seconds until the LED turns
solid RED and release button.
Important: Always remove the microphone rom
the Adapter by pressing the latch switch and
separating the parts be ore returning the Adapter
to the Charger Base.
I the microphone is moved out o range o the
Charger Base (~65 eet or 20m) the connection will be
dropped (LED lashes all colors) and the microphone
will mute.
A ter 15 seconds the microphone will beep 5 times,
and will continue beeping every 30 seconds to remind
the user to return the microphone to the con erence
room. I the microphone is moved back into range
within 15 minutes the connection will automatically

18
be re-established to its original state, and the beeping
will cease. I not, the microphone will turn o .
Using with a Solo Executive Multi-channel System
The Revolabs Solo™ Single Channel Wearable
Microphone can be paired to a Solo Executive Multi-
channel Wireless Microphone System or users who
wish to have a single microphone to use in both the
o ice and in the con erence room. This is
accomplished by pairing the Single Channel Wearable
Microphone to the Executive Multi-channel Base
Station and docking the Microphone in the Executive
Charger Base. The Microphone can then be used in
either system by placing the Microphone in the
respective Charger Base or about 5 seconds.
Charging the Batteries
To charge the batteries place the Microphone into the
Single Channel Charger Base. During charging, the
Microphone status LED indicator changes rom solid
RED to solid GREEN as charging completes. The
Charger Base status indicator remains o during
charging. The Microphone is always muted while in
the Charger Base. The battery charges rom ully
depleted to ully charged in approximately two hours,
however, it is “quick-charged” to 80% capacity in 45
minutes.
Note: A fully charged battery provides approximately
8 hours of talk time.
When to Charge
Be ore using the Microphone or the irst time, charge
or 8 hours or overnight in the Charger Base (until
microphone LED turns solid GREEN).
When the Microphone LED begins lashing alternating
YELLOW and RED or YELLOW and GREEN, the
battery needs recharging. Over time (years), batteries
gradually wear down and require charging a ter a
shorter period o use. This is normal.
19
Important: The Lithium Polymer rechargeable battery
that powers the Microphone is not user serviceable.
Please see the Revolabs website ( www.revolabs.com ) or
in ormation regarding battery replacement and proper
disposal procedures. Warning: Exposing the
batteries to fire may result in an explosion.
Setting the Broadcast Power Level
In con ined settings where multiple Solo Executive
Single Channel systems are used, or where audio
inter erence is likely, it may be necessary to reduce
the broadcast power levels.
The broadcast power level between the Microphone
and Charger Base can be set to the ollowing three
levels.
•Highest power level – 60 eet (25M) maximum
operating distance between Microphone and
Charger Base (de ault setting).
•Medium power level – 20 eet (7M) maximum
operating distance between Microphone and
Charger Base.
•Lowest power level – 6 eet (2M) maximum
operating distance between Microphone and
Charger Base.
To set the broadcast power level:
Press and hold the Mute button while plugging the
USB cable into the Charger Base.
The status LED on the Charger Base will display a
sequence o lashes, during which it will lash once,
then twice, then three times, where:
1 GREEN lash = ull power
2 GREEN lashes = medium power
3 GREEN lashes = low power.
This cycle will repeat 10 times. During any o the
cycles, simply release the Mute button immediately
a ter the desired power indication, to set the

20
Executive Single Channel system broadcast/receive
power.
Pairing the Microphone to the Charger Base
“Pairing” creates an encrypted association between
the Wireless Microphone and the Charger Base with a
unique electronic serial number. When the
Microphone and Charger Base have been previously
paired, the Microphone will automatically try to
connect to the Charger Base whenever it is li ted rom
the Charger Base.
Note: The Microphone in new systems will need to be
manually “paired” prior to first use.
I a Microphone is li ted rom the Charger Base and
the Microphone LED slowly lashes alternating RED
and GREEN or 10 seconds, it means that the
Microphone needs to be paired to the system.
To pair the Microphone to the Charger Base:
1. Make sure the Microphone is turned OFF (no LED
activity). I the unit is ON, press and hold the
MUTE button or 10 seconds until the LED turns
solid RED then release. Alternately, place the
Microphone in the Charger Base or less than 2
seconds.
2. Enable the pairing mode by holding the
Microphone’s Mute button down or eight seconds.
The LED will turn solid GREEN and then solid
RED. Release the Mute button. The Microphone
unit is now in pairing mode.
3. Push and hold the Charger Base’s Mute button or
eight seconds to enter into pairing mode then
release.
4. The LED will be solid RED until pairing is
complete, as indicated by double lashing RED on
both the Microphone and the Charger Base (paired
and muted audio). I pairing ails at the end o one
minute on either unit, the LED will lash
21
alternately GREEN and RED or a ew seconds and
turn OFF. I this happens, repeat these steps.

22
LED Status Indications
LED Status IndicationsLED Status Indications
LED Status Indications
The ollowing LED patterns are shown on either the
Microphone or the Charger Base.
LED Pattern Meaning
Solid GREEN
(Microphone only*)
Confirmation of power-up or battery
reaching full charge. * In earlier versions
LED will turn OFF when fully charged.
Solid RED Pairing mode, or confirmation of powering-
down, or battery charging.
GREEN flash every 1.5
seconds
Microphone paired, connected and un-
muted.
Two RED flashes every
1.5 seconds
Microphone paired, connected and muted.
YELLOW flash
alternating with GREEN
flash
Microphone paired, connected, un-muted
and battery low.
YELLOW flash
alternating with two RED
flashes
Microphone paired, connected, muted and
battery low.
Alternating RED,
YELLOW, GREEN,
YELLOW (Microphone
only)
Searching for a connection, or out of radio
range. The Microphone will try to re-
establish the link for about 15 minutes, and
then turn off automatically. The Microphone
will beep five times every 30 seconds.
Alternating slow RED
and GREEN
Microphone is not paired to Base Station.
Rapid RED flashes
continuing for more than
a few seconds
Radio congestion – it is not possible to
make a radio connection because there are
already too many nearby users, or there is
heavy radio interference. Interference may
be caused by some types of digital cordless
phones, and other Revolabs Solo™
installations.
Groups of five rapid red
flashes
Unit is faulty. Please contact your place of
purchase for advice on return.
23
Warranty
WarrantyWarranty
Warranty
Revolabs, Inc. warrants this product to be free of manufacturing
defects. Repair or replacement of any defective part or unit (at the
discretion of the Seller) will be free of charge for the period of 90
days.
Any attempt by the user to alter the equipment, or equipment
damaged by negligence, accident, or Acts of God voids this
warranty.
The Seller shall not be liable for any consequential damage
resulting from the malfunction of this product. Should the user
experience unsatisfactory performance from this equipment,
contact the Seller to obtain instructions for return, or replacement,
as deemed necessary.
This warranty is not transferable by the original end user.
Revolabs, Inc.
63 Great Road
Maynard, MA 01754
www.revolabs.com
1-800-326-1088

24
Solo
Solo Solo
Solo Single Channel
Single ChannelSingle Channel
Single Channel Specifications
Specifications Specifications
Specifications
Dimensions, (L, W, H) and Weight
Single Channel Charger Base
3.9” (10 cm) x 2.4” (6 cm) x 1.0” (2.56 cm), 0.5 lb (0.23 kg)
Wearable Microphone:
0.9” (2.3 cm) x 0.8” (2.0 cm) x 2.6” (6.6 cm), 0.05 lb (0.02 kg)
TableTop Microphone:
1.5” (3.8 cm) x 0.8” (2.0 cm) x 3.3” (8.4 cm), 0.05 lb (0.02 kg)
XLR Adapter:
0.9” (2.3 cm) x 0.8” (2.0 cm) x 4.0” (10.2 cm), 0.05 lb (0.02 kg)
Shipping Weight
1.5 lbs (0.68 kg)
Radio Frequency
02-DSKSYS - 1.92 to 1.93 GHz (UPCS North America)
04-DSKSYSEU - 1.88 to 1.90 GHz (DECT EU)
Connectors
Single Channel Charger Base
Power – 5VDC, proprietary 0.7mm connector
Mini USB – 5 pin connector, USB 2.0
Audio unbalanced In/Out – 2.5mm
Tip: Audio Out (line level, 0dBV)
Ring: Audio In (line level, 0dBV)
Shield: GND
Wireless Microphone
Power – proprietary 4 pin connector
Audio – 2.5mm mono audio
Microphone patterns Executive unidirectional – cardioid.
TableTop omni-directional and uni-directional available.
Power Requirements
Power Adapter 110 - 240VAC, 50-60Hz to 5VDC, 300mA
Battery Lithium Polymer, up to 8 hours talk time
Charge Time 2.0 hours approx.
Range 65’ (20 meters) approx. (no obstructions)
Audio Bandwidth 100-7000 Hz
Encryption 128-bit DSAA (DECT Standard
Authentication Algorithm) authentication,
64 bit DECT Standard Cipher
Environmental Requirements
Temperature 40°to 105°F (5°to 40°C) operating
Humidity 20% to 85%
25
R e v o l a b s S o l o ™ S i n g l e C h a n n e l
0 2 - D S K M A N - P A P - 1 1
D e c e m b e r 2 0 0 7 ( R e v . 1 )
Note:
Microphon
es must be fully charged
and paired to the Charger Base
prior to first use.