Revoltec Cardmagic User manual

User’s Manual

REVOLTEC CARDMAGIC

USB 2.0 Card Reader/Writer with 3-port Hub

for

CompactFlashTM Card Type I & II, IBM MicrodriveTM,

Memory Stick®, Memory Stick PRO®,

MultiMediaTM Card, SecureDigitalTM Card,

SmartMediaTM Card, xD Picture Card

Table of Contents

Introduction……………………………………………………….…….…1

Package Contents….…………………………..……….………..…1

Safety Instructions…….….…………..……………………...……1

Specification……………….…..………………………………...…..…2

SystemRequirements………………..………………………..…..3

Driver Installation………………………...…………………..…....3

AP System Installation…….……………………………..….…10

Installation Verification…………..……………………….…….15

Check the System for USB 2.0 Hub……………………17

Product Details.……………………….. …………………..………19

Over-Current Status Figure……….………………………..21

Certificate………….…………………….……………………….………22

Introduction

Thank you for purchasing our REVOLTEC CARDMAGIC USB 2.0 card reader/writer

with built-in USB hub. Our card reader/writer allows you to read, write, and erase data

from the most popular cards such as CompactFlashTM Card Type I & II (CF Type I & II),

IBM MicrodriveTM, Memory Stick ® (MS), Memory Stick PRO®(MS PRO),

MultiMediaTM Card (MMC), SecureDigitalTM Card (SD), SmartMediaTM Card (SM),

and xD** Picture Card. The USB 2.0 hub allows you to add multiple USB 2.0 peripheral

devices to your PC and your USB 1.1 devices can function as usual. This device is

small, light, easy to carry, and easy to use.

**Not all types of Card Reader/Writers support xD Picture Card. Please

check the package or the vender for the xD card support.

Package Contents

· USB Card Reader/Writer with 3-port Hub

· Power Adapter

· USB Cable (optional)

· Driver CD

· Quick Installation Guide

Safety Instructions

1. Always read the safety instructions carefully.

2. Keep the User’s Manual for reference.

3. Keep the equipment away from humidity.

4. Lay this equipment on a reliable flat surface before setting it up.

5. If any of the following situations arises, please contact a service technician for

diagnostics:

· The equipment has been exposed to moisture.

· The equipment has been dropped or damaged.

· If the equipment has obvious sign of breakage.

· The equipment has not been working well or it is still not functioning after you refer

to the User’s Manual.

Specification

USB 2.0 Card Reader/Writer

· Four slots:

· CF Type I & II/ Microdrive………………………..…….…1

· MS/ MS PRO…….…….……………… ……….….…...………1

· SD/ MMC….…………………………………...….………....…….1

· SM or SM/ xD**………………………………………...……....1

· Compliant with Hi-Speed USB 2.0 CompactFlash, Memory Stick, MultiMedia,

SecureDigital, Smart Media Standard Specifications

· Transfer rate: 480 Mb/sec (maximum)

· Hot-Swapping allowed between all cards

· True plug-and-play function

· No driver needed for Windows ME/2000/XP

**Not all types of Card Reader/Writers support xD Picture Card. Please

check the package or the vender for the xD card support.

USB 2.0 Hub

Power:

· Bus-power: 5V 500mA

· Self-power: 5V 2.5A

· Adapter: Input: 100~240V 50Hz-60Hz

Output: 5V 2.5A

· Compliant with Universal Serial Bus Specification Revision 2.0 (Data Rate

1.5/12/480 Mbps)

· Connects up to 127 USB devices

· Over-current detection and protection

· True plug-and-play function

· 1 upstream and 2/4 downstream USB ports included

· 1 red LED as power-on indicator (In some models, there is a green LED indicator for

each downstream port apart from the red LED)

· Storage temperature: -10~85 °C

· Working temperature: 0~40 °C

USB Power Port (optional)

Apart from the 3 standard USB ports, there is a USB Power Port in some models that

is a value-added function of USB Hub. It is an ideal solution for powering some USB non-

data-transmitting devices such as USB lamps, USB messagers, USB mobile phone

chargers, etc. This socket-like USB Power Port supplies power up to 500mA.

Notice: The USB devices with data-transmitting function cannot work with USB Power

Port.

System Requirements

· IBM Compatible PC or Mac with available USB port

· With one of the following operating systems:

· Windows® 98/SE

· Windows® ME (no driver needed)

· Windows® 2000 (no driver needed)

· Windows® XP (no driver needed)

· Mac 9. X

· Mac 10. X

Driver Installation

Except Win 98SE and Mac system, the driver of card reader/writer is bundled on the

OS Win ME, Win 2000, and WinXP. Please follow the instructions step by step until the

installation is completed.

Win 98SE：

1. When the wizard searches for new drivers for USB 2.0 device, click ‘Next’.

2. Select ‘Search for the best drivers for your device [Recommended]’, and then

click ‘Next’ to continue.

3. You may either select ‘CD-ROM drive’ or ‘Specify a location’ (click ‘Browse’ to

select the driver for Windows 98 in our CD-ROM driver). Click ‘Next’ to

continue.

4. When the system is ready to install the driver, click ‘Next’ to continue.

5. Once the system has finished installing the software for the new driver, click

‘Finish’ to complete the first installation.

6. As step 1, the wizard searches for another new driver. Click ‘Next’ to continue.

7. As step 2, select the best driver for your device and click ‘Next’ to continue.

8. As step 3, select either ‘CD-ROM drive’ or ‘Specify a location’. Click ‘Next’ to

continue.

9. As step 4, when the system is ready to install the driver, click ‘Next’ to

continue.

10. Once the system has finished installing the software for the new driver, click

´Finish’ to complete the first installation.

11. Check ‘My Computer’ to make sure the four icons of CF, SM, SD, and MS of the

AP system is shown (see the next section for the AP system installation).

AP System Installation

If the four icons of the ‘Removable Disk’ are not specified, you need to install the

software from the driver CD for setting up the AP system. The procedures are listed

below:

Windows ME/2000/XP

1. As the picture shown, no ‘Removable Disk’ is marked. Please click the drive icon

of ‘RU3141 (F:)’ (“F” is the location of your CD drive).

2. Click the driver folder for Windows.

3. Click ‘Setup’ to start the installation.

4. Select your language and click ‘OK’.

5. Click ‘Next’ to install the system.

6. Click ‘Finish’ to complete the installation.

7. Select ‘Yes’ click ‘OK’ to restart your computer.

8. Please check ‘My Computer’ to confirm the icons of CF, SM, SD, MS of the AP

system.

Mac 9.X

1. Please insert the CD-driver to CD-ROM and there is a CD-ROM image on the

desktop.

2. Click the image of CD-ROM, and copy “GENEUSB.sit” to the desktop.

3. Click “GENEUSB.sit“ and copy “install.sit“ to the desktop. It will generate an image

“GENEUSBML.2“.

4. Find the files like file of 9.0.4 later and 8.6-9.0, and then click the choice of the file.

5. Click the “INSTALLER”.

6. The icon “Restart Your Computer After Installing” will show up and please click

”CONTINUE” to restart the computer.

Notice：If you have installed the older version driver, you must remove it before

installing the new one. Please delete these files:

/ System Folder/ Extensions/ Gene USB ML Driver.

/ System Folder/ Extensions/ Gene USB ML Shim.

Installation Verification

Win98SE/ Win ME

Win2000/ WinXP

Mac 9.X/ Mac 10.X

MAC 9.X: After installation finished, please click Apple image of the menu bar and

select “Apple Device”. Click “Devices and Volumes” to display the USB

Card Reader.

MAC 10.X: After installation finished, please click “Apple System Profiler” and select

“Devices and Volumes”. Click “USB“ to verify the installation.

Check the system for USB 2.0 hub

After connecting the product to your PC/Mac, the system will detect the USB hub and

install the required drivers automatically. You can check Device Manager to verify the

completed installation.

· The device name maybe varied on your host driver.

· The Power Port is not included in the USB hub function.

Windows 98SE:

Windows ME:

Notice: If the operating system is Windows ME, a green question mark may be shown in

‘Device Manager’. It is all right because Windows ME cannot identify the USB Hub's

brand but there is no influence on its function.

Windows 2000:

Windows XP:

Product Details

Connects to PC or Mac

Type B Receptacle

Type A Plug

Power jack:Connects to Power Adapter

5V / 2.5A

USB 2.0 Card Reader/Writer

* The models with SM slot do not support xD Picture Card.

CF/Micro Drive

MS/MS PRO

SD/MMC

SM* SM/xD

USB 2.0 Hub

Downstream: Connect to Devices

X 3

Type A Receptacle

USB Power Port (optional)

X 1

The isolator is red

Over-Current Status Figure

 When the excessive current

happens, the power will be

disconnected from the related port.

The green LED goes off.

 If there is a pop-up window, “ USB

Hub Current Limit Exceeded “,

please click Reset to resume. You

can also reset the hub by

unplugging the USB cable and

plugging it back.

Mac OS:

After installation finished, please go to “Apple System Profiler\ Devices and

Volumes\USB” to verify the installation completed.

Certificate

FCC

This equipment has been tested and found to comply with Part 15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference

(2) This device must accept any interference received. Including interference that may

cause undesired operation.

CE – Certificate

This equipment is in compliance with the requirements of the following regulations: EN

55 022: CLASS B

Table of contents

revoltec CARDMAGIC User manual

Popular Card Reader manuals by other brands