RFI CSA10-41-DIN User manual
ASSEMBLY INSTRUCTIONS
COMPONENTS
Before assembling your antenna please ensure that all the components below are included in the kit.
148-174 MHz
CSA10-41-DIN
M-8569
CENTRE SCREEN
QTY: 1
M-8569
SIDE SCREENS
QTY: 2
CORNER BRACKET
QTY: 8
M8x80 (3" LONG)
HEX HEAD BOLT
M8 FLAT WASHER
M8 FLAT WASHER
M8 SPRING WASHER
M8 HEX NUT
M8x80 BOLT ASSEMBLY
QTY: 16
M8 FLAT WASHER
M8 SPRING WASHER
M8 FLAT WASHER
M8x130 (5" LONG)
HEX HEAD BOLT
M8 HEX NUT
M8x130 BOLT ASSEMBLY
QTY: 2
M-8648
DIPOLE ASSEMBLY
QTY: 1
SMALL CLAMP PLATE
QTY:1
M16x250 (10" LONG)
THREADED ROD
M16 FLAT WASHER
M16 HEX NUT
M16 SPRING WASHER
M16 STUD ASSEMBLY
QTY: 4
LARGE CLAMP PLATE
QTY: 2
INS-40094-1 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 1 OF 4
148-174 MHz
SIDE SCREEN
SIDE SCREEN
CENTRE SCREEN
M8x80 BOLT ASSEMBLY
CORNER BRACKET
M-8648
DIPOLE ASSEMBLY
CENTRE SCREEN
SMALL CLAMP
PLATE
M8x130 BOLT
ASSEMBLY
240
MM +/-2MM (9.5")
SET DIPOLE POSITION
DRAIN HOLE
CSA10-41-DIN
ANTENNA ASSEMBLY
STEP 1:
ASSEMBLE SIDE SCREENS TO CENTRE SCREEN AS PICTURED BELOW USING THE M8 BOLT ASSEMBLY AND
CORNER BRACKETS INCLUDED IN THE KIT. TIGHTEN M8 BOLTS TO 25NM (19 lbf.ft)
STEP 2:
ASSEMBLE THE DIPOLE TO THE CENTRE SCREEN AS DEPICTED BELOW ENSURING THE DIPOLE TO SCREEN
SPACING IS SET CORRECTLY AND THE DIPOLE DRAIN HOLE IS FACING DOWNWARDS.
USING THE SMALL CLAMP PLATE AND THE 2 M8 x 130 HEX BOLT ASSEMBLIES INCLUDED IN THE KIT.
TIGHTEN THE M8 BOLTS TO 25Nm (19 lbf.ft)
INS-40094-1 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 2 OF 4
148-174 MHz
CSA10-41-DIN
CENTRE SCREEN
M16 THREADED BAR
ASSEMBLY
Approx. 150MM
Approx. 150MM
MOUNTING TUBE
(NOT INCLUDED)
LARGE CLAMP PLATE
$17(11$02817,1*+$5':$5(+$6%((1
'(6,*1('72$&&(3702817,1*78%(
',$0(7(56,17+(5$1*(2)PP
02817,1*78%(/(1*7+72%(6,=('%<
,167$//(57268,7,167$//$7,210(7+2'
3/($6(127(02817,1*32/(1276833/,('
INS-40094-1 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 3 OF 4
ASSEMBLY INSTRUCTIONS continued
STEP 3:
FIT THE 4 M16 THREADED ROD ASSEMBLIES TO THE CENTRE SCREEN AS DEPICTED BELOW.
LEAVE APPROXIMATELY 150mm (6") PROTRUDING OUT THE BACK SIDE. TIGHTEN TO 70Nm (50lbf.ft)
STEP 4:
WITH THE ANTENNA ASSEMBLY LOCATED ON THE MOUNTING TUBE ATTACH THE 2 LARGE CLAMP PLATES
AND TIGHTEN THE M16 NUTS CLAMPING THE ANTENNA ASSEMBLY TO THE MOUNTING TUBE. TIGHTEN TO
70Nm (50 lbf.ft)
148-174 MHz
CSA10-41-DIN
SCREENED ARRAY ASSEMBLY
CSA-10-41-DIN
TOWER
TOWER CLAMPS
MOUNT POLE
OUTRIGGER
STRAIN RELIEVE FEED CABLE BACK
TO SUPPORT STRUCTURE.
SEAL CONNECTOR WITH A SUITABLE
SELF AMALGAMATING TAPE.
TYPICAL
INSTALLATION
SIDE VIEW
SCREENED ARRAY IS DESIGNED TO BE
FIXED TO A TOWER MOUNTED POLE OR
TOWER LEG.
ENSURE THAT MOUNTING POLE,
CLAMPS AND MOUNTING STRUCTURE IS
APPROPRIATELY SIZED TO SUIT LOCAL
WIND AND ICE INSTALLATION
CONDITIONS.
ASSEMBLY INSTRUCTIONS continued
TYPICAL INSTALLATION
INS-40094-1 ©RF Industries Pty Ltd 2009
www.bird-technologies.com
PAGE 4 OF 4
Table of contents
