RFRemotech AlphaFire X Series User manual

Safe, Easy and Reliable,With remote controllable service.AlphaFireXSeries(9thGeneration)User'sManual1234567810911120.10.20.30.40.50.60.70.81.00.92.0ALL

ContentsWarning!!!A.FiringModuleA1.PartsA2.SpecificationA3.HowtoInsert/RemoveBatteryA4.3-PositionSwitch#2A5.LowPowerIndicationA6.LEDIndicator#4A7.TestB.Transmitters/RemotesB1.TransmitterAB2.TransmitterBC.Synchronization(SYNC)C1.BeforeSYNCC2.SynchronizeTransmitterAC3.SynchronizeTransmitterBC4.CheckSynchronizationC5.DeleteSynchronizationD.FireD1.ManualFiringD2.SequentialFiringThanks!------------------------------------------------------------------------1----------------------------------------------------------------1-----------------------------------------------------------------------1-------------------------------------------------------------2---------------------------------------2----------------------------------------------------2--------------------------------------------------2---------------------------------------------------------3-------------------------------------------------------------------------3----------------------------------------------------4-------------------------------------------------------------4-------------------------------------------------------------4-----------------------------------------------------5--------------------------------------------------------------5---------------------------------------------5---------------------------------------------5-------------------------------------------------6------------------------------------------------6-----------------------------------------------------------------------------6------------------------------------------------------------7--------------------------------------------------------7

Warning!!!A. The purpose of this device is to cause the ignition of fireworks. Fireworks are explosives and may cause personal injuries or death to yourself or others, including spectators. You are responsible for the safe and legal use of this device according to the laws and regulations of your country and/or state / province / district. RFRemotech is not responsible for illegal or unsafe use of this device. The buyer/user assumes all responsibility and liability in the use of this device and further agrees, by purchase and/or use of this device, to indemnify and hold harmless RFRemotech against all liability for injury, loss, or damage direct or consequential arising out of the use of, or inability to use this device.A.FiringModuleB. If the marked LED Indicator above keeps turned RED but not dim red on whenever the rod of the 3-Position Switch is at OFF, SYNC-TEST or ARM, don't use the module any more, the unit will igniters randomly. It is dangerous and may do damage to body!A1.Parts112345671-forigniters/e-matches.WiringTerminalsRedforanode,blackforcathode.2-,OFF/SYNC-TEST/ARM.3-PositionSwitch3-.UsedforsynchronizationorSYNCButtondeletingsynchronization.4-,twocolorsredandgreen.LEDIndicator5-,retractileandcanbefolded.Antenna6-.Encloser7-.BatteryCoverC. This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ModelNo.:RF1XG9Power:1x9Vbattery,6LR61or6F22orothers>750mA,Max.9AFiringCurrent:<1mATestCurrent:1ohm,<700mALowPowerIndication:L62xH46xW38mm,antennaisretractileandcanbefoldedSizes:A2.Specification2A3.HowtoInsert/RemoveBatteryItisspeciallydesignedtocheckifthebatteryispowerfulenoughtofireanigniter.Ifthebatteryistoolow,theDIMRedLEDwillblink.Thecheckingresultisjustforreference.Ifusersuseasensitiveigniter,itcanstillfirethoughtheDimRedisblinking.Onthecontrary,Ifusersuseigniterswhichrequiremorecurrenttofire,thoughtheDimRedisnotblinking,thefiringwillprobablystillfail.Insert BatteryRemove BatteryA5.LowPowerIndication:Power/LowPowerIndication,FiringIndication,RFSignalIndication,OverloadProtection,ShortWarningIndicationSYNC-TEST:Tocheckiftheconnectionofigniter/e-matchisingoodcondition,see“Test”below,orpresstheSYNC-TESTbutton#3tosynchronizeordeletetransmitters.Readytofireigniter/e-match.Thereare2firingmodesselectable.ARM:See“E.TwoFiringModes”below.A4.3-PositionSwitch#2:

A7.TestWhenthefiringmoduleispoweredandanigniterisconnectedtoWiringTerminals#1,shift3-PositionSwitch#2toSYNC-TEST,LEDIndicator#4willbelitgreen,otherwisetheigniterisbrokenorthewiresarenotconnectedwell.OnlywhentheconnectionistestedOK,theignitercanfiresuccessfully.-RedandGreen.TwoColorLED-Aheavycurrentisflowingout.Itappearswhen3-PositionSwitch#2isRedatARMandthemoduleisfiringorthemoduleʼscircuitisshort.-Itappearswhen3-PositionSwitch#2isatSYNC-TESTpositionDimRedandnoigniterisconnectedortheigniterisbroken.-ItappearswhenthepowerischeckedlowtofireanBlinkingDimRedigniter.-When3-PositionSwitch#2isatSYNC-TESTandtheigniteristestedGreenOK.-Themoduleiscountingthefiringsequence.BlinkingGreen-RedandGreenareoninthesametime,armedandreadytofire.OrangeItappearswhen3-PositionSwitch#2isatARM.A6.LEDIndicator#4:3

B.Transmitters/Remotes1234567810911120.10.20.30.40.50.60.70.81.00.92.0ALLManual FiringTransmitterA(12buttons)SequentialFiringTransmitterBNormallyitisa1,2,4or12buttondevice,everybuttoncanfireitsmatchingfiringmodules.Buttonshavenumerals1,2,…,12orlettersA,B,C,Drespectivelyorblank.4Manual FiringTransmitterA(1button)Thetransmitters/remotesneedtobewiththefollowingfeatures:OOKModulation;433.92MHz;LearningCode.Afiringmodulecanworkwith2typesoftransmitter/remote:B1.TransmitterA-ManualFiringTransmitterItisa12buttondevice,thebuttonshavemarks0.1,0.2,…,0.9,1.0,2.0andALLrespectively,Button0.1canfiremultiplefiringmodulesonebyoneinintervaltime0.1second,Button0.2canfirein0.2secondsetc.,whenButtonALLispressed,theintervaltimeiszero.B2.TransmitterB-SequentialFiringTransmitter:

C.Synchronization(SYNC)Usersshouldbeawareofthefollowinginformationordosomeoperationslikebelow.It'sbetterusersdothestep“DeleteSynchronization”belowinthefiringmodulebeforesynchronization.Onlywhenatransmitter/remotehasalreadybeensynchronizedtoafiringmodule,thebothcanworktogether.IfTransmitterBissynchronizedbutTransmitterAisnotyet,theTransmitterBwillnotfunction.AfiringmodulecanstorecodesofoneButtonofTransmitterA,oneTransmitterB.Ifuserssynchronizethesametypeoftransmitter/remoteandbutton,theformertransmitter/remoteandbuttonwillbereplaced.Shifttherodof3-PositionSwitch#2ofthefiringmodulefromOFFtoSYNC-TEST,pressanddon'trelease#3SYNC-TESTbuttonmorethan3secondsuntilLEDIndicator#4islit,thenpressonebuttonofTransmitterAwithin3seconds,LEDIndicator#4willblinktwiceandthengobacktothestatebeforedoingSYNC,thebuttonofthetransmitter/remoteissynchronizedtothefiringmodulesuccessfully.Shifttherodof3-PositionSwitch#2ofthefiringmodulefromOFFtoSYNC-TEST,pressanddon'trelease#3SYNC-TESTbuttonmorethan3secondsuntilLEDIndicator#4islit,thenpressanybuttonofTransmitterBwithin3seconds,LEDIndicator#4willblinktwiceandthengobacktothestatebeforedoingSYNC,thetransmitter/remotehasbeensynchronizedtothefiringmodulesuccessfully.5 Thebuttonʼsnumeralofthetransmitter/remoteisalsorememberedasthewhenthemoduleisimplementingSequentialSequencingNumberFiring.C2.SynchronizeTransmitterAC1.BeforeSynchronizationC3.SynchronizeTransmitterB

Shifttherodof3-PositionSwitch#2fromOFFtoSYNC-TEST,1-IfButton5ofTransmitterAisalreadysynchronizedtothefiringmodule,pressButton5ofthetransmitter,theLEDIndicator#4willblinkonce.ItindicatesButton5issynchronized.Thesamewithotherbuttons.2-Aftertheformerstepisdone,pressButton0.7ofthesynchronizedTransmitterB,theLEDIndicator#4willblink5timesinintervaltime0.7seconds.ItindicatestheTransmitterBissynchronized.Shifttherodof3-PositionSwitch#2fromOFFtoSYNC-TEST,pressanddon'treleasebuttonSYNC-TEST#3morethan6seconds,theLEDIndicator#4willbelit,donʼtreleaseyetuntiltheLEDblinkstwiceandgoesbacktothestatebeforepressingbuttonSYNC-TEST#3,allstoredcodesoftransmittersarecleared.D.Fire6Beforefiring,youneedtomakesurefollowing:Firing ModuleRemoteIgniterFireFiring CommandsFiringmodulesandtransmitters/remotesarepoweredwell,nooneofthemhasLowPower.Theseunitsarealreadysynchronized.IgnitersareconnectedwellandtestedOK.Theantennasofthemodulesandtransmitters/remotesshouldbepulledandextendedout.Itʼsbetterifthefiringmodulesareplacedintheheight1.5mormoreabovetheground.Therodof3-PositionSwitch#2isatARM.Thedistancefromthetransmitter/remotetothemodulesmustbelessthantheonesmarkedonthetransmitters/remotes,thenmorethan0.5m.C4.CheckSynchronizationC5.DeleteSynchronization

123456781091112Manual FiringTransmitterAMode1:ManualFiringUseTransmitterA,pressthecorrespondingbuttonStofirethematchingmodules.0.10.20.30.40.50.60.70.81.00.92.0ALLSequentialFiringTransmitterBMode2:SequentialFiring7UseTransmitterB,pressButton0.1tofirethematchingmodulesatthecorrespondingSequencingNumbers1,2,3,...inIntervalTime0.1s;Button0.2inIntervalTime0.2s,thesamewithotherbuttons.123789456101112ThisdiagrammeansTransmitterBandthebuttonsofTransmitterAarealreadysynchronizedtothecorrespondingmodulesrespectively.

Manufacturer:RFRemotechE-mail:[e-mail]Http://www.RFRemotech.comAugust,20218Thanks for using RFRemotech products!