RGMT BATTLEDRESS User manual

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.

Restart and stop of the stopwatch can be repeated
by pressing the button A.
ACCUMULATED ELAPSED TIME
MEASUREMENT
STOPRESET
START STOP RESTART
Measurement and release of split time can be
repeated as many times as necessary by pressing
the button B.
SPLIT TIME
MEASUREMENT
STOPRESET
START SPLIT SPLIT
RELEASE
ADJUST THE CHRONOGRAPH HANDS
TO ZERO POSITION
Example:
One or several chronograph hands are not in their
correct zero positions and have to be adjusted (e.g.
following a battery change).
1, Unscrew and pull out the crown to position
[3]-(2nd click). (all chronograph hands are in
their correct or incorrect zero position).
A
B
3. Adjusting the second counter hand:
Single step, push button Aonce
Continuous. push & hold button Along
To adjusting the next hand push button B
2. Keep push-buttons A and B depressed simultane-
ously for at least 2 seconds (the second counter
hand rotates by 360º corrective mode is
activated).
A
B
INSTRUCTION MANUAL
BEDIENUNGSANLEITUNG
IM.RGMT.CO
For more details on operating this timepiece
please refer to the enclosed booklet or visit :
CHRONOGRAPH WATCH
This timepiece is equipped with a
sWISS MADE CHRONOGRAPH movement.
28
MINUTE HAND
HOUR COUNTER
PUSH
BUTTON A
PUSH
BUTTON B
SCREW-DOWN
CROWN
CHRONOGRAPH
SECOND HAND
CHRONOGRAPH
60 MINUTE
HAND
HOUR HAND
DATE
(MOV’T RONDA 5030.D)
SMALL
SECOND HAND
WATER RESISTANCE
Note that the water resistance chart serves only as a
guide (please refer to the water resistance chart on the
next page). Actual water resistance may vary depending
on a number of factors including water temperature,
water salinity, and use under water.
The water resistance of your timepiece may eventually
be compromised over time with general wear and tear
and use of your timepiece under adverse conditions.
Always remember to employ the screw down crown if
available to maintain the water resistance of your
timepiece. Warranty may be voided if the screw down
crown has not been properly employed.
Note that you should never wear your watch in a jacuzzi
or steam room where steam may enter the case despite
the water tight seals used to protect your watch. This
may cause condensation inside your watch which may
effect and damage the inner workings of your watch.
100M/
10ATM
WATER RESISTANCE
CHART
SPLASH/
SHOWERING
SWIMMING/
BATHING
BRIEF SWIMMING/
WATER SPORTS
PROLONGED
SWIMMING/
FREE DIVING
SCUBA
DIVING
PROFESSIONAL
DEEP SEA DIVING
4. Adjusting the minute counter hand (position 9h):
Single step, push button Aonce
Continuous. Push & hold button Along
Push the crown back and screw down in the
position [0] to terminate the chronograph hands
adjustment.
A
B
3
PLEASE READ THE FOLLOWING
BEFORE UNSCREWING THE CROWN:
SCREW-DOWN CROWN
Screw-down crowns are used to ensure water
resistance. ALWAYS be certain that your crown is
securely screwed down ( Position [0] is secured.
Positions [1], [2] and [3] are not secured for water
resistance ).
Do NOT unscrew your crown while you are in any
environment where moisture is present.
0 1 2
(1st click) (2nd click)
CLOSED
Securely screwed
+ Water Resistance
OPENED
Not secured
For Water Resistance
USING THE SCREW-DOWN CROWN
DO NOT PULL THE CROWN UNLESS IT IS
FIRST:
NOTE: Failure to SECURELY screw down the crown
after setting the watch may affect its water
resistance.
TO UNSCREW: Turn the
crown anti-clockwise until it
turns freely without tension.
GENTLY pull the crown out to
the other desired positions for
watch setting (see specific
operating instructions on the
following pages).
TO SCREW: Push the crown
ALL THE WAY IN (towards the
watch) THEN begin to turn
clockwise until it is securely
screwed down.
HOW TO SET THE TIME
1. Pull out the crown to the position [3]-(2nd click).
(the watch stops).
2. Turn the crown until you reach the correct time.
3. Push and screw down crown back in the
position [0].
HOW TO SET THE DATE
1. Pull out the crown to the position [2]-(1st click).
(the watch continues to run).
2. Turn the crown until the correct date appears.
3. Push and screw down crown back in the
position [0].
Please note: The date can be changed during the date
changing phase between approx. 9:00 PM and 12:00
PM; please note that the date must be set to the date
of the following day as in this case the automatic date
changing does not occur at midnight.
STOPWATCH FUNCTION
• The stopwatch measures up to 10 hours.
STANDARD MEASUREMENT
START STOP RESET
0
1
12
3
BATTLEDRESS
Vol. 1.04A EN DE
4 5 6
7
UNI-DIRECTIONAL
TURNING BEZEL
HOW TO CHANGE THE STRAPS TO
NATO STRAP
1. 2.
HOW TO ATTACH THE STRAPS
3.
0 1 2
28
3
28
A
B
0 1 2
28
3
3.
4.
5. 6.
7.
8.
9.
1. 2.