TasmanEco Urban Ancona User manual

RECYCLED
1
Urban collection
Assembly Instruction
Packaging and instructions
printed on recycled materials
SJC Brands Pty Ltd abn. 58 106 988 578
4-6 Merryvale Rd, Minto, NSW 2566 p.o. box 5878 Minto, DC, NSW 2566
t. 02 9603 5000 f. 02 9603 7000
e. [email protected]
w.www.tasmaneco.com.au
Ancona 3 Drawer Chest
Assembly of this furniture is best undertaken by two people.
Made in China
This product has been independently tested and complied with:
AS/NZS 4935:2009 Domestic furniture - Free standing chests of drawers, wardrobes and booksheleves/ Bookcase Determination
of stability & AS/NZS 8124.3:2012 + A1:2016 Migration of certain elements.

Hardware List
Handle x 6 Camlock x 36
M6 x 35mm Bolt x 4 Allen key x 1 Wall strap x 1 M4 x 25mm Self-tapping screw x 2
Assembly tips
for hardware
Warning
Re-check tightness
Re-tighten all connector bolts ( at least two months after assembling the chest),
as some connectors may loosen as the chest settles. Periodically check all of the
connector screws making sure they are tight.
Screws
We recommend tightening all screws and connectors by hand. If using a cordless
driver, set the speed to a slow setting and clutch to a low setting to prevent
excessive tightening that may result in damage to your furniture.
Small parts can present choking hazard. Always keep small parts out of reach of children
both during and after assembly. Store any spare or unused parts in a safe place.
E
M4 x20mm Screw x12 Locking pin x36

Part Checklist
Side panel x 2 Front bottom rail x 1 Back middle rail x 1
Back bottom rail x 1 Top board x 1 Back panel x 2
Drawer side panel (left) x 3 Drawer side panel (right) x 3 Drawer back panel x 3
Drawer front panel x 3 Drawer base panel x 3
?

Locking pin x 12
4
Fit locking pins to side panels.
Fit front bottom rail, back middle rail,
back bottom rail to one side panel secure
with camlocks.
Insert back panel sliding into
groves on back middle rail and
back bottom rail.
Camlock x 6

5
Fit other side panel to rails secure with
locking pins and camlocks.
Insert back panel sliding into groves
on two side panels.
Place top board onto chest frame
secure with M6 x 35mm bolts.
M6 35mm bolt x 12
Tighten all bolts and screws by allen
key but do not over tighten.
Allen key

6
Locking pin x 4
Fit locking pins to
drawer side panels.
Fit side panels to drawer
back panel secure with
camlocks.
Insert base sliding into groves on
side panels.
Fit locking pins into front
drawer panels.
Locking pin x 4
Align the drawer front panel secure with
locking pins and camlocks.
Place drawer handles in position
and secure with M4 x 20mm bolts
from inside.
Insert drawers, the chest is completed.
M4 x20mm Screw x4

7
Wall Wall
you room to screw the wall strap into the wall

8

Urban collection Guarantee
SJC Brands Pty Ltd ABN. 58 106 988 578
4-6 Merryvale Rd , Minto , NSW 2566
PH: 02 9603 5000 FAX: [phone]
.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
The guarantee described below is in addition to the guarantee provided by law.
2 YEAR MATERIALS AND WORKMANSHIP GUARANTEE
If within 2 years of the date of purchase of this product, there is found any defect in materials or workmanship of this product, SJC
Brands Pty Ltd will replace the product free of charge, subject to the condition below:
The replacement product will be identical to the originally purchase product wherever possible, though in situations where the
identical model is discontinued or out of stock, then SJC Brands Pty Ltd will replace the product with a model that is functionally
equivalent
This Guarantee is made to the purchaser and/or original owner only. For purposes of this Guarantee, the original owner is
considered to be the person who first makes use of the product.
Note: In situations where a person purchases this product for the purpose of gifting to another, the recipient is considered to be the
original owner.
CONDITIONS:
The 2 Year Material and Workmanship Guarantee will be void and nullified in circumstances where:
1.The item is improperly assembled or adjusted and or not assembled strictly in accordance with the written instructions provided
by the seller in the box containing the item.
2.There is damage to the product and that damage is deemed by SJC Brands Pty Ltd to be caused by incorrect assembly, misuse
or by use or storage outside of the physical or environmental specifications of the product.
3.There are modifications to the product or to parts of the product that were not authorized in writing by SJC Brands Pty Ltd.
4.The item is transferred, gifted or disposed of by the original owner to another.
WARRANTY CLAIM PROCEDURE:
For warranty claims, please email us via our claims section on our website www.tasmaneco.com.au or visit the store where the
product was purchased.
The product must be returned to SJC Brands Pty Ltd or to the place of purchase with proof of purchase, including date and
purchase price.
w.www.tasmaneco.com.au
Email: customer[email protected]