EVIE C RYSTAL SC O NCE - ASSEMBLY I N S T RUC T I O N S
Page 2 of 2
(A) Back Plate (1)
(B) Glass Shade (1)
(C) Socket (1)
All wires are connected.
Do not remove the fixture from its packing by pulling on the power cord,
as a bad connection may result.
Do not connect electricity until your fixture is fully assembled.
To reduce the risk of fire, electrical shock, or personal injury, always turn
off/unplug fixture and allow it to cool prior to replacing lightbulb.
Do not touch bulb when fixture is turned on or look directly at lit bulb.
Keep flammable materials away from lit bulb.
PARTS ENCLOSED:
WARNINGS:
IMPORTANTSAFETY INSTRUCTIONS:
WARNINGS: STRANGULATION HAZARD
Keep cord at least 3 feet away from cribs, bassinets, and toddler beds.
Keep out of reach of children under three years of age.
DIRECT-WIREASSEMBLY &INSTALLATION:
CAREINSTRUCTIONS:
Do not use polishes or cleaners on the fixture.
Wipe clean with a soft, dry cloth.
1. Carefully remove all parts from the box and remove all plastic coverings.
2. Shut off power at the junction box where the sconce will be installed.
3. Cut the cord that comes through the hole underneath the back plate (A)
and remove it. Keep at least 6 inches (152.4mm) of cord. Use a pair of
wire-strippers to strip about a half inch of insulation for each wire on the cord.
10. Installation is complete.
5. Connect the hot wire from the fixture to the hot wire from the junction box (usually
11. Turn on the power at the junction box. Turn the light switch (F) clockwise to turn
on or turn off to test the fixture.
(D) LED Bulb (1)
(F) Switch (1)
black or smooth) with a wire connector (f) and wrap the connection with electrical
tape. Connect the neutral wire from the fixture to the neutral wire from the junction
box (usually white or ribbed) with a wire connector (f) and wrap the connection
with electrical tape. If your junction box has a ground wire (usually green or bare
copper), connect the ground wire from the fixture to it with a wire connector (f) and
wrap the connection with electrical tape. Otherwise, connect the ground wire from
the fixture to the green ground screw (e) on the mounting plate (c2).
This fixture has been rated for one 4-watt Type G9 LED dimmable lightbulb
(35-watt incandescent bulb equivalent). To avoid the risk of fire, do not exceed
the recommended wattage.
(c2) Mounting Plate (1)
(d) Back Plate Screws (2)
(e) Greeen Ground Screw (1)
HARDWARE ENCLOSED:
(f) Wire Connectors (3)
e
f
c2
g
4. Pass the wires of the junction box through the middle hole of the mounting
plate (c2). Attach the mounting plate (c2) to the junction box with the provided
mounting screws (g).
The side of the mounting plate (c2) marked “GND” must
face out.
6. After all wires are connected, tuck them carefully into the junction box. Place the
7. Insert back plate plug (h) into the cord hole underneath the back plate (A).
9. Place the shade (B) onto the socket.
Install the fixture in upright direction, do not install upside down to avoid the
glass shade to fall.
(g) Mounting Screws (2)
(h) Back Plate Plug (1)
A
B
D
C
d
F
hback plate (A) over the mounting plate (c2) and
align the two side holes of the back
plate (A) with the corresponding holes on the mounting plate (c2). Screw the back
plate screws (d) to tighten the back plate until the sconce is secured to the wall.
8. Insert the bulb (D) into the socket (C).
THIS PRODUCT IS NOT A TOY AND HASNO PLAY VALUE.
CONSULT A QUALIFIED ELECTRICIANTO ENSURECORRECT
BRANCH CIRCUIT CONDUCTOR.
