Rhino-Rack RBCA030 User manual

Page 1 of 3
RBCA030 Axle Adaptor including 15 x 100mm Insert.
Important: Please read these instructions carefully prior to installation.
Please refer to your fitting instruction to ensure that the Roof Rack System is installed in the
correct location.
Check the contents of kit before commencing fitment and report any discrepancies.
Place these instructions in the vehicle’s glove box after installation is complete.
1. Check Part No./Kit is correct 3. Fit roof rack accessory
2. Read through instruction before installing 4. Check and recheck all fasteners are secure
Maximum carrying capacity: 15kg/33lbs bicycle
Recommendations: For use with Rhino-Rack Road Warrior and Mountain Trail Bike Carriers and SQR.
It is essential that all bolt connections be checked after driving a short distance when you first install your bike rack. Bolt
connections should be checked again at regular intervals (probably once a week is enough, depending on road conditions, usage,
loads and distances travelled).
Bike Carrier is not suitable for Tandem bikes, E-bikes, recumbents.
Remove front fenders, child seats & panniers before use.
Warning: Locks are only a deterrent. Please exercise care when protecting your items from theft.
Sensitivity to cross winds, behaviour in curves and braking.
The handling characteristics of the vehicle, changes when you transport a load. For safety reasons, we recommend you exercise
extreme care when transporting wind-resisting loads; special consideration must be taken into account when braking.
Please remove bike rack when putting vehicle through an automatic car wash.
Load Ratings:
Maximum permissible load is 15kg/33lbs.
Note for Dealers and Fitters:
It is your responsibility to ensure instructions are given to the end user or client.
Rhino-Rack
3 Pike Street, Rydalmere, Document No: R906 Fit TIme: 10min
NSW 2116, Australia. Prepared By: Kayle Everett Issue No: 03
(Ph) [phone] Authorised By: Chris Murty Issue Date: 28/12/2016
(Fax) [phone]
These instructions remain the property of Rhino-Rack Australia Pty. Ltd. and may not be used or changed for any other purpose than intended.
Important Information
Note: For use with
Rhino-Rack Road Warrior
RBC036
Rhino-Rack Mountain Trail
RBC035
Rhino-Rack SQR RBC011
CONTROLLED

Page 2 of 3
RBCA030 Axle Adaptor including 15 x 100mm Insert.
Item Component Name Qty Part No.
1 ThruAxle Insert 15 x 100mm 1 CA1523
2 ThruAxleAdaptor 1 CA1522
3 M6 Grub Screws 2 B238
4 3mmAllen Key 1 H010
5 ThruAxle Insert 12 x 100mm 1 RBCA031
6 ThruAxle Insert 20 x 110mm 1 RBCA038
7 Instructions 1 R906
Item Additional Thru Axle Sizes (sold as separate). Part No.
1 ThruAxle Insert 9 x 135mm RBAC039
2 ThruAxle Insert 12 x 100mm RBCA031
3 ThruAxle Insert 15 x 150mm RBCA037
4 ThruAxle Insert 15 x 110mm RBCA036
5 ThruAxle Insert 20 x 110mm RBCA038
Instructions
1. 6.
2.
1Remove the front wheel from your bike. 2Slide the Thru Axle into the Adaptor. Be sure the
Thru Axle sits evenly in position as shown.
==
3Insert the Grub Screws provided. Tighten in place
with a 3mm Allen Key. Do not over-tighten. 4Fix the Adaptor to the bike by re-installing the bikes’s axle.
5Slide the two ends of the Quick Release Skewer (found in RCB035 and RCB036) into their respective
Carrier. Loosely install the skewer as per the bike carrier instructions.
1. Slide the two ends of the
Quick Release Skewer into the
assembly. Turn clockwise to
tighten.
2. Leave enough
space for the fork
of the bike (with
Adaptor installed)
to be seated onto
the Quick Release
Skewer.
Note: Be sure to identify correct size ThruAxle for
your bike. Additional sizes can be purchased to suit
most bikes. Installation requires 3mm Allen Key.
Bike Front Fork.
Bike Axle.
Thru Axle Adaptor.
4.
5.
3.

Page 3 of 3
RBCA030 Axle Adaptor including 15 x 100mm Insert.
6Place the bike onto the Carrier. The Thru Axle
Adaptor will sit onto the exposed sections of the
Quick Release Skewer as shown. Tighten and lock
in place (Skewer tightening detailed in RBC035/
RBC036).
7Secure the Bike Carrier before use.
Tighten the Carrier’s
Rear Wheel Strap.
Be sure to
tighten and lock
Skewer before
use.
Note For Mounting two or more bikes side by side,
alternate the orientation of the Adaptor when
installed. This will minimise the contact of
handlebars with the bike opposite.
Adaptors installed in
alternate orientation
when two or more
bikes are to be carried.
Note:
-Be sure fixtures are secure
before use.
-Periodically check torque on
fixtures.
Front View: The
Adaptor must sit
flush with the top
of the Carrier as
shown.