RHINO Auta-lite I Series User manual


 
 


Series I
Document: Auta-Lite.doc
Release: 2 October 2003
I n s t r u c t i o n s
Designed and Manufactured in Australia by












International Patent: PCT/AU02/00705
www.rhino.com.au

2
Introduction :
The Auta-lite

Emergency Override Light Switch
is a unique device that simply replaces the standard light switch in a room. In everyday use, the end user
operates the light switch as per normal i.e they manually switch the lights on and off. However, the lights can
automatically be turned on at any time by a range of compatible wireless radio transmitters including
movement sensors, smoke sensors, door & window sensors, remote controls, or even wireless impact sensors.
A tiny retro-fit transmitter is also available for use with existing alarm detectors, or for connecting to the
output of an alarm control panel. The emergency override function may be used for emergency or remote
controlled lighting or for use when an alarm system activates to automatically turn on room lights to scare off
intruders. A primary application is also for use with CCTV installations, where most cameras can not see at
night due to insufficient lighting. The Auta-lite allows new or existing alarm detectors to not only trigger the
alarm system, but to also automatically switch on the room lights enabling the cameras to see and record.
For use in Australia, we chosen a quality HPM brand wall switch to integrate with our state-of-the-art
electronic Auta-litereceiver circuitry, giving a perfect combination for our application.
Front Cover On Front Cover Removed
Wireless PIR
Movement Detector
Note: The device used
however can be any one of the
following:
• An existing hardwired alarm sensor or
alarm control panel fitted with our retro-
fit ENSA Transmitter
• A detector made by an electronic
security manufacturer who has
incorporated an ENSA transmitter as
part of their design
• A Wireless PIR, Wireless Reed Switch,
Wireless Smoke Sensor, Wireless
Impact Sensor or Wireless Remote
Control made by RhinoCo
Quick Installation Overview
Simply remove your existing light switch and replace with an Auta-liteEmergency Override Light Switch.
In most Australian homes, you won’t even have to drill any new holes, as the template for the existing wall
switch will be identical to the Auta-lite. Now install a suitable wireless detector and learn it in to the
Auta-lite. Now adjust the light on time & light level to suit your room. In fact, the whole installation process
should take a licensed electrician less than 10 minutes!
Quick Operation Overview
To turn the lights on & keep them on
permanently:
Flick the switch to the on position.
To turn off the lights or to enable automatic
activation of lights:
Flick the switch into the off position.
Specifications:
Load: Must consist of a Resistive Element. EG:
Fluorescent, Energy Saving Lights,
Incandescent Light or Fan. Not suitable for
Induction motor or inductor loads.
Load Limit: 400 Watts maximum
Power Supply: 240 Volts @ 50Hz
Note: Fluorescent lights may have
ballast of similar ratings
(approximately ±20Watts) to the light
itself i.e. a 35W fluorescent light may
have a 35W ballast, therefore the load
for that one fluorescent tube would be
35W + 35W = 70Watt.

3
Installation
The Auta-lite is installed easily using the existing wires from your old light switch.
THIS MUST BE CARRIED OUT BY A LICENCED ELECTRICIAN.
Standard Load Wiring Diagram Fluorescent Lamp Wiring Diagram
On certain fluorescent light installations a
power factor correction capacitor may need
to be installed. If so refer to the diagram
above.
IMPORTANT NOTE:
NEVER MOUNT LIGHT BLUBS WITH THE FILAMENT FACE UP (see picture
right). The filament will fall and short across the bulb terminals if
and when the light globe blows. This will in-turn cause a component
(the triac) on the ENSA to heat up and destroy itself. This is not
covered under warranty.

4
Adding A Wireless Device
A wireless device may be any product with the “ENSA Equipped”
label (shown left) displayed on the product itself, its instructions or
its packaging. ENSA Equipped products are available from where
you bought your Auta-Lite Emergency Override Light Switch.
    
Make sure the
switch is in
Auta-lite
mode.
    
Remove the
front cover by
pulling the
front face
plate out from
the top edge.
    
Turn the timer
setting to its
most anti-
clockwise
position with
the tool
provided.
    
Turn the light
sensitivity
setting to its
most clockwise
position with
the tool
provided.
    
Press the
yellow “Learn
Detector”
button using
the plastic end
of the
screwdriver
tool provided.
    
Immediately
after pushing
the yellow
button trigger
the wireless
device.


 
 
See separate
manual supplied
with each device
on how to trigger.
    
Test that each
time the
device is
triggered that
the light turns
on for 3
seconds
(approx).

If this doesn’t
work go back to
step 6
    
Turn the light
sensitivity
setting and the
timer setting to
the desired
level and
replace the
front face plate.

5
Adjusting the light sensor
This adjustment will set the level of light at which the Auta-lite will stop turning the
light(s) on. Generally, the lights should not turn on when the natural light in the room
is sufficient.
To adjust the light sensor you must remove the front face plate of the Auta-lite. Use
the supplied tool to make the adjustment.
Turn the adjustment in the clockwise direction if the Auta-lite:
• is turning on unnecessarily because there is already sufficient natural
lighting in the room.
That is, you don’t want the lights to turn on until the room is darker.
Turn the adjustment in the anti-clockwise direction if the Auta-lite:
• is not turning on the light when there is insufficient natural lighting in
the room.
That is, the room is dark and the lights aren’t turning on.
Adjusting the timer
This adjustment will set the duration the light will stay on
for after the wireless device has triggered. This time will
reset each time the wireless device(s) is triggered. Set this
to suit your own desired requirements or specific
application.
Turn the adjustment in the clockwise direction to increase the amount
of time the light stays on for after being triggered.
If the adjustment is at its most clockwise position the setting will be
maximum. The maximum time is approximately 1 hour.
Turn the adjustment in the anti-clockwise direction to decrease the
amount of time the light stays on for after being triggered.
If the adjustment is at its most anti-clockwise position the setting will be 3
seconds. If the adjustment is turned clockwise just a slight amount the
minimum time will be 4 minutes.

6
Operation
The Auta-lite works in the same manner as a traditional lightswitch, with the exception
that when it is tuned off, a programmed “ENSA Equipped” wireless device can
override the switch and turn the lights on, when the “ENSA Equipped” wireless device
is triggered.
ON MODE
If at any time you would like to turn the light on without needing
the wireless device to trigger, you may press the switch to the down
position to turn the light on just like you would on a regular light
switch.
AUTA-LITE MODE

When the switch is off, the lights will turn on when a programmed
“ENSA Equipped” wireless device is triggered and there is
insufficient natural light. The light will stay on for a predetermined
amount of time.

7
Warranty Terms & Conditions
The expression “The Company”, when referred to in these Terms and Conditions, refers to
CORNICK PTY LTD ABN 74 001 621 610 (T/as RhinoCo Technology).
The Company warrants its products to be in conformance with its own plans and specifications and to be free
from defects in materials and workmanship under normal use and service for 12 (twelve) months from the
date of original purchase.
The Company’s obligation shall be limited to repairing or replacing, at its option, free of charge for materials or
labor, any part which is proved not in compliance with The Company’s specifications or proves defective in
materials or workmanship under normal use and service. The Company shall have no obligation under this
Limited Warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than
The Company.
For warranty service, return the product (transportation prepaid) to:
RhinoCo Technology, 9 Hannabus Place, McGraths Hill, NSW 2756 Australia
There are no warranties, expressed or implied, of merchant ability, or fitness for a particular purpose or
otherwise, which extend beyond the description on the face hereof. In no case shall The Company be liable to
anyone for any consequential or incidental damages for breach of this or any other warranty, express or
implied, or upon any other basis of liability whatsoever, even if the loss or damage is caused by its own
negligence or fault. The Company's maximum liability shall not in any case exceed the purchase price of the
product, which shall be the complete and exclusive remedy against The Company.

A u t a - L i t e 

W i r e l e ss L i g ht S w i t c h W a r r a n t y C a r d
Please return this card inside a stamped envelope to the address shown on the reverse.
Name
Address
Suburb State Postcode
Email
Date of Purchase Invoice Number
Daytime Phone
Where did you purchase your Auta-Lite?
Store Location
Auta-Lite installed by:
Do You Have Any Comments / Suggestions Regarding This Product:
This information will only be used by the manufacturer and will not be not be sold to any third parties.

8
Troubleshooting
Symptom Solution
Light won’t turn on at
all
• Check your wiring
• Ensure that the load is not over the 400-Watt limit.
• The Auta-Lite is unserviceable, return it to your
supplier for repair by the manufacturer.
The light only turns on
for 3 seconds
• Turn the timer adjustment clockwise
• See adjusting the timer section of this manual
The light stays on and
will not turn off
• Press the right switch to the up position (OFF).
• Turn the timer adjustment anti-clockwise
• See adjusting the timer section of this manual
The light doesn’t turn on
after the wireless device
triggers
• Turn the light adjustment anti-clockwise
• Program the wireless device into the Auta-lite (see
adding a wireless device section in this manual)
The light pulses on and
off intermittently
• The lightswitch has automatic protection to stop the
lightswitch from overheating caused by
overloading. The load is greater than 400W.

RhinoCo Technology
9 Hannabus Place
McGraths Hill NSW 2756
AUSTRALIA