RIAREX RBR-SB-KTZ001 User manual

RBR-SB-KTZ001
LAR 2
User Manual

INTRODUCTION
KTZ001 is a compact, waterproof stand-alone programmable access control system that provides
proximity entry for up to 2000 users. Read both EM and HID card. It uses Atmel microcontroller that
assures maximum performance in any environment, and the low-power circuit makes its service life
prolonged.
The product unique feature is simple in design, easy to operation and high reliability.
Features:



Waterproof, conform to IP66



125 kHz EM&HID card



One programmable relay operation



Pulse mode, Latch mode



Remote infrared programmer



2000 users



Card block enrolment



Tri-colour LED status display



Built in light dependet resistor LDR for anti tamper



Buzzer for audible or silent mode



Low Temperature Resistance (-40°C)
Specifications:
User Capacity 2000
EM card HID card
Operating Voltage
Idle Current
12~24 VDC
＜40mA
Proximity Card Reader
Radio tecnology
Read Range
EM&HID
125 kHz Proximity Card
3-10cm
Wiring Connections Relay Output, Exit Button
Relay
Adjustable Relay output Time
Lock Output Load
1 x (C, NO, NC)
1-99 sec (5 sec default)
2 A Max
Environment
Operating Temperature
Operating Humidity
Meets IP66
-40℃ ~60℃
20%RH-98%RH
Physical
Color
Dimensions
Unit Weight
Shipping Weight
ABS Shell
Black
H: 102* Sz: 48 * M:20mm
150g
250g
Card

Carton Inventory:
1 x RBR-SB-KTZ Reader
1 x Infrared Remote Control
1 x Diode IN4004 (for relay circuit protection)
2 x Self tapping Screws：Φ3*25mm
2 x Wall Anchors
1 x Screw Driver
INSTALLATION



Remove the back cover from the unit



Drill 2 holes (A, C) on the wall for the screws and one hole for the cable.



Fix the back coverfirmly on the wall with 2 flat head screws.



Attach the unit to the back cover.
Knock the supplied rubber bungs to the screv holes (A, C) .



Thread the cable through the cable hole ( B ).




Wiring
Colour Function Notes
Red Power + 12~24 V DC Regulated Power Input
Black GND Ground
White
NO
Normaly Open relay
Brown
COM
Common for relay output
Green
NC
Normaly Closed relay
Yellow
OPEN Request to exit Input (REX)
Connection Diagram
Common power suplly:
Attention: Install a 1N4004 or equivalent diode is needed when use a common power suplly, or the
reader might be damaged. ( 1N4004 is included in the packing).
Access Control Power Suplly:

PROGRAMMING
Programming will vary depending on access configuration. Follow the instructions according to your
access configuration.
General Programming Information

Remote Control: Please use the Infrared Remote Control to program the Reader. The infrared
receiver head is near LED, so when program the reader, direct the Remote Control to the LED.
User ID number: Assign a user ID to the access card in order to track it. The user ID number can
be any number from 1~2000. IMPORTANT: User IDs do not have to be proceeded with any leading
zeros. Recording of User ID is crical. Modifications to the user require the User ID be available.
Proximity Card: Any 125KHz industry standard 26 bit EM and HID Proximity card or Tag.
Enter and Exit Program mode
Set Master Code
Programming Step Keystroke Combination
1. Enter Program Mode ﹡
﹡﹡
﹡(Master Code) #
2. Update Master Code 0（New Master Code）#（Repeat New
Master Code）#
3. Exit Program Mode *
Add User Cards
Programming Step Keystroke Combination
1. Enter Program Mode ﹡
﹡﹡
﹡(Master Code) #
2. Add Card: Using Auto ID
(Allows KTZ001 to assign Card to next
available User ID number)
OR
2. Add Card: Select Specific ID
(Allows manager to define a specific User
ID to associate the card to)
OR
2. Add Card: by Card Number
1 (Read Card) #
Repeat Step 2 for additional user cards
1 (User ID) # (Read Card) #
The user ID is any number from 1-2000.
1 (Input 8/10 digits Card number) #
Programming Step Keystroke Combination
Enter Program Mode ﹡
﹡﹡
﹡(Master Code) #
Factory default is 123456
Exit Program Mode *

OR
2. Add Card: Block Learn
(Allows manager to add up to 2000 cards
to the Reader in a single step.) Takes 3
minutes to program.
1 ( User ID number) # (Card quantity)
#(The first card number) #
Cards’ number must be consecutive;
Card quantity = number of card to be enrolled.
3. Exit ﹡
﹡﹡
﹡
Delete User Cards
Programming Step Keystroke Combination
1. Enter Program Mode ﹡
﹡﹡
﹡(Master Code) #
2. Delete Card: By read card
OR
2. Delete Card: Select Specific ID
OR
2. Delete Card: by Card Number
2 (Read Card) #
Repeat Step 2 for additional user cards
2 (User ID) #
The user ID is any number from 1-2000.
2 (Input 8/10 digits Card number) #
Set Relay Configuration
The relay configuration sets the behaviour of the output relay on activation.
Programming Step Keystroke Combination
1. Enter Program Mode ﹡
﹡﹡
﹡(Master Code) #
2. Pulse Mode
OR
2. Latch Mode
3 (1-99) # The relay time is 1-99
seconds(default is 5 seconds)
3 0 #
Sets the relay to ON/OFF Latch mode
3. Exit
﹡
﹡﹡
﹡
Set Strike-out Alarm
The strike-our alarm will engage after 10 failed card attempts. Factory is OFF. The strike-our alarm ca
be set to deny access for 30 minutes after engaging or it can be set disengage only after entering a valid
card or Master code.
Programming Step Keystroke Combination
1. Enter Program Mode ﹡
﹡﹡
﹡(Master Code) #
2. Strike-Out OFF
OR
2. Strike-Out ON
OR
2. Strike-Out ON (Alarm)
Set alarm time
4 0 # (factory default)
4 1 # Access will be denied for 10 minutes
4 2 #
5 (0 ~ 30) #, factory default is 1 minute
Enter Master code # or valid user card to
silence
3. Exit
﹡
﹡﹡
﹡

1. Enter Program Mode ﹡
﹡﹡
﹡ (Master Code) #
2. Control LED
OR
2. Control Sounds
OFF = 6 1 #
OFF = 6 3 #
ON = 6 2 #
ON = 6 4 #
(Factory defaults are ON)
3. Exit
﹡
﹡﹡
﹡
Others
Users Operation:
Open the door: Read the valiad user card, the door will open.
Remove Alarm: Read valid user card, or Input Master code #
Reset to Factory Default:
To reset to factory default, power off, press Exit door button , hold it and power on, release it after
hear two beeps, the LED light will turn into yellow, after 10 seconds, it will turn into red after one beep,
mean reset to factory default successfully.
Remarks: Reset to factory default, the user’s information is still retained.
Erase all Cards
This will delete ALL User data.
1, Enter Program Mode by press: *(Master Code) #.
2, Press 2 and Master code again
3, Exit: *
All configuration data is retained.
S
ound and Light indication
Operation Status LED Buzzer
Stand by Red light bright -
Enter into programming mode Red light shines ne beep
In the programming mode Yellow light bright ne beep
peration error - Three beeps
Exit from the programming mode Red light bright ne beep
pen lock Green light bright ne beep
Alarm Red light Shines quickly Beeps
Set Audible and Visual Response
Programming Step Keystroke Combination

change the master code 0 – new code - # - repeat the new code - #
(code: 6 digits)
Add card user 1- Read Card - #
(can add Cards continuously)
Delete card user – Read Card -#
(can delete Cards continuously)
Exit from the programming mode *
How do release the door
Card User Read card
KTZ001- Simplified Instruction
Function description Choose from the relevant functions below and input
Enter the programming mode *- 1 3456 - #
then you can do the programming
(123456 is the default factory master code)