RIAREX EVD-L04/100A1-960 User guide

EVD-L04/100A1-960, EVD-L08/200A1-960 and
EVD-L16/400A1-960 DVRs
Quick Operation Guide

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
1
T ank you for purc asing our product. If t ere is any question or request, please do not esitate to contact dealer.
T is manual is applicable to
EVD-L04/100A1-960, EVD-L08/200A1-960, EVD-L16/400A1-960
DVR Pre-Installation
T e DVR is ig ly advanced surveillance equipment t at s ould be installed wit care. Please take into
consideration t e following precautionary steps before installation of t e DVR.
1. Keep all liquids away from t e DVR.
2. Install t e DVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD.
DVR Installation
During t e installation of t e DVR:
1. Use brackets for rack mounting.
2. Ensure t ere is ample room for audio and video cables.
3. W en installing cables, ensure t at t e bend radius of t e cables are no less t an five times t an its diameter.
4. Allow at least 2cm (≈0.75-inc ) of space between racks mounted devices.
. Ensure t e DVR is grounded.
6. Environmental temperature s ould be wit in t e range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.
7. Environmental umidity s ould be wit in t e range of 10% ~ 90%.
Hard Disk Installation
Before you start:
Before installing a ard disk drive (HDD), please make sure t e power is disconnected from t e DVR. A factory
recommended HDD s ould be used for t is installation.
Tools Required: Screwdriver.
T e following section as described t e HDD installation of DS-7100HVI/HWI-SL DVR as t e example.
To install a HDD on your DVR:
1. Remove t e cover from t e DVR by unfastening t e screws on t e back and side.
2. Install t e HDD in t e HDD rack using t e provided screws. Fasten t e screws on t e bottom to fix t e HDD.
3. Connect t e HDD to t e mot erboard of t e DVR wit t e included data cable, and connect t e power cable to
t e HDD.

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
2
4. Re-install t e cover of t e DVR and fasten screws.
Front Panel
EVD-04/100A1-960, EVD-L08/200A1-960, EVD-L16/400A1-960
Table 1 Description of Indicators
No. Icon Description
1 Indicator turns red w en DVR is powered up.
2 Indicator lig ts in red w en data is being read from or written to HDD.
3 Indicator blinks blue w en network connection is functioning properly.

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
3
Rear Panel
EVD-L04/100A1-960, EVD-L08/200A1-960, EVD-L16/400A1-960
T e rear panel of EVD-L08/200A1-960 is s own below:
 T e EVD-Lxx/xxxA1-960 series DVR provides no HDMI interface.
 T e EVD-L04/100A1-960 provides 4 video input interfaces and t e EVD-L16/400A1-960 provides 16
video input interfaces on t e rear panel.
Table 2 Description of Rear Panel
No. Item Description
1 VIDEO IN BNC connector for analog video input.
2 VIDEO OUT BNC connector for video output.
3
HDMI
HDMI video output.
T e EVD-Lxx/xxxA1-960series DVR provides no HDMI interface.
4 VGA DB15 connector for VGA output. Display local video output and menu.
AUDIO IN RCA connector for audio input.
6 AUDIO OUT RCA connector for audio output.
7 LAN Interface RJ45 10M / 100M Et ernet interface.
8 USB Interface Connects USB mouse or USB flas memory devices.
9 12V 12VDC power supply.
10 GND Ground (needs to be connected w en DVR starts up)

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
4
Specifications
Table 3 Specifications for EVD-Lxx/xxxA1- 60 series
T e EVD-Lxx/xxxA1-960 series DVR provides no HDMI interface.
Model
EVD-L04/100A1-960 EVD-L08/200A1-960 EVD-16/400A1-960
Video/Audio
input
Video compression H.264
Video input 4-c 8-c 16-c
Video input interface BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive
Audio compression G.711u
Audio input 1-c , RCA (2.0 Vp-p, 1 kΩ)
Two-way audio input 1-c , RCA (2.0 Vp-p, 1 kΩ) (using t e audio input)
Video/Audio
output
HDMI/VGA output
1-c , resolution:
1080P: 1920×1080/60Hz, SXGA: 1280×1024/60Hz,
720P: 1280×720/60Hz, XGA: 1024×768/60Hz
CVBS output 1-c , BNC (1.0 Vp-p, 75 Ω),
resolution: PAL: 704 × 576, NTSC: 704 × 480
Encoding resolution WD1/4CIF/2CIF/CIF/QCIF
Frame rate 25 fps (P) / 30 fps (N)
Video bitrate 32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)
Audio output 1-c , RCA (Linear, 1 kΩ)
Audio bitrate 64 Kbps
Dual-stream Support;
Sub-stream: CIF/QCIF @ 25 fps (P) / 30 fps (N)
Stream type Video, Video & Audio
Synchronous playback 4-c 8-c 16-c
Hard disk SATA 1 SATA interface
Capacity Up to 4TB capacity
External
interface
Network interface 1, RJ45 10M / 100M Et ernet interface
USB interface 2, USB 2.0
General
Power supply 12 VDC
Consumption
(without hard disk or
DVD-R/W)
≤ 6 W ≤ 8 W ≤ 10 W
Working temperature -10 ºC ~+55 ºC
Working humidity 10% ~ 90%
Dimensions
(W × D × H) 200 × 200 × 45 mm 200 × 200 × 45 mm 285 × 210 × 45 mm
Weight
(without hard disk or
DVD-R/W)
≤ 0.8 kg ≤ 1 kg ≤ 1.5 kg

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
5
HDD Storage Calculation Chart
T e following c art s ows an estimation of storage space used based on recording at one c annel for an our at a
fixed bit rate.
Bit Rate Storage Used
96Kbps 42M
128Kbps 56M
160Kbps 70M
192Kbps 84M
224Kbps 98M
256Kbps 112M
320Kbps 140M
384Kbps 168M
448Kbps 196M
512Kbps 225M
640Kbps 281M
768Kbps 337M
896Kbps 393M
1024Kbps 450M
1280Kbps 562M
1536Kbps 675M
1792Kbps 787M
2048Kbps 900M
3072Kbps 1350M
Please note t at supplied values for storage space used is just for reference. Storage space used is estimated
by formulas and may ave some deviation from actual value.

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
6
Menu Operation
Menu Structure
T e menu structure is s own as below:
T e EVD-Lxx/xxxA1-960 series DVR provides no PTZ feature.
Startup and Shutdown
Proper startup and s utdown procedures are crucial to expanding t e life of t e DVR.
Before you start:
C eck t at t e voltage of t e extra power supply is t e same wit t e device’s requirement, and t e ground
connection is working properly.
Starting up the device:
Steps:
C eck t e power supply is plugged into an electrical outlet. It is HIGHLY recommended t at an Uninterruptible
Power Supply (UPS) be used in conjunction wit t e device.
For t e EVD-Lxx/xxxA1-960 series DVR, insert t e power supply plug into t e power connector on t e rear panel
and t e device will start up. T e Power indicator LED s ould turn red indicating t at t e device begins to start up.
Shutting down the device:
Steps:
1. Enter t e S utdown menu.
Menu > S utdown
2.

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
7
3. Click t e Shutdown button.
4. Click t e Yes button.
. Disconnect t e power supply of t e device.
Using the Setup Wizard
T e Setup Wizard can walk you t roug some important settings of t e device. By default, t e Setup Wizard starts
once t e device as loaded.
Operating t e Setup Wizard:
1. Select t e system resolution from t e dropdown menu. T e default resolution is 1280×1024/60Hz.
Click Apply to save t e resolution settings.
2. C eck t e c eckbox to enable Setup Wizard w en device starts. Click Next to continue t e setup wizard.
Follow t e guide of t e Setup Wizard to configure t e system resolution, password modification, system
date/time, network settings, HDD management, record settings, etc.
Live View
Some icons are provided on screen in Live View mode to indicate different camera status. T ese icons include:
Live View Icons
In t e live view mode, t ere are icons at t e rig t top of t e screen for eac c annel, s owing t e status of t e
record and alarm in t e c annel, so t at you can find problems as soon as possible.
Alarm (video loss, tampering or motion detection alarm).
Record (manual record, sc edule record or motion detection record)
Alarm & Record
Using the Mouse in Live View
In t e live view mode, use t e mouse to rig t-click on t e window to access t e following menu:

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
8
Table 4 Mouse Operation in Live View
Name Description
Menu Enter t e main menu of t e system by rig t-clicking t e mouse.
Single Screen Switc to t e single full screen by c oosing c annel number from t e dropdown list.
Multi-screen Adjust t e screen layout by c oosing from t e dropdown list.
Previous Screen Switc to t e previous screen.
Next Screen Switc to t e next screen.
Start/Stop
Auto-switc
Enable/disable t e auto-switc of t e screens.
T e dwell time of t e live view configuration must be set before using Start
Auto-switch.
Start Recording Start all-day normal recording or motion detection recording for all c annels.
Quick Set Set t e video output mode to Standard, Brig t, Gentle or Vivid.
All-day Playback Play back t e video of t e selected c annel.
Aux Monitor Switc to t e auxiliary output mode and t e operation for t e main output is disabled.
If you enter Aux monitor mode and t e Aux monitor is not connected, t e mouse
operation is disabled.
Main/Aux Output Switching
W en t e VGA output is configured as t e main output, you can perform t e following operation to switc to
CVBS output as t e main output.
Steps:
1. In t e live view mode, use t e mouse w eel to double-click on t e VGA output screen, and t e following
message box pops up:
2. Use t e mouse w eel to double-click on t e screen again to switc to t e Aux output, or click Cancel to

Quick Operation Guide of EVD-Lxx-xxxA1-960 seriesDVR
9
cancel t e operation.
3. Select t e Menu Output Mode to Main CVBS from t e rig t-click menu on t e CVBS output screen.
4. On t e pop-up message box, click Yes to restart t e device to enable t e CVBS output as t e main output.
You can select t e Menu Output Mode under Menu > Configuration > More Settings to Auto or VGA and
t en restart t e device to switc t e main output back to VGA output.
Record
You can use t e rig t-click menu in live view mode to configure recording for all c annels.
1. In t e live view mode, use t e mouse to rig t-click on t e window to access t e following menu:
2. Click t e Start Recording submenu and select t e recording mode to Normal Record or Motion Detection
Record.
3. In t e pop-up message box, click Yes to finis t e quick recording settings for all c annels.
T e full-screen motion detection triggered recording is configured by default in t is mode.
Playback
Play back t e record files of a specific c annel in t e live view menu.
Instant playback by channel
C oose a c annel under live view using t e mouse and click t e button in t e s ortcut operation menu.
Only record files recorded during t e past five minutes on t is c annel will be played back.