Riccar Hybrid Central Vac User manual

Installation
Operating
Instructions
MaintenanceTroubleshooting
Warranty
Information
OWNER’S MANUAL
DOMESTIC USE ONLY
Please read this document carefully before installing and/or using
your vacuum cleaning system.
Model : _______________ Serial Number : ________________________

2
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should always be followed,
including the following.
Read all instructions before using this appliance
WARNING – To reduce the risk of fire, electric shock, or injury:
1. Do not leave appliance when plugged in. Unplug from outlet when not in use
and before servicing.
2. Do not use outdoors or on wet surfaces.
3. Do not allow to be used as a toy. Close attention is necessary when used
by or near children or infirm persons. This appliance is not intended for
use by people (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning the use of the appliance by a
person responsible for their safety.
4. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug. If appliance is not working as it should,
has been dropped, damaged, left outdoors, or dropped into water, return it to
a service center.
6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or
pull cord around sharp edges or corners. Do not run appliance over cord. Keep
cord away from heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9. Do not put any objects into openings. Do not use with any opening blocked;
keep free of dust, lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings
and moving parts.
11. Do not pick up anything that is burning or smoking, such as cigarettes,
matches, or hot ashes.
12. Do not use without dust bag and/or filters in place.
13. Turn off all controls before unplugging.
14. Use extra care when cleaning on stairs.
15. Do not use to pick up flammable or combustible liquids such as gasoline or
use in areas where they may be present.
16. Connect to a properly grounded outlet only. See Grounding Instructions.
SAVE THESE INSTRUCTIONS

3
Table of Contents
Preface............................................................................................4
Schematic .......................................................................................4
Installation
Unit Installation ................................................................................5
Using the right air intake ..................................................................6
Utility Valve Installation .....................................................................7
Dos & Don’ts ...................................................................................8
Mufer Installation..........................................................................11
Electric Connections......................................................................11
Grounding Instructions ..................................................................12
Low Voltage Connections ..............................................................13
Operating instructions
Hose Hook-up & Inlets...................................................................14
Progressive Start ...........................................................................15
Automatic Stop .............................................................................15
LED indicator.................................................................................15
Information center .........................................................................15
Maintenance
Motor ............................................................................................16
Use with bag .................................................................................17
Use without bag ............................................................................18
Converting the unit ........................................................................19
Carbon Dust Filter..........................................................................20
Troublehooting
General Information .......................................................................21
Decrease in suction strength..........................................................22
Vacuum will not start......................................................................24
Vacuum will not stop......................................................................25
Warranty Information
Limited Lifetime Warranty...............................................................26

4
6
min. 30 cm (12")
min. 30 cm (12")
Recommended 40 cm (16")
min. 30 cm (12")
min. 30 cm (12")
7
min. 30 cm (12")
If the muffler is turned down
Preface
Your new Riccar central vacuum system was designed and manufactured
in Blainville, Quebec, by the largest central vacuum cleaner manufacturer
in Canada, providing a high-quality, state-of-the-art product. Our exten-
sive network of qualified professionals ensures first quality service near
you. Contact us for the location of the Riccar authorized service center in
your area.
Schematic
1. Circuit Breaker
2. Information center (H60 & H110 only)
3. Low Voltage Connectors
4. Serial Number
5a.Left air intake
5b.Right air intake
(except H10)
Seal the unused air intake
with the provided cap.
6. Carbon Dust Filter
(H60 & H110 (2x) only)
7. Muffler
(2 mufflers on H110)
5a 5b
4
2
1
3
C
I
R
C
U
I
T
B
R
E
A
K
E
R
P
r
e
s
s
t
o
r
e
s
e
t
#SÉRIE - SERIAL#
FF00000000
4
1
3

gure 1
gure 2
gure 3
5
Installation
Unit Installation
Using the mounting plate provided with
your vacuum cleaner, secure the unit to
the wall (figure 1), at a height allowing
easy access for maintenance of the dirt
receptacle and/or bags (see page 4).
The connections to the piping system
will require some basic tools: a mitre
box and small saw or a pipe cutter
(figure 2). See pages 8 and 9 for general
instructions pertaining to the preparation
of PVC pipes. To simplify matters,
installation kits, including necessary
fittings, pipes, glue and wiring, as well
as a detailed instructions booklet, are
available from Riccar service centers.
Contrary to all other connections in the
piping system, do not glue the last fitting
to your unit. Use te provided rubber
seal and clamp collars to secure the
last fitting to the air intake and obtain an
air-tight fit (figure 3).

6
Installation
Using the Right Air Intake
(except H10 model)
To use the air intake located on the right side
of the vacuum:
1. Using a flat screwdriver, loosen the clamp
collars and remove the rubber coupling
from the left air intake (figure 4).
2. Unlatch the two clips and remove the dust
receptacle (see page 17, figure 15).
3. Remove the bag if needed for more
convenience (see page 17).
4. Pull the bag adaptor out of the left air intake
(figure 5).
5. Remove the cap on the right air intake
(figure 6) and put it on the left air intake.
Making sure that the tabs are aligned with
the notches, push the cap completely in
(figure7).
6. From the inside of the vacuum, insert
the bag adaptor into the right air intake,
making sure that the embossed lines on the
adaptor are aligned with the slots in the air
intake (figure8). Outside the vacuum, the
end of the adaptor should come out of the
air intake about ¾" (1.9 cm).
7. Put the rubber coupling on the right air
intake and tighten the clamp collars using a
flat screwdriver.
8. Put the bag and dust receptacle back in
place and latch botch clips (see page 17).
gure 5
gure 4
gure 7
gure 8
gure 6

7
Installation
Utility Valve installation
(H40, H60 & H110 models)
1. Secure the T-elbow on the air intake (see page 5, figure 3).
2. Install the utility valve on the T-elbow.
3. Connect the low voltage wiring (see pages 10 & 13).

8
Installation
Dos & Don’ts
Installing Conduits

9
Installation
Dos & Don’ts
Installing Conduits

A
B
A
B
B
B
A
A
10
Installation
Dos & Don’ts
Installing Inlets
When installing your vacuum inlets, we recommend that the principle of
electric polarity be taken into account. Ensure that the wire connected
onto contact A on inlet 1 is the same as that connected to contact A on
inlet 2, and so on. Do not cross, reverse or interchange wires.
Inlet 1
Inlet 1
Inlet 2
Inlet 2

11
Installation
Mufer Installation (Optional)
1. Insert the rubber coupling on the vacuum air exhausts.
2. Using a Phillips screwdriver, tighten the clamp collar to ensure ad-
equate sealing.
3. Insert the 90° elbow into the rubber coupling, and tighten then clamp
collar as per instructions in step 2.
4. Apply ABS glue to the 90° elbow and insert muffler.
5. For H110, repeat steps 1 to 4 to install second muffler turned down.
Electric Connections
There should be an electric outlet within 1 meter (3 feet) of your central
vacuum unit. Once the appliance is installed in a suitable location, con-
nect your central unit to an electric outlet on an dedicated* grounded
circuit. Do not use extension cords or modify the length of your vacuum
cleaner’s power cord.
Dedicated* grounded circuit
• NorthAmerica
120 V / 240 V All models: 15A
Your central vacuum cleaner has a thermal safety device or a circuit break-
er to protect against any over voltage or electrical defect. If that protection
should fail, contact your authorized service center.
*Please reserve a circuit breaker dedicated only to the connections for your
central vacuum.
If you nd that installing your vacuum cleaner is too difcult, ask your service
center to install it for you. When in doubt, it is better to have the work done by a
professional and ensure that the unit is properly installed. Any installation that
does not comply with the specied norms could alter or invalidate the warranty.
B
C
D
A
AA. Rubber coupling
B. 90° elbow
C. Muffler
D. Air Exhaust
Glue not included

12
Installation
Grounding Instructions
This appliance must be grounded. If it should malfunction or breakdown,
grounding provides a path of least resistance for electric current to
reduce the risk of electric shock. This appliance is equipped with a cord
having an equipment-grounding conductor and grounding plug. The plug
must be inserted into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances. No adaptor
should be used with this appliance.
WARNING
Improper connection of the equipment-grounding conductor can result in
a risk of electric shock. Check with a qualified electrician or service person
if you are in doubt as to whether the outlet is properly grounded. Do not
modify the plug provided with the appliance – if it will not fit the outlet; have
a proper outlet installed by a qualified electrician.
120V Models
This appliance is for use on a nominal 120 V circuit,
and has a grounded plug (figure 9). Make sure that
the appliance is connected to an outlet having the
same configuration as the plug. No adaptor should
be used with this appliance.
220V/240V Models
(H110 only)
This appliance is for use on a circuit having a nominal
rating more than 120 V and is factory-equipped with
a specific cord and plug to permit connection to a
proper electric circuit. Make sure that the appliance is
connected to an outlet having the same configuration as
the plug. No adaptor should be used with this appliance.
If the appliance must be reconnected for use on a
different type of electric circuit, the reconnections should
be made by a qualified service personnel.
gure 9

13
Installation
Low Voltage Connections
Connect the low voltage wires to the low voltage inlet on your unit.
To do so:
1. Strip wires over 1 cm (1/2 inch) (figure 10).
2. Gently press on the toggle to open the connector (figure 11).
3. Insert stripped wire (figure 12).
4. Release toggle to secure wire in connector (figure 13).
5. Repeat for second wire.
To disconnect:
1. Gently press on the toggle to open the connector.
2. Remove low voltage wire from connector.
gure 11gure 10
gure 12 gure 13
LED
Except H60 &
H110 models
details on
page 15

gure 14
14
Operating Instructions
Hose Hook-up & Inlets
Before operating your central vacuum…
Please verify that it is properly connected to the piping system, and to a
grounded electrical outlet, and that the low voltage wires are connected to
the unit (see pages 5 to 13). Then read the complete owner’s manual and
proceed with a quick verification of your unit’s installation:
• Checkfilterandbagtobesuretheyareproperlyinstalled.
• Checkrubbersealsineachvacuuminlet.
• Plugthehosealternativelyintoeachvacuuminlet,toensurethateach
one works properly.
• Whilethehoseisstillpluggedintooneinletandthesystemisopera-
tional, check other inlets for leaks.
To start your central vacuum, simply insert the hose in the vacuum inlet of
your choice. Please ensure that the tab on the hose end is properly lined
up with the slot in the inlet opening (figure 14). If your hose handle has an
integrated on/off switch, simply slide the switch to the “on” position.
Do not try to open another inlet while your system is in
operation, as it may damage the inlet’s rubber seal.

15
Operating Instructions
Progressive start
(H60 & H110)
Each model is equipped with a special module allowing for a smooth and
gradual start-up of the vacuum system, to prolong motor durability.
Automatic stop
(H60 & H110)
In case you’ve forgotten to turn off your vacuum, or it’s been turned on by
mistake, your vacuum system wil automatically shut off after 45 minutes
to one hour of uninterrupted use. Simply restart the vacuum system with
the switch on the hose handle.
LED Indicator
(H10, H20 & H40 models)
LED – On low voltage connector
Steady green – indicates unit is connected to a power source
Information center
(H60 & H110 models)
Your central vacuum unit is equipped with an electronic timing device
which will recommend proper maintenance of your vacuum system.
These signals are only suggestions and will do not indicate a problem
with your vacuum system. They will not stop or hinder the use of the
vacuum.
Flashing LED - Empty dirt receptacle or change bag
Press 1 second to stop the flashing LED
Flashing LED - Have unit checked by service center




16
Maintenance
Motor
Please note that Riccar motors do not require lubrication. Each motor
contains two carbon brushes which will wear normally, and may eventu-
ally require replacement. For warranty purposes, this should be done by
an authorized service center. Brush life is affected by the number of hours
used, frequency of start-ups and shut-downs, humidity, altitude, and tem-
perature. In order to avoid damage to the motor itself, brushes should be
replaced before they are completely worn out. We therefore recommend
that you have your unit and motors inspected by a service center every
5-6 years.

17
Maintenance
Maintenance
Use with bag
Change the bag when the one in place is full. Frequency will depend on
the use of the unit. For the H60 & H110 models, the information center
will indicate when to change the bag. These indications are provided by
an electronic timing board, only as a reference guide.
1. To access the bag, unlatch the two clips and
remove the dust receptacle (figure 15).
2. Remove the used bag and seal bag opening
(adhesive seal provided on each bag). Discard
used bag.
3. Install the new bag, ensuring the tabs on the
bag adaptor are aligned with the slots in the
bag collar (figure 16).
4. Ensure adequate sealing by inserting bag as
far as the retention ring (figure17-A).
Rotate bag 20° (figure 17-B) to ensure tabs
on bag adaptor are no longer aligned with the
slots in the bag collar.
5. Replace dust receptacle and seal by latching
both clips.
Use only genuine Riccar replacement bags.
Failure to do so could
void the warranty on your vacuum unit.
retention ring
tabs on bag adaptator
A
B
gure 15
gure 16
gure 17

18
Maintenance
Maintenance
Use without bag
We recommend you empty the dust receptacle and clean the permanent
filter at least each season, depending on use of your central vacuum.
1. To empty the dust receptacle:
Disconnect the unit from the electric outlet.
Unlatch the two clips, remove the receptacle
(figure 18), and empty into an appropriate
container.
2. To clean the permanent filter (figure 19):
•Donotremovethefilter
 •Wrapthefilterandthelowerportionoftheunit
body within a large plastic bag. Hold it tightly
around the unit with one hand.
 •Withyourotherhand,gentlyshakethefilter.
 •Waitafewsecondsforthedusttosettle
before removing the plastic bag.
3. Replace the dust receptacle and seal with the
help of the two clips.
4. Reconnect the unit to the electric outlet.
Note:
Should the filter become stained, or emit an
unpleasant odor, it may be washed in cold
water (without bleach). Rinse and dry well
before replacing. Do not tumble dry.
gure 18
gure 19

19
Maintenance
Converting the Unit
Your Riccar central vacuum unit was designed for use with or without
disposable bag. Though it is sold with a bag installed, it can easily be
removed, and the unit modified for use without disposable bags.
1. Using a flat screwdriver, loosen the clamp collars
and remove the rubber coupling from the air
intake (see page 6, figure 4).
2. Unlatch the two clips and remove the dust
receptacle (see page 17, figure 15).
3. Remove the bag (see page 17).
4. Pull the bag adaptor out of the air intake
(see page 6, figure 5).
5. Put the other adaptor provided in the air intake
and, making sure that the tabs are aligned
with the notches, push it completely in
(figure 20).
6. Put the rubber coupling back on the air intake
and tighten the clamp collars using a flat
screwdriver.
7. The vacuum unit is now ready for use
without bag.
Note: this procedure is reversible at any time. For instructions on
installing the dust bag, please refer to page 17.
gure 20

20
Maintenance
Carbon Dust Filter
(H60 & H110 models)
We recommend changing this lter after three bag
replacements. The integrated monitor will indicate
when to change the lter. These indications are
provided by an electronic timing board, only as a
reference guide.
To do so:
1. Unlatch the opening on the carbon filter
case and gently flip it upward (figure 21).
2. Remove the used filter, and discard
(figure 22).
3. Insert the new filter. When doing so, please
ensure that the arrow printed on the filter
itself points outwards (figure 23).
4. Close casing, and latch.
gure 21
gure 23
gure 22