Richmat HJH55 Ble HANDSET User manual

HANDSET
HJH55 Ble

1. Remark:
1.Radio frequency handset
2.2x1.5V batteries
3.Effective distance: within 5m
4. Frequency range:2.402GHz-2.48GHz.
2. Dimension:(mm)

3. Remote control button diagram
ZG
SNORE
TV
Head（mm）
31
18
114
Foot（mm）
79
0
46
4.Remote control function description
Button
label
function
1
The bed bottom lamp is on/off (constant light).
2
Flashlight on/off (default 15s). Reuse function: ①Press
and hold the button for 5s, the backlight flashes, enter
the memory mode, press ZG/SNORE/TV/M1/M2 within 2s, the
buzzer "dididi" will sound, and the current motor
position, massager, and light bar can be memorized state.
②Press and hold the M1 + flashlight for 3s at the same
time, the backlight flashes twice, and all the keys on
the remote control enter the one-key release mode, which
can reset all the memory positions to the factory default

settings at the same time. ③Press and hold
FLAT+flashlight for 3s at the same time, the backlight
flashes three times, the buttons on all positions of the
remote control enter the continuous pressing mode,
release the button and the motor stops.
3
FLAT one-key reset, all motors retract to the minimum
stroke position, turn off the bed light, massager (no
reset after power on)
4
The head motor extends.
5
The motor runs to the ZG position with one key (there is
an initial value). Multiplexing function: long press the
flashlight for about 5s, the backlight flashes, press ZG
within 2s, the buzzer will sound 3 times, and record the
current motor position, massager, and light bar status
to ZG. (Not cleared after power failure)
6
The foot motor extends.
7
Head motor retracted
8
The motor runs to the SNORE position with one key (with
initial value). When the one-key release mode is timed
for 15 minutes, it will be leveled and the massager will
be turned off. Press any key to exit the timing;
continuous pressing mode has no timing. Multiplexing
function: long press the flashlight for about 5s, the
backlight flashes, press SNORE within 2s, the buzzer will
sound 3 times, and record the current motor position,
massager, and light bar status to SNORE. (Not cleared
after power failure)
9
Foot motor retracted
10
The motor runs to the M1 position with one key (initial
value is 0). Multiplexing function: long press the
flashlight for about 5s, the backlight flashes, press M1
within 2s, the buzzer will sound 3 times, and record the
current motor position, massager, and light bar status
to M1. (Not cleared after power failure)
11
The motor runs to the TV position (with an initial value)
with one button. Multiplexing function: long press the
flashlight for about 5s, the backlight flashes, press TV
within 2s, the buzzer will sound 3 times, and record the
current motor position, massager, and light bar status
to the TV. (Not cleared after power failure)
12
The motor runs to the M2 position with one key (initial
value is 0). Multiplexing function: long press the
flashlight for about 5s, the backlight flashes, press M2
within 2s, the buzzer will sound 3 times, and record the
current motor position, massager, and light bar status
to M2. (Not cleared after power failure)
13
If the head massager is not turned on, press the button
to turn on the massager. The default strength of the

massager is the strength when the massager was closed last
time. If the massager is turned on, press the button to
increase the strength of the head massager. There are 3
intensities, according to: Low->medium->high order, the
default time is 15 minutes, and it will continue to run
when it reaches the highest intensity.
14
TIME ON/OFF massager switch and timing button, press the
button to turn on the massager (the default intensity of
the massager is the intensity when it was last turned off,
timing time) and timing 15min -> timing 30min -> turn off
the massager and timing, timing time Displayed by two
indicator lights.
15
If the foot massager is not turned on, press the button
to turn on the massager. The default strength of the
massager is the strength of the last time it was closed.
If the massager is turned on, press the button to increase
the strength of the foot massager. There are 3
intensities, according to: Low->medium->high order, the
default time is 15 minutes, and it will continue to run
when it reaches the highest intensity.
16
Reduce the intensity of the head massager button, 3
intensity, when it reaches the lowest intensity, press
the massager again to turn off.
17
WAVE button: If the massager is not turned on, press the
button to turn on the massager. This button can make the
massager cycle between 4 modes: continuous-low-speed
wave-medium-speed wave-high-speed wave.
18
Decrease the intensity of the foot massager to 3 levels.
When it reaches the lowest intensity, press the massager
again to turn off.
Note: Press any button for more than 50s, the remote control will enter
sleep, release it and press it again to resume the function.
Coding method: ①Single control box/single remote control: Keep
pressing the head up and foot down buttons (4, 9) until the
backlight flashes to clear the remote control code matching
information; power on the control box again, the control box will be
in the code matching state within 60s , Keep pressing the head
down and foot up buttons (7, 6) of the remote control until you
hear the buzzer sound and the backlight flashes, indicating that
the code pairing is successful.
②Single control box to dual remote control: keep pressing the
head up and foot down buttons (4, 9) until the backlight flashes to
clear the remote control code matching information; power on the
control box again, the control box will be in the code matching
state within 60s , Keep pressing the head down and foot up

buttons (7, 6) of the remote control 1 until you hear the buzzer
sound and the backlight flashes, indicating that the remote control
1 is successfully paired; do not press any buttons on the remote
control 1, keep pressing the remote control The head down and
foot up buttons (7, 6) of the controller 2 until the buzzer sounds
and the backlight flashes, indicating that the remote controller 2 is
successfully paired. When the two remote controllers switch
control, you need to wait for the previous remote controller to
disconnect the Bluetooth connection. The latter can be controlled
by a remote control. ③Dual control box to dual
remote control: Use the instructions of "single control box/single
remote control" to pair system 1. Use "single control box/single
remote control" to explain pairing system 2. Unplug the power of
System 1 and System 2. Use a synchronization cable to connect
the two systems. Power on system 1 and system 2. Now, the two
beds will operate in synchronous mode. Note: 1. After the control
box is powered on for 60 seconds, you can press the code
matching key to start the code matching, the buzzer will beep
three times to enter the code matching state, and the control box
code matching key has no reset function 2. The backlight goes out
after 10s of inactivity on the remote control, and it sleeps after 15s
and the Bluetooth is disconnected. Press the button again to
reconnect the Bluetooth. 3. When the control box is powered on
for the first time or accidentally cut off, please reset it before using
it. 4. Double control box to double remote control, press one
remote control switch when switching the remote control key
mode, you can change the key mode of the two remote control at
the same time. Continuous pressing mode does not follow the
synchronization

Caution:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.