Ricmotech AP-Xtrem User manual

Page C-1
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
AP-Xtreme
Sim-Racing Chassis
Master Assembly Guide
SECTION C: Display Support Assembly

Page C-2
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
Refer to the main chassis you are assembling and advance
to the page indicated below.
APX-1000
(No Display)
Skip section C. Proceed to Section D.
Overhead Auxiliary Display
Proceed to next page.
APX-2000
(Single Display)
Proceed to page Error! Bookmark not
defined..
APX-3000
(Triple Display <32”)
Proceed to the next page.
APX-3000UW
(triple Display >32”)
Proceed to page 17.

Page C-3
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
This page applies when the overhead display mount is being
installed.
A5 x 2
W1 x 2
H2-1 x 2
CV1 BRK (Optional)
Install with larger hole
to top.
C2-1 x 2
W2 x 2
N2 x 2
C2-1 x 8
W2 x 8
N2 x 8
C2-2 x 2
W1 x 2
N1 x 2
E5VR
E5
Threaded
End Up
A9
A16 x 2
New
Compact
Style

Page C-4
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
APX-2000
(Single Display)
Proceed to next page.
APX-3000
(Triple Display <32”)
Proceed to page 7.
APX-3000UW
(triple Display >32”)
Proceed to page 17.

Page C-5
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
Install E5 unless E5VR was installed in the previous step.
C2-2 x 2
W1 x 2
N1 x 2
E5
A5 x 1
W1 x 1
H2-1 x 1

Page C-6
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
Install A9 for a single display.
DO NOT INSTALL THIS IF YOUR SIM IS CONFIGURED AS TRIPLE DISPLAY.
If you are building an APX-2000 (Single Display) then you are finished with this section. Proceed to Section D.
C2-1 x 2
W1 x 2
N1 x 2
A9 x 1

Page C-7
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
This page only applies to APX-3000.
Install the 2 vertical monitor rails using the hardware indicated.
C2-2 x 4
W2 x 4
N2 x 4
A5 x 2
W2 x 2
H2-1 x 2
E5 x 2
Threaded
End Up
If you have the
Dual Sensor VR
Option then
install E5VR with
CV1 Bracket

Page C-8
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
This page only applies to APX-3000.
Mount the transverse brackets at the same height using the hardware shown above. Snug the nuts to prevent the
brackets from sliding down, but do not overtighten.
C2-1 x 4
W2 x 4
N2 x 4
A6 x 2

Page C-9
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
This page only applies to APX-3000.
Mount the transverse rail to the transverse brackets using the hardware indicated above. Center the rail onto the
chassis and insure the rail is level. The rail is centered when there is exactly 7.5 inches overhanging on each side. Tighten
the nuts securely.
C2-1 x 4
W2 x 4
N2 x 4
E6

Page C-10
Revised: 3/9/2020
Last Edited by: FR
APX 1000+ Assembly Manual
This page only applies to APX-3000.
Mount the angle plates to the transverse bar as shown above using the hardware indicated.
C2-1 x 8
W2 x 8
N2 x 8
A7