RIDGID R6000-1 User manual

1 - English
This screwdriver has been engineered and manufactured to our high standard for dependability, ease of operation and operator safety.
When properly cared for, the drill will give you years of rugged, trouble-free performance.
WARNING
To reduce the risk of injury, the user must read and understand the operator’s manual before using this product.
Thank you for buying a RIDGID®product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE
Cet tournevis a été conçueet fabriqué conformément à nos
strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation. Correctement entretenu, il vous donnera des années
de fonctionnement robuste et sans problème.
AVERTISSEMENT
Pour réduire les risques de blessures, l’utilisateur doit
lire et veiller à bien comprendre le manuel d’utilisation
avant d’utiliser ce produit.
Merci d’avoir acheté un produit RIDGID®.
Su destornillador para paneles de yeso ha sido diseñado y
fabricado de conformidad con nuestras estrictas normas para
brindar fiabilidad, facilidad de uso y seguridad para el operador.
Con el debido cuidado, le brindará muchos años de sólido y
eficiente funcionamiento.
ADVERTENCIA
Para reducir el riesgo de lesiones, el usuario debe leer
y comprender el manual del operador antes de usar
este producto.
Le agradecemos la compra de un producto RIDGID®.
OPERATOR’S MANUAL
DRYWALL SCREWDRIVER
VARIABLE SPEED/REVERSIBLE
DOUBLE INSULATED
V
R6000-1
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

2 - English
Introduction ...................................................................................................................................................................... 2
Introduction / Introducción
General Safety Rules.....................................................................................................................................................3-4
Règles de sécurité générales / Reglas de seguridad generales
Specific Safety Rules........................................................................................................................................................ 4
Règles de sécurité particulières / Reglas de seguridad específicas
Symbols............................................................................................................................................................................ 5
Symboles / Símbolos
Electrical........................................................................................................................................................................... 6
Caractéristiques électriques / Aspectos eléctricos
Features............................................................................................................................................................................ 7
Caractéristiques / Características
Assembly.......................................................................................................................................................................7-8
Assemblage / Armado
Operation.......................................................................................................................................................................8-9
Utilisation / Funcionamiento
Maintenance..................................................................................................................................................................... 9
Entretien / Mantenimiento
Warranty ......................................................................................................................................................................... 10
Garantie / Garantía
Figure numbers (illustrations) ....................................................................................................................................11-12
Figure numéros (illustrations) / Figura numeras (ilustraciones)
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
INTRODUCTION
INTRODUCTION / INTRODUCCIóN
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

3 - English
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to
follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
WORK AREA
Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite the
dust or fumes.
Keep bystanders, children, and visitors away while
operating a power tool. Distractions can cause you to
lose control.
ELECTRICAL SAFETY
Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to install a
polarized outlet. Do not change the plug in any way.
Double insulation eliminates the need for the three-
wire grounded power cord and grounded power supply
system.
Avoid body contact with grounded surfaces such as
pipes, radiators, ranges, and refrigerators. There is an
increased risk of electric shock if your body is grounded.
Don’t expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of elec-
tric shock.
Do not abuse the cord. Never use the cord to carry the
tools or pull the plug from an outlet. Keep cord away
from heat, oil, sharp edges, or moving parts. Replace
damaged cords immediately. Damaged cords increase
the risk of electric shock.

When operating a power tool outside, use an outdoor
extension cord marked “W-A” or “W”. These cords
are rated for outdoor use and reduce the risk of electric
shock.
PERSONAL SAFETY
Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs, alcohol,
or medication. A moment of inattention while operating
power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry.
Contain long hair. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes, jewelry, or long
hair can be caught in moving parts.

Avoid accidental starting. Be sure switch is off
before plugging in. Carrying tools with your finger on the
switch or plugging in tools that have the switch on invites
accidents.
Remove adjusting keys or wrenches before turning
the tool on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. Proper footing and balance enables better
control of the tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, nonskid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
Do not wear loose clothing or jewelry. Contain long
hair. Loose clothes, jewelry, or long hair can be drawn
into air vents.
Do not use on a ladder or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
TOOL USE AND CARE
Use clamps or other practical way to secure and
support the workpiece to a stable platform. Holding
the work by hand or against your body is unstable and
may lead to loss of control.
Do not force tool. Use the correct tool for your
application. The correct tool will do the job better and
safer at the rate for which it is designed.
Do not use tool if switch does not turn it on or off.
Any tool that cannot be controlled with the switch is
dangerous and must be repaired.
Disconnect the plug from power source before making
any adjustments, changing accessories, or storing the
tool. Such preventive safety measures reduce the risk of
starting the tool accidentally.
Store idle tools out of the reach of children and other
untrained persons. Tools are dangerous in the hands of
untrained users.
Maintain tools with care. Keep cutting tools sharp
and clean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool’s operation. If damaged, have the tool
serviced before using. Many accidents are caused by
poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used
on another tool.
Keep the tool and its handle dry, clean and free from
oil and grease. Always use a clean cloth when clean-
ing. Never use brake fluids, gasoline, petroleum-based
products, or any strong solvents to clean your tool. Fol-
lowing this rule will reduce the risk of loss of control and
deterioration of the enclosure plastic.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

4 - English
Hold tool by insulated gripping surfaces when per-
forming an operation where the cutting tool may
contact hidden wiring or its own cord. Contact with a
“live” wire will make exposed metal parts of the cutting
tool “live” and shock the operator.
Know your power tool. Read operator’s manual care-
fully. Learn its applications and limitations, as well
as the specific potential hazards related to this tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Always wear safety glasses. Everyday eyeglasses
have only impact-resistant lenses; they are NOT
safety glasses. Following this rule will reduce the risk
of serious personal injury.
Protect your lungs. Wear a face or dust mask if the
operation is dusty. Following this rule will reduce the
risk of serious personal injury.
Protect your hearing. Wear hearing protection during
extended periods of operation. Following this rule will
reduce the risk of serious personal injury.
Inspect tool cords periodically and, if damaged, have
repaired at your nearest authorized service center.
Constantly stay aware of cord location. Following this
rule will reduce the risk of electric shock or fire.
Check damaged parts. Before further use of the
tool, a guard or other part that is damaged should
SERVICE
Tool service must be performed only by qualified
repair personnel. Service or maintenance performed by
unqualified personnel may result in a risk of injury.
WARNING!
To reduce the risk of injury, user must read
instruction manual.
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other conditions
that may affect its operation. A guard or other part that
is damaged should be properly repaired or replaced
by an authorized service center. Following this rule will
reduce the risk of shock, fire, or serious injury.
Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. A wire gauge size (A.W.G.) of at least 14 is
recommended for an extension cord 50 feet or less
in length. A cord exceeding 100 feet is not recom-
mended. If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the cord. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.
Inspect for and remove all nails from lumber before
using this tool. Following this rule will reduce the risk of
serious personal injury.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions
also.
GENERAL SAFETY RULES
When servicing a tool, use only identical replacement
parts. Follow instructions in the Maintenance section
of this manual. Use of unauthorized parts or failure to
follow Maintenance Instructions may create a risk of
shock or injury.
SPECIFIC SAFETY RULES
CALIFORNIA PROPOSITION 65
WARNING:
This product and some dust created by power sanding, sawing, grinding, drilling, and other construction activities
may contain chemicals, including lead, known to the State of California to cause cancer, birth defects, or other
reproductive harm. Wash hands after handling. Some example of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic particles.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

5 - English
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the tool better and safer.
Safety Alert Indicates a potential personal injury hazard.
V Volts Voltage
A Amperes Current
Hz Hertz Frequency (cycles per second)
min Minutes Time
Alternating Current Type of current
n
o
No Load Speed Rotational speed, at no load
Class II Tool Double-insulated construction
.../min Per Minute Revolutions, strokes, surface speed, orbits etc., per minute
Wet Conditions Alert Do not expose to rain or use in damp locations.
Read The Operator’s Manual To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Eye Protection Always wear eye protection with side shields marked to comply
with ANSI Z87.1 and a full face shield when operating this product.
Hot Surface To reduce the risk of injury or damage, avoid contact with any hot
surface.
SYMBOL NAME DESIGNATION/EXPLANATION
The following signal words and meanings are intended to explain the levels of risk associated with this product.
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SYMBOL SIGNAL MEANING
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

6 - English
ELECTRICAL
EXTENSION CORDS
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting in
overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter’s Laboratories
(UL) should be used.
When working outdoors with a product , use an extension
cord that is designed for outside use. This type of cord is
designated with “W-A” or “W” on the cord’s jacket.
Before using any extension cord, inspect it for loose or ex-
posed wires and cut or worn insulation.
**Ampere rating (on product data plate)
0-2.0 2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
Cord Length Wire Size (A.W.G.)
25'16 16 16 16 14 14
50'16 16 16 14 14 12
100'16 16 14 12 10 —
**Used on 12 gauge - 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING:
Keep the extension cord clear of the working area
Position the cord so that it will not get caught on
lumber, tools, or other obstructions while you are
working with a power tool. Failure to do so can
result in serious personal injury.
WARNING:
Check extension cords before each use. If
damagedreplace immediately. Never use the
product with a damaged cord since touching
the damaged area could cause electrical shock
resulting in serious injury.
DOUBLE INSULATION
Double insulation is a concept in safety in electric power
tools, which eliminates the need for the usual three-wire
grounded power cord. All exposed metal parts are isolated
from the internal metal motor components with protect-
ing insulation. Double insulated tools do not need to be
grounded.
WARNING:
The double insulated system is intended to protect
the user from shock resulting from a break in the
tool’s internal insulation. Observe all normal safety
precautions to avoid electrical shock.
NOTE: Servicing of a product with double insulation requires
extreme care and knowledge of the system and should be
performed only by a qualified service technician. For service,
we suggest you return the product to your nearest authorized
service center for repair. Always use original factory replace-
ment parts when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be
connected to a power supply that is 120 V, AC only (normal
household current), 60 Hz. Do not operate this product on
direct current (DC). A substantial voltage drop will cause a
loss of power and the motor will overheat. If the product
does not operate when plugged into an outlet, double-check
the power supply.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

7 - English
FEATURES
PRODUCT SPECIFICATIONS
Bit Shank.................................................................. 1/4 in.
Switch.........................................................Variable Speed
No Load Speed ..............................................0-4,000/min.
Input ...............................120 V, 60 Hz, AC only, 6.5 Amps
Net Weight.............................................................. 3.1 lbs.
KNOW YOUR DRYWALL SCREWDRIVER
See Figure 1, page 11.
The safe use of this product requires an understanding of
the information on the product and in this operator’s manual
as well as a knowledge of the project you are attempting.
Before use of this product, familiarize yourself with all op-
erating features and safety rules.
ADJUSTABLE NOSEPIECE
Your screwdriver has an adjustable nosepiece for varying
screw depth and easy bit changes.
BELT CLIP
A convenient belt clip is located on top of the motor
housing.
DUAL GRIP HANDLE
The soft-grip handle is designed with two grip position op-
tions for operator comfort and ease of handling.
FORWARD/REVERSE LEVER
The forward/reverse lever changes the direction of bit
rotation.
LOCK-ON BUTTON
The lock-on feature allows for continuous driving of screws
for extended periods of time.
MAGNETIC BIT HOLDER
The magnet holds the screwdriver bit and screws until you
are ready to drive them into drywall.
SWITCH TRIGGER
The switch trigger for your drywall screwdriver is conve-
niently located on the handle of the tool.
VARIABLE SPEED
The variable speed switch delivers higher speed with
increased trigger pressure.
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
WARNING:
Do not use this product if it is not completely
assembled or if any parts appear to be missing
or damaged. Use of a product that is not properly
and completely assembled could result in serious
personal injury.
Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-866-539-1710 for assistance.
PACKING LIST
Drywall Screwdriver with Magnetic Bit Holder
and #2 Phillips Bit installed
R2 Square Recess Screwdriver Bit
Operator’s Manual
WARNING:
If any parts are missing do not operate this tool
until the missing parts are replaced. Use of this
product with damaged or missing parts could
result in serious personal injury.
WARNING:
Do not attempt to modify this tool or create
accessories not recommended for use with this
tool. Any such alteration or modification is misuse
and could result in a hazardous condition leading
to possible serious personal injury.
WARNING:
Do not connect to power supply until assembly
is complete. Failure to comply could result in
accidental starting and possible serious personal
injury.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

8 - English
ASSEMBLY
INSTALLING AND REPLACING BIT HOLDER
AND BITS
See Figure 2, page 11.
To install or replace bits:
Install 1/4 in. screwdriver bits by inserting them into the
magnetic bit holder.
NOTE: It is not necessary to remove the adjustable nose-
piece to install or remove bits.
Replace 1/4 in. screwdriver bits by pulling them out of
the magnetic bit holder.
To remove the magnetic bit holder:
Pull the adjusting sleeve. The adjusting sleeve and adjust-
able nosepiece come off the gear casing as a set.
Remove the magnetic bit holder. Pull the bit holder out
with pliers if you cannot remove it by hand.
To reassemble the bit holder and nosepiece:
Push the bit holder into the hex opening of the spindle
until the ball lock snaps into the groove in the bit holder
shank.
Attach the adjustable nosepiece to the gear case. Align
the raised tab inside the adjustable nosepiece with the
groove on the gear case and push the nosepiece until it
snaps into place.
OPERATION
WARNING:
Do not allow familiarity with tools to make you
careless. Remember that a careless fraction of a
second is sufficient to inflict severe injury.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes, resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories
not recommended by the manufacturer of this
tool. The use of attachments or accessories not
recommended can result in serious personal
injury.
APPLICATIONS
You may use this tool for the purposes listed below:
Driving screws in drywall
STARTING/STOPPING THE SCREWDRIVER
See Figure 3, page 11.
To turn the screwdriver ON, depress the switch trigger. Re-
lease the switch trigger to turn the screwdriver OFF.
VARIABLE SPEED
The screwdriver has a variable speed switch for operator
control of speed and torque limits.
Depress the switch trigger all the way for maximum speed
and torque. Depress the switch trigger only part of the way
for less speed and torque.
Avoid running the tool at low speeds for extended periods
of time. Constant use at low speeds may cause overheating.
If this occurs, cool the screwdriver by running it without a
load and at full speed.
LOCK-ON BUTTON
See Figure 3, page 11.
The screwdriver is equipped with a lock-on feature which
is convenient for continuous driving of screws for extended
periods of time. To lock-on, depress the switch trigger, push
in and hold the lock-on button located on the side of the
handle, then release switch trigger. Release the lock-on but-
ton and the screwdriver will continue running.
To release the lock, depress the switch trigger and re-
lease.
If you have the lock-on feature engaged during use and the
screwdriver becomes disconnected from the power supply,
disengage the lock-on feature immediately.
FORWARD/REVERSE LEVER
See Figure 4, page 11.
The direction of rotation of the bit is controlled by a lever
located above the switch trigger. With the screwdriver held
in normal operating position, the direction of rotation lever
should be positioned to the left of the switch for forward
driving operation. The direction of rotation is in reverse when
the lever is to the right of the switch.
NOTE: The screwdriver will not run unless forward/reverse
lever is pushed fully to the left or right. The design of the
switch will not permit changing the direction of rotation while
the screwdriver is running. Release the switch trigger and al-
low the screwdriver to stop before changing its direction.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

9 - English
OPERATION
SETTING DEPTH
See Figure 5, page 12.
The adjustable nosepiece of your tool will automatically drive
screws to preset depths. It may be helpful to begin each new
job by driving several test screws in scrap material to check
and adjust the depth setting.
To make preset depth adjustments:
Rotate the adjusting sleeve until you obtain the desired
depth for the bit holder or screwdriver bit.
Test drive a screw in scrap material to determine if it is
correct.
Adjust as necessary to increase or decrease the desired
depth.
DRIVING SCREWS
See Figures 6 - 7, page 12.
There are two two options for gripping the handle of the
screwdriver, determined by operator comfort and working
angle.
The screwdriver has a variable speed switch for operator
control of speed and torque limits.
Be sure the screwdriver is in the OFF position before
connecting it to the power supply.
Check the direction of rotation lever for correct setting
(forward or reverse).
Secure the workpiece. Use clamps if necessary.
Plug the screwdriver into power supply source.
Depress the switch trigger to start the screwdriver. Do
not lock the switch ON for jobs where the screwdriver
may need to be stopped suddenly.
Hold the screwdriver firmly and place the bit and screw
at the point to be driven.
NOTE: The bit holder is magnetized and will hold most
commercial drywall screws.
Apply quick, snap action type pressure to the bit. The
pressure applied will engage the clutch and drive the
screw.
MAINTENANCE
WARNING:
When servicing use only identical RIDGID
replacement parts. Use of any other parts may
create a hazard or cause product damage.
WARNING:
Always wear eye protection with side shields
marked to comply with ANSI Z87.1. Failure to do
so could result in objects being thrown into your
eyes, resulting in possible serious injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may
result in serious personal injury.
Electric tools used on fiberglass material, wallboard, spack-
ling compounds, or plaster are subject to accelerated wear
and possible premature failure because the fiberglass chips
and grindings are highly abrasive to bearings, brushes,
commutators, etc. Consequently, we do not recommended
using this tool for extended work on these types of materials.
However, if you do work with any of these materials, it is ex-
tremely important to clean the tool using compressed air.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrica-
tion is required.
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

11
Fig. 1
Fig. 2
Fig. 3 Fig. 4
A
C
BE
F
DA - Adjustable nosepiece (butée réglable, punta ajustable)
B - Belt clip (clip de ceinture, clip para el cinto)
C - Magnetic bit holder (porte embout magnétique,
portapuntas magnético)
D - Forward/reverse lever (inverseur de sens de rotation,
palanca de marcha adelante/atrás)
E - Lock-on button (bouton de verrouillage, botón del
seguro de encendido)
F - Switch trigger (gâchette de commutateur, gatillo del
interruptor)
A - 1/4 in. phillips screwdriver bit (embout philips de
6,4 mm [1/4 po], punta de destornillador phillips
de 6,4 mm [1/4 pulg.])
B - Pull to remove adjustable nosepiece (tirer pour enlever
la tête réglable, para desmontar la punta ajustable, tire
de la misma)
C - Adjusting sleeve (manchon de réglage, collar de
ajuste)
D - Groove (rainure, ranura)
E - Belt clip (clip de ceinture, clip para el cinto)
F - Gear casing (boîtier d’engrenages, caja de
engranajes)
G - Magnetic bit holder with 1/4 in. hex opening (porte-
embout magnétique avec ouverture hexagonal de 6,4
mm [1/4 po]; portapuntas magnético con abertura
hexagonal de 6,4 mm [1/4 pulg.])
H - Align and push to replace adjustable nosepiece
(aligner la tête réglable et appuyer pour la remettre en
place, para volver a montar la punta ajustable, alinéela
y empújela)
I - Adjustable nosepiece (tête réglable, punta ajustable)
J - R2 bit (embout r2, punta r2)
G
F
B
C
H
A
I
D
E
J
B
C
A
B
A
A - Forward/reverse lever (inverseur de sens de rotation,
palanca de marcha adelante/atrás)
B - Lock-on button (bouton de verrouillage, botón del
seguro de encendido)
C - Switch trigger (gâchette de commutateur, gatillo del
interruptor)
A - Reverse (marche arrière, marcha atrás)
B - Forward (marche avant, marcha adelante)
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30

12
Fig. 5 Fig. 6 Fig. 7
A
B
C
A - To decrease depth of screwdriver bit (pour
réduire la profondeur de l’embout, para
disminuir la profundidad de la punta de
destornillador)
B - To increase depth of screwdriver bit (pour
augmenter la profondeur de l’embout, para
aumentar la profundidad de la punta de
destornillador)
C - Preset depth setting of screwdriver bit
(réglage de la profondeur de l’embout,
profundidad prefijada de la punta de
destornillador)
www.calcert.com [e-mail]1.888.610.7664 0
5
10
15
20
25
30