RIDGID RT12000 User manual

Part No. SP7054
Wet/Dry Vacs
WET/DRY VAC PARTS
& ACCESSORIES
1-800-474-3443
Call Us 1st
• Operation
• Warranty (See back cover)
• Technical Assistance
• Repair Parts
For any questions about:
Please have your Model Number and
Serial Number on hand when calling.
12 U.S. GALLON / 45 Liter
WET/DRY VAC
OWNER’S MANUAL
WARNING:
To reduce the risk of injury,
the user must read and
understand the owner’s
manual before using this
product.
!
RT12000
D
R
A
I
N
D
R
A
IN
TABLE OF CONTENTS
*****************
• SAFETY INSTRUCTIONS...........2
• INTRODUCTION ..................4
• ASSEMBLY......................6
• OPERATION .....................9
• STORAGE......................13
• MAINTENANCE..................14
• REPAIR PARTS .................16
SP7054 RT12000.indb 1
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com

2
IMPORTANT SAFETY INSTRUCTIONS
Safety is a combination of using common
sense, staying alert, and knowing how your
Wet/Dry Vacuum Cleaner (“Vac”) works.
Safety Signal Words
DANGER: Indicates a hazardous
situation which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a hazardous
situation which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a hazardous
situation which, if not avoided, could
result in minor or moderate injury.
When using your Vac, always follow basic
safety precautions including the following:
WARNING
- To reduce the risk of fire,
electric shock, or injury:
• Read and understand this manual and
all labels on the Wet/Dry Vac before
operating.
• Use only as described in this manual.
• Do not leave Vac running while
unattended - you may fail to notice
important signs indicating abnormal
operation such as loss of suction, debris/
liquid exiting exhaust, or abnormal
motor noises. Immediately stop using
Vac if you notice these signs.
• Do not leave Vac when plugged in.
Unplug from outlet when not in use and
before servicing.
• Sparks inside the motor can ignite
flammable vapors or dust. To reduce the
risk of fire or explosion, do not use near
combustible liquids, gases, or dusts,
such as gasoline or other fuels, lighter
fluid, cleaners, oil-based paints, natural
gas, coal dust, magnesium dust, grain
dust, aluminum dust, or gun powder.
• Do not vacuum anything that is burning
orsmoking,suchascigarettes,matches,
or hot ashes.
• To avoid the risk of self-ignition of drum
debris, empty drum after each use.
Combustible materials, such as rags or
sawdust containing stain or urethane,
can be sources of such overheating.
!
!
!
!
• Do not vacuum drywall dust, cold
fireplace ash, or other fine dusts with
standard filter. These may pass through
the filter and be exhausted back into the
air. Use a fine dust filter instead.
• To reduce the risk of inhaling toxic
vapors, do not vacuum or use near toxic
or hazardous materials.
•To reduce the risk of electric shock,
do not expose to rain or allow liquid to
enter motor compartment. Store indoors.
• This Wet/Dry Vac is not intended for
use by persons (including children) with
reduced physical, sensory, or mental
capabilities, or lack of experience
and knowledge, unless they have
been given supervision or instruction
concerning use of the appliance by a
person responsible for their safety.
•Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
• Do not use with a torn filter or without
filter installed except when vacuuming
liquids as described in this manual.
Dry debris ingested by the impeller may
damage the motor or be exhausted into
the air.
• Turn off Vac before unplugging.
• To reduce the risk of injury from
accidental starting, unplug power cord
before changing or cleaning filter.
• Do not unplug by pulling on cord.
To unplug, grasp the plug, not the cord.
• Do not use with damaged cord, plug or
other parts. If your Vac is not working
as it should, has missing parts, has
been dropped, damaged, left outdoors,
or dropped into water, call customer
service.
• Do not pull or carry by cord, use cord
as handle, close a door on cord, or pull
cord around sharp edges or corners.
Do not run Vac over cord. Keep cord
away from heated surfaces.
• Do not handle plug, switch, or the Vac
with wet hands.
SP7054 RT12000.indb 2 9/5/18 12:04 PM

3
IMPORTANT SAFETY INSTRUCTIONS
• Use only extension cords that are rated
for outdoor use. Extension cords in poor
condition or too small in wire size can
pose fire and shock hazards. To reduce
the risk of these hazards, be sure the
cord is in good condition and that liquid
does not contact the connection. Do not
use an extension cord with conductors
smaller than 1,3 mm2(16 AWG).
• This Wet/Dry Vac is double-insulated,
eliminating the need for a separate
grounding system. Use only identical
replacementparts.Read the instructions
for Servicing Double-Insulated Wet/Dry
Vacs before servicing.
• Do not put any object into ventilation
openings. Do not vacuum with any
ventilation openings blocked; keep free
of dust, lint, hair or anything that may
reduce air flow.
• Keep hair, loose clothing, fingers, and
all parts of body away from openings
and moving parts.
• To reduce the risk of falls, use extra
care when cleaning on stairs.
• To reduce the risk of back injury or falls,
do not lift a Vac that is heavy with liquid
or debris. Partially empty by scooping
debris or draining liquid.
• To reduce the risk of personal injury
or damage to Vac, use only RIDGID
recommended accessories.
• When using as a blower:
- Direct air discharge only at work area.
- Do not direct air at bystanders.
- Keep children away when blowing.
- Do not use blower for any job except
blowing dirt and debris.
- Do not use as a sprayer.
•To reduce the risk of eye injury, wear
safety eyewear. The operation of any
utility Vac or blower can result in foreign
objects being blown into the eyes, which
can result in severe eye damage.
Observe the following warnings that
appear on the motor housing of your Vac:
WARNING: To reduce the risk of
electric shock - do not expose to
rain - store indoors.
DOUBLE INSULATED
GROUNDING NOT REQUIRED.
WHEN SERVICING USE ONLY
IDENTICAL REPLACEMENT PARTS.
!
SAVE THIS MANUAL
CAUTION:
•To reduce the risk of hearing damage,
wear ear protectors when using for
extended hours or in a noisy area.
•For dusty operations, wear dust mask.
•Static shocks are common when the
relative humidity of the air is low.
Vacuuming fine debris with your Vac can
deposit static charge on the hose or Vac.
To reduce the frequency of static shocks
in your home or when using this Vac, add
moisture to the air with a humidifier.
!
WARNING:
• For your own safety, read and
understand owner’s manual.
• Do not run unattended.
• Do not pick up hot ashes,
coals, toxic, flammable or other
hazardous materials.
• Do not use around explosive
liquids or vapors.
!
SP7054 RT12000.indb 3 9/5/18 12:04 PM

4
This Wet/Dry Vac is intended for house-
hold use. It may be used for vacuuming
wet or dry media and may be used as a
blower.
Getting to Know Your Wet/Dry Vac
Read this Owner’s Manual to familiarize
yourself with the product features and
to understand the specific usage of your
new Vac.
INTRODUCTION
Professional Locking Hose - Provides
transfer of vacuum or blowing capability
to work site. Provides the means of
attaching Extension Wands and Nozzles.
Locking Hose 48mm (1 7/8”) x 2.4 m (8’) -
Fits 2 1/2” Accessories.
Extension Wands - These Wands can
be connected together and provide
additional length.
Wet Nozzle - Used for wet pickup on
smooth surfaces to pick up liquid and dry
the surface in one stroke.
Utility Nozzle - General purpose Nozzle
for most vacuuming applications.
Car Nozzle - Dry pickup Nozzle for car
interiors and most upholstery cleaning.
Familiarize yourself with the Accessories included with the Vac. Each Accessory may be
used in various ways for vacuuming and blowing debris. Here is a list of the Accessories
and their uses.
D
R
AI
N
D
R
A
IN
Powerhead Assembly
Carry Handle /
Power Cord Wrap
Drain
Caster
Drum Latch
Dust Drum
Vac Inlet
Caster Foot
Storage
ON/OFF Switch
Blower Port
SP7054 RT12000.indb 4 9/5/18 12:04 PM

5
D
R
A
I
N
D
R
A
I
N
A
D
E
B
C
F
G
J
K
L
H
I
M
Unpacking
Carton Contents List
Key Description Qty
A Wet/Dry Vac ...............................1
B Carry Handle................................1
C Pan Head Screws, #10 x 3/4”
(19 mm)....................................6
D Hose Storage Clips .....................2
E Caster Foot w/Storage.................4
F Casters ........................................4
G* Qwik Lock™ Filter .......................1
H Professional Locking Hose..........1
I Extension Wands.........................2
J Utility Nozzle................................1
K Wet Nozzle ..................................1
L Car Nozzle...................................1
M Owner’s Manual...........................1
* The Filter comes preassembled.
This Product Requires Assembly.
Check all parts from carton against the
Carton Contents List.
If any parts are damaged or missing, contact
1-800-4-RIDGID (US and Canada) or by
email at [email protected].
INTRODUCTION
Phillips Screwdriver
Tools Required
SP7054 RT12000.indb 5 9/5/18 12:04 PM

6
ASSEMBLY
NOTE: Remove Powerhead Assembly
from Dust Drum prior to assembly of
Casters and Caster Feet.
1. Turn Dust Drum upside down on floor.
2. Place Caster Foot on floor. Insert the
stem of a Caster into socket of Caster
Foot.
3. Push on the Caster until the Caster ball
end snaps fully into the Socket and the
Caster swivel freely. Repeat for other
three Casters and Caster Feet.
4. Place Caster Foot with Caster over
post on bottom of Dust Drum and press
firmly in place, as shown.
5. Repeat for the other three Caster/
Caster Foot assemblies.
6. Turn the Dust Drum upright.
Caster/Caster Foot Assembly Wet/Dry Vac Assembly
Caster
Foot
Caster
Caster Ball
Caster Stem
Caster Foot
Post Hole
Caster Foot
Post
Dust
Drum
2. Press in on the two Latches located
on either side of the Dust Drum until
they snap into place, securing the
Powerhead Assembly to the Dust Drum.
3. To remove the Powerhead Assembly,
pull out on the two Latches and lift
Powerhead Assembly from the Dust
Drum. Do not force the Latches to
rotate more than slightly outside Drum
Flange.
Drum
Latches
(1 on each
side)
Dust Drum
Powerhead
Assembly
Attaching Powerhead Assembly
to Dust Drum
1. Place Powerhead Assembly on top of
Dust Drum with the Extended Lip of the
Lid aligned with the Vac Inlet. Be sure
Powerhead Assembly is fully seated on
the Dust Drum.
Extended
Lip
Vac
Inlet
Dust
Drum
Powerhead
Assembly
SP7054 RT12000.indb 6 9/5/18 12:04 PM

7
ASSEMBLY
Carry Handle
Powerhead
Assembly
#10 x 3/4"
(19 mm) Pan
Head Screws (2)
Extended
Flange
#10 x 3/4"
(19 mm)
Pan Head
Screws (2)
Hose Clips
(1 on each side)
Powerhead
Assembly
Carry Handle Assembly
1. Locate the Carry Handle and the two
(2) #10 x 3/4” (19 mm) Pan Head
Screws in loose parts bag.
2. Position the Carry Handle on top of the
Powerhead Assembly, with the Carry
Handle Extended Flange to the rear of
the Powerhead Assembly, as shown.
3. Insert a #10 x 3/4” (19 mm) Pan Head
Screw through the hole at each end of
theCarryHandleandintothePowerhead
Assembly. Tighten securely.
Hose Storage Clip Assembly
1. Locate the two (2) Hose Clips and
four (4) #10 x 3/4” (19 mm) Pan Head
Screws in the loose parts.
2. Place a Clip into the recess next to one
of the Latches. The Curve of the Clip
should face outward.
3. Insert a #10 x 3/4” (19 mm) Pan Head
Screw into each mounting hole and
tighten securely.
4. Repeat on the other side.
SP7054 RT12000.indb 7 9/5/18 12:04 PM

8
ASSEMBLY
Extension Wand
Release Button
Accessory Nozzle
Ridges
CONNECT:
Locking Accessories
1. To Connect Accessory: Your
RIDGID Wet/Dry Vac includes Locking
Accessories to prevent the Accessories
from falling off when in use. To
connect the Accessories, align the
Nozzle Ridges of the Accessory with
the Release Button of your Extension
Wand. Press to secure the Nozzle to
the Extension Wand.
2. To Disconnect Accessory: Twist
the Nozzle and Extension Wand to
disengage the Nozzle Ridges and pull.
You may also press the Release Button
and pull to disengage.
Accessory Nozzle
Ridges
Extension Wand
Release Button
DISCONNECT:
Inserting the Professional
Locking Hose
1. Locate the end of the Professional
Locking Hose and align it with the Drum
Inlet. Align the Hose Release Button with
the Ridges on the Vac Inlet. Push the
Hose end straight into the Vac Inlet until
the Hose Release Button fully engages
the Inlet Ridges.
2. To remove Hose, rotate the end of the
Professional Locking Hose in
either direction to release the
Hose Latch from the Inlet Ridges.
Press the Hose Release Button and
pull the Hose end straight out of the
Vac Inlet.
D
R
A
I
N
Drum
Vac Inlet
Ridges
Professional
Locking Hose
Hose
Release Button
SP7054 RT12000.indb 8 9/5/18 12:04 PM

9
1
1
Inlet Ridges
Hose Release Button
2INSERT
HOSE
REMOVE
HOSE
Remove Hose:
1. Rotate Hose End in either direction to
disengage Inlet Ridges.
2. Press the Hose Release Button and
pull the Hose End straight out of the
Vac Inlet.
OPERATION
!
!
WARNING: To reduce the risk of fire, explosion, or damage to Vac:
• Do not leave Vac running while unattended - you may fail to notice important
signs indicating abnormal operation such as loss of suction, debris/liquid
exiting the exhaust, or abnormal motor noises. Immediately stop using Vac
if you notice these signs.
• Do not leave Vac plugged in when not in use.
• Do not continue running when float has cut off suction.
• Sparks inside the motor can ignite airborne flammables. Do not operate
Vac near flammable liquids or in areas with flammable gases, vapors, or
explosive/airborne dust. Flammable liquids, gases, and vapors include:
lighter fluid, solvent-type cleaners, oil-based paints, gasoline, alcohol, and
aerosol sprays. Explosive dusts include: coal, magnesium, aluminum,
grain, and gun powder.
• Do not vacuum up explosive dusts, flammable liquids, or hot ashes.
• Do not leave sawdust or rags with stain or polyurethane residue inside Vac.
Empty drum after picking up these potentially self-heating materials.
WARNING: To reduce the risk of electric shock or injury:
• Do not expose to rain or allow liquid to enter motor compartment.
Store indoors.
• Do not handle plug, switch, or Vac with wet hands.
• Unplug Vac before servicing. If your Vac is not working as it should, has
missing parts, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center or call customer service.
• When using an extension cord, use only outdoor-rated cords that are in
good condition. Do not allow the connection to come into contact with
liquid.
ASSEMBLY
SP7054 RT12000.indb 9 9/5/18 12:04 PM

10
OPERATION
Vacuuming Dry Materials
1. The Filter must always be correctly
installed to avoid leaks and possible
Vac damage.
2. To maintain peak performance when
vacuuming fine dust, clean the Drum
and Filter regularily.
NOTE: Do not use a wet Filter when
picking up dry material. The Filter will
quickly clog and be difficult to clean.
3. If the Filter is wet, you must allow it to
dry completely or replace it with a dry
Filter before using the Vac to pick up
dry material.
Polarized Plug
To reduce the risk of electric shock, this
Vac has a Polarized Plug (one blade is
wider than the other). This Plug will fit in
a Polarized Outlet only one way. If the
Plug does not fit fully in the Outlet, reverse
the Plug. If it still does not fit, contact a
qualified electrician to install the proper
Outlet. Do not change the Plug in any way.
With Power Cord plugged in, turn the Vac
“ON” by pressing in on the “I” (top) on the
Power Switch. To turn “OFF” press the
“O” (bottom) of the Power Switch. The
symbols used on the Switch Actuator are
international “On & Off” symbols.
ON/OFF
Switch
CAUTION: To reduce the risk of hearing damage, wear ear protectors
when using the Vac/Blower for extended time or in a noisy area.
!
SP7054 RT12000.indb 10 9/5/18 12:04 PM

11
OPERATION
Emptying the Dust Drum
1. Unplug Power Cord from power source.
2. The Vac comes equipped with a Drain
for easy emptying of liquids. Position
the Vac near a suitable drain or
receptacle and remove the Drain Cap.
3. Remove the Powerhead Assembly by
pulling outward at the top of the two
Latches.
4. Lift Powerhead Assembly from the
Dust Drum and set aside.
5. Empty Dust Drum into a proper waste
disposal container.
WARNING: To reduce the risk
of injury from accidental starting,
unplug power cord before emptying
the drum.
D
R
A
I
N
D
R
A
IN
Drain Cap
Dust
Drum
Drum Latches (2)
!
Vacuuming Liquids
1. Vacuuming up small amounts of liquid
(less than 2” (5 cm) collected in Dust
Drum) does not require Filter removal.
2. When larger amounts of liquid are to
be picked up, remove the Filter, but
not the Filter Cage or Float, to prevent
the Filter from becoming saturated with
liquid. If the Filter becomes saturated,
you may see “mist” coming from the
Blowing Port.
3. When the Drum is “full” the Float will
rise and cut off airflow. The motor
sound will rise in pitch and its speed
will increase indicating the Drum is
“full”. Turn OFF the Vac and unplug the
power cord before emptying the Drum.
4. Following use of Vac for wet pick up,
allow Filter to dry completely to avoid
mildew and Filter damage.
WARNING: Do not operate
without filter cage and float in place.
They prevent liquid from entering the
impeller and damaging the motor.
IMPORTANT: To reduce the risk of
damage to the Vac, do not run Motor with
Float in raised position.
!
SP7054 RT12000.indb 11 9/5/18 12:04 PM

WARNING: Always wear safety
eyewear complying with ANSI Z87.1
(or in Canada, CSA Z94.3) before
using as a blower.
CAUTION: Wear a dust mask if
blowing creates dust which might
be inhaled.
WARNING: To reduce the risk
of injury to bystanders, keep them
clear of blowing debris.
12
!
!
!
Blowing Feature
Your Vac features a Blower Port. It can
blow sawdust and other debris. Follow the
steps below to use your Vac as a Blower.
1. Locate the Blower Port, at the rear of
the Powerhead of your Wet/Dry Vac.
2. Align the Professional Locking Hose
Release Button end with the Blower
Port Ridges. Push the Hose End
straight into the Blower Port until the
Hose Release Button fully engages the
Blower Port Ridges.
3. (Optional) Attach the Extension Wand
to swivel end of the Hose.
4. Turn the Vac on and you are ready to
use your Vac as a Blower.
Extension
Wand
(Optional)
Swivel End of Hose
Blower
Port
Ridges
Professional
Locking Hose
Hose Release Button
Remove Hose:
1. Rotate Hose End in either direction to
disengage Blower Port Ridges.
2. Press the Hose Release Button and
pull the Hose End straight out of the
Blower Port.
INSERT HOSE
REMOVE HOSE
1
2
Blower
Port
Ridges
Hose Release Button
1
OPERATION
SP7054 RT12000.indb 12 9/5/18 12:04 PM

13
Accessory Storage
1. For storage, slide the Extension Wands
and the Accessories onto Posts of the
Caster Feet.
2. To remove Wands and Accessories,
lightly rotate and pull upward.
ACCESSORY & HOSE STORAGE
Hose Storage
The Professional Locking Hose may be
stored around the Powerhead Assembly
using the two Hose Storage Clips.
D
R
AI
N
Cord &
Plug
Handle/
Cord Wrap
Tabs
Cord Clip
Professional
Locking Hose
Powerhead
Assembly
Hose Storage Clips (2)
Cord Storage
To store the Cord, wrap it around the top
Handle/Cord Wrap beneath the two Tabs.
Secure the Cord using the Cord Clip on
the Plug.
WARNING: Do not put any
object into ventilation openings.
Do not vacuum with any ventilation
openings blocked; keep free of dust,
lint, hair or anything that may reduce
air flow.
CAUTION:Donotoperatevacuum
while the hose is still wrapped
around the powerhead assembly in
the storage position.
!
!
D
R
A
I
N
D
R
A
I
N
Accessory
Storage Post
Caster
Feet (4)
SP7054 RT12000.indb 13 9/5/18 12:04 PM

14
MAINTENANCE
NOTE: The Filter is made of high quality
paper designed to stop small particles of
dust. The Filter can be used for dry pick
up or small amounts of liquid. Handle the
Filter carefully when removing or installing
it. Creases in the Filter Pleats may occur
from installation but will not affect the
performance of the Filter.
NOTE: Failure to properly seat the
bottom Gasket and Integrated Filter Plate
to the Filter Cage could result in debris
bypassing the Filter.
WARNING: To reduce the risk
of injury from accidental starting,
unplug power cord before changing
or cleaning filter.
Filter Removal:
1. Place fingers under the two Filter Tabs.
2. While pressing down with one thumb
on the Qwik Lock™ Stud that protrudes
through the center of the Filter Plate,
lift up on the Tabs until Filter releases.
3. Slide Filter off Filter Cage.
IMPORTANT: To avoid Blower Wheel
and Motor Damage always reinstall Filter
before using Vac for dry pickup.
Filter Installation:
1. Slide the Qwik Lock™ Filter over the
Filter Cage while aligning the Qwik
Lock™ Stud on the Filter Cage with
the center hole in the Qwik Lock™
Integrated Filter Plate.
2. Make sure the Rubber Gasket at the
bottom of the Qwik Lock™ Filter seats
around the base of the Filter Cage.
3. FirmlypresstheQwikLock™Integrated
Filter Plate down around the Qwik
Lock™ Stud until it snaps into place.
WARNING: Do not operate
without filter cage and float, as they
prevent liquid from entering the
impeller and damaging the motor.
Qwik Lock™
Stud
Rubber
Gasket at
Bottom of
Filter
PUSH
DOWN
PULL
UP
Filter
Tabs (2)
Integrated Filter Plate
with Center Hole
PULL
UP
Filter Cage
Float
Powerhead
Assembly
Your Filter should be cleaned often to
maintain peak Vac performance.
Filter
Removal & Installation of the
Qwik Lock™ Filter
!
!
SP7054 RT12000.indb 14 9/5/18 12:04 PM

15
MAINTENANCE
Cleaning A Dry Filter
1. Some removal of dry debris can be
accomplished without removing the
Filter from the Vac. Slap your hand on
top of the Lid while the Vac is turned
off.
2. For best cleaning results due to
accumulated dust, clean the Filter in
an open area. Cleaning SHOULD be
done outdoors and not in the living
quarters.
3. After Filter removal from Vac, remove
the dry debris by gently tapping Filter
against the inside wall of your Dust
Drum. The debris will loosen and fall.
4. For thorough cleaning of Dry Filter
with fine dust (no debris), run water
through it as described under “Cleaning
A Wet Filter”.
Cleaning A Wet Filter
After Filter is removed, run water through
the Filter from a hose or spigot. Take care
that water pressure from the hose is not
strong enough to damage Filter.
IMPORTANT: After cleaning, check the
Filter for tears or small holes. Do not use a
Filter with holes or tears in it. Even a small
hole can allow dust to come out of your
Vac. Replace it immediately.
Allow the Filter to dry completely before
reinstalling and storing the Vac or picking
up dry debris.
WARNING: To assure product SAFETY and RELIABILITY, any other
maintenance, repairs and adjustments should be performed by Authorized Service
Centers, always using RIDGID replacement parts.
!
SP7054 RT12000.indb 15 9/5/18 12:04 PM

WARNING
SERVICING OF DOUBLE-INSULATED WET/DRY VAC
In a double-insulated Wet/Dry Vac, two systems of insulation are provided
instead of grounding. No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added. Servicing a double-
insulated Wet/Dry Vac requires extreme care and knowledge of the system,
and should be done only by qualified service personnel. Replacement
parts for a double-insulated Wet/Dry Vac must be identical to the parts
they replace. Your double-insulated Wet/Dry Vac is marked with the words
“DOUBLE INSULATED” and the symbol (square within a square) may
also be marked on the appliance.
To reduce the risk of injury from electrical shock, unplug power cord before
servicing the electrical parts of the Wet/Dry Vac.
!
12 U.S. Gallon (45 Liter)
Wet/Dry Vac
Model Number RT12000
!
WARNING: To reduce the risk of injury from electrical shock, unplug power
cord before servicing the electrical parts of the Wet/Dry Vac.
!
WARNING: All disassembly and repairs should be performed by qualified
personnel.
REPAIR PARTS
This product has a 90 day Satisfaction Guarantee Policy
as well as a Limited Lifetime Warranty.
Form No. SP7054 Printed in Mexico 08/18
©2018 Emerson
Part No. SP7054
SP7054 RT12000.indb 16 9/5/18 12:04 PM
99 Washington Street
Melrose, MA 02176
Phone [phone]
Toll Free 1-800-517-8431
Visit us at www.TestEquipmentDepot.com