Riello 3898350 Quick start guide

Installation, use and maintenance instructions

20041914 (11) - 07/2016

Forced draught gas burners

Modulating operation

CODE MODEL TYPE

3898350 RS 300/EV BLU 849 T2

3898452 RS 400/EV BLU 850 T2

3899152 RS 500/EV BLU 856 T2

20040547 RS 650/EV BLU 1123 T2

3911090 RS 800/EV BLU 887 T2

Translation of the original instructions

1 20041914

Contents

1 Declarations................................................................................................................................................................................ 3

2 Information and general warnings............................................................................................................................................ 4

2.1 Information about the instruction manual.................................................................................................................... 4

2.1.1 Introduction.................................................................................................................................................................. 4

2.1.2 General dangers.......................................................................................................................................................... 4

2.1.3 Other symbols............................................................................................................................................................. 4

2.1.4 Delivery of the system and the instruction manual...................................................................................................... 5

2.2 Guarantee and responsibility....................................................................................................................................... 5

3 Safety and prevention................................................................................................................................................................ 6

3.1 Introduction.................................................................................................................................................................. 6

3.2 Personnel training ....................................................................................................................................................... 6

4 Technical description of the burner ......................................................................................................................................... 7

4.1 Burner designation...................................................................................................................................................... 7

4.2 Models available.......................................................................................................................................................... 7

4.3 Technical data............................................................................................................................................................. 8

4.4 Electrical data.............................................................................................................................................................. 8

4.5 Burner categories - Countries of destination............................................................................................................... 9

4.6 Maximum dimensions.................................................................................................................................................. 9

4.7 Firing rates ................................................................................................................................................................ 10

4.8 Test boiler.................................................................................................................................................................. 11

4.9 Burner equipment...................................................................................................................................................... 11

4.10 Burner description..................................................................................................................................................... 12

4.11 Electrical panel description........................................................................................................................................ 13

4.12 Control box for the air/fuel ratio (LMV52...)............................................................................................................... 14

4.13 Servomotor (SQM48.4....)......................................................................................................................................... 16

5 Installation ................................................................................................................................................................................ 17

5.1 Notes on safety for the installation............................................................................................................................ 17

5.2 Handling.................................................................................................................................................................... 17

5.3 Preliminary checks.................................................................................................................................................... 17

5.4 Operating position..................................................................................................................................................... 18

5.5 Removal of the locking screws from the shutter........................................................................................................ 18

5.6 Preparing the boiler................................................................................................................................................... 18

5.6.1 Boring the boiler plate ............................................................................................................................................... 18

5.6.2 Blast tube length........................................................................................................................................................ 18

5.7 Securing the burner to the boiler............................................................................................................................... 19

5.8 Access to head internal part...................................................................................................................................... 19

5.9 Probe-electrode position ........................................................................................................................................... 19

5.10 Combustion head adjustment.................................................................................................................................... 20

5.11 Gas feeding............................................................................................................................................................... 21

5.11.1 Gas feeding line ........................................................................................................................................................ 21

5.11.2 Gas train.................................................................................................................................................................... 22

5.11.3 Gas train installation.................................................................................................................................................. 22

5.11.4 Gas pressure............................................................................................................................................................. 23

5.12 Electrical wiring ......................................................................................................................................................... 24

5.12.1 Supply cables and external connections passage .................................................................................................... 24

6 Start-up, calibration and operation of the burner ................................................................................................................. 25

6.1 Notes on safety for the first start-up.......................................................................................................................... 25

6.2 Adjustments prior to ignition...................................................................................................................................... 25

6.3 Burner start-up .......................................................................................................................................................... 25

6.4 Burner ignition........................................................................................................................................................... 25

6.5 Combustion air adjustment........................................................................................................................................ 26

20041914 2

Contents

6.5.1 Air adjustment for maximum output ...........................................................................................................................26

6.5.2 Air/fuel adjustment and output modulation system ....................................................................................................26

6.6 Pressure switch adjustment.......................................................................................................................................27

6.6.1 Air pressure switch - check CO..................................................................................................................................27

6.6.2 Maximum gas pressure switch...................................................................................................................................27

6.6.3 Minimum gas pressure switch....................................................................................................................................27

6.6.4 PVP pressure switch kit .............................................................................................................................................27

7 Maintenance ..............................................................................................................................................................................28

7.1 Notes on safety for the maintenance.........................................................................................................................28

7.2 Maintenance programme...........................................................................................................................................28

7.2.1 Maintenance frequency..............................................................................................................................................28

7.2.2 Checking and cleaning...............................................................................................................................................28

7.2.3 Positioning the revolution sensor...............................................................................................................................29

7.3 Opening the burner....................................................................................................................................................30

7.4 Closing the burner......................................................................................................................................................30

8 Faults - Probable causes - Solutions......................................................................................................................................31

A Appendix - Accessories ...........................................................................................................................................................32

B Appendix - Electrical panel layout...........................................................................................................................................34

3 20041914

Declarations

1 Declarations

Declaration of conformity in accordance with ISO / IEC 17050-1

Manufacturer: RIELLO S.p.A.

Address: Via Pilade Riello, 7

37045 Legnago (VR)

Product: Forced draught gas burners

Model: RS 300/EV BLU

RS 400/EV BLU

RS 500/EV BLU

RS 650/EV BLU

RS 800/EV BLU

These products are in compliance with the following Technical Standards:

EN 676

EN 12100

and according to the European Directives:

GAD 2009/142/EC Gas Devices Directive

MD 2006/42/EC Machine Directive

LVD 2014/35/UE Low Voltage Directive

EMC 2014/30/UE Electromagnetic Compatibility

Such products are marked as follows: EC-0085BO0341 RS 300-400/EV BLU

EC-0085BS0382 RS 500/EV BLU

EC-0085BT0337 RS 650/EV BLU

EC-0085BT0337 RS 800/EV BLU

The quality is guaranteed by a quality and management system certified in accordance with UNI EN ISO 9001.

Manufacturer's Declaration

RIELLO S.p.A. declares that the following products comply with the NOx emission limits specified by German standard “1. BIm-

SchV revision 26.01.2010”.

Product Type Model Output

Forced draught gas burners 849T2 RS 300/EV BLU 500 - 3800 kW

850T2 RS 400/EV BLU 800 - 4550 kW

856T2 RS 500/EV BLU 1000 - 5170 kW

1123T2 RS 650/EV BLU 1400 - 6500kW

887T2 RS 800/EV BLU 1200 - 8100 kW

Legnago, 01.12.2015 Executive General Manager

RIELLO S.p.A. - Burner Department Research & Development Director

RIELLO S.p.A. - Burner Department

Mr. U. Ferretti Mr. F. Comencini

20041914 4

Information and general warnings

2.1 Information about the instruction manual

2.1.1 Introduction

The instruction manual supplied with the burner:

is an integral and essential part of the product and must not

be separated from it; it must therefore be kept carefully for

any necessary consultation and must accompany the burner

even if it is transferred to another owner or user, or to

another system. If the manual is lost or damaged, another

copy must be requested from the Technical Assistance Ser-

vice of the area;

is designed for use by qualified personnel;

offers important indications and instructions relating to the

installation safety, start-up, use and maintenance of the

burner.

Symbols used in the manual

In some parts of the manual you will see triangular DANGER

signs. Pay great attention to these, as they indicate a situation of

potential danger.

2.1.2 General dangers

The dangers can be of 3 levels, as indicated below.

2.1.3 Other symbols

Abbreviations used

Ch. Chapter

Fig. Figure

Page Page

Sec. Section

Tab. Table

2 Information and general warnings

DANGER

Maximum danger level!

This symbol indicates operations which, if not car-

ried out correctly, cause serious injury, death or

long-term health risks.

WARNING

This symbol indicates operations which, if not car-

ried out correctly, may cause serious injury, death

or long-term health risks.

CAUTION

This symbol indicates operations which, if not car-

ried out correctly, may cause damage to the ma-

chine and/or injury to people.

DANGER

DANGER: LIVE COMPONENTS

This symbol indicates operations which, if not car-

ried out correctly, lead to electric shocks with le-

thal consequences.

DANGER: FLAMMABLE MATERIAL

This symbol indicates the presence of flammable

materials.

DANGER: BURNING

This symbol indicates the risks of burns due to

high temperatures.

DANGER: CRUSHING OF LIMBS

This symbol indicates the presence of moving

parts: danger of crushing of limbs.

WARNING: MOVING PARTS

This symbol indicates that you must keep limbs

away from moving mechanical parts; danger of

crushing.

DANGER: EXPLOSION

This symbol signals places where an explosive at-

mosphere is present. An explosive atmosphere is

defined as a mixture of dangerous substances

with air, under atmospheric conditions, in the form

of gases, vapours, mist or dust in which, after ig-

nition has occurred, combustion spreads to the

entire unburned mixture.

PERSONAL PROTECTION EQUIPMENT

These symbols indicate the equipment that must

be worn and kept by the operator for protection

against threats against safety and/or health while

at work.

MOUNT CASING

This symbol indicates that it is mandatory to

mount casing again after maintenance, cleaning

or checks.

ENVIRONMENTAL PROTECTION

This symbol gives indications for the use of the

machine with respect for the environment.

IMPORTANT INFORMATION

This symbol indicates important information that

you must bear in mind.

This symbol indicates a list.

5 20041914

Information and general warnings

2.1.4 Delivery of the system and the instruction

manual

When the system is delivered, it is important that:

the instruction manual is delivered to the user by the system

manufacturer, with the recommendation to keep it in the

room where the heat generator is to be installed.

The instruction manual shows:

– the serial number of the burner;

– the address and telephone number of the nearest Assis-

tance Centre.

The system supplier must carefully inform the user about:

– the use of the system;

– any further tests that may be required before activating the

system;

– maintenance, and the need to have the system checked at

least once a year by a representative of the manufacturer

or another specialised technician.

To ensure a periodic check, the manufacturer recom-

mends the drawing up of a Maintenance Contract.

2.2 Guarantee and responsibility

The manufacturer guarantees its new products from the installa-

tion date, in accordance with the regulations in force and/or the

sales contract. At the moment of the first start-up, check that the

burner is integral and complete.

In particular, the rights to the guarantee and the responsibility will

no longer be valid, in the event of damage to things or injury to

people, if such damage/injury was due to any of the following

causes:

incorrect installation, start-up, use and maintenance of the

burner;

improper, incorrect or unreasonable use of the burner;

intervention of unqualified personnel;

carrying out of unauthorised modifications on the equipment;

use of the burner with safety devices that are faulty, incor-

rectly applied and/or not working;

installation of untested supplementary components on the

burner;

powering of the burner with unsuitable fuels;

faults in the fuel supply system;

use of the burner even following an error and/or an irregular-

ity;

repairs and/or overhauls incorrectly carried out;

modification of the combustion chamber with inserts that

prevent the regular development of the structurally estab-

lished flame;

insufficient and inappropriate surveillance and care of those

burner components most likely to be subject to wear and

tear;

the use of non-original components, including spare parts,

kits, accessories and optional;

force majeure.

The manufacturer furthermore declines any and every re-

sponsibility for the failure to observe the contents of this

manual.

.........................................................................................

WARNING

Failure to observe the information given in this

manual, operating negligence, incorrect installa-

tion and carrying out of non authorised modifica-

tions will result in the annulment by the

manufacturer of the guarantee that it supplies with

the burner.

20041914 6

Safety and prevention

3.1 Introduction

The burners have been designed and built in compliance with

current regulations and directives, applying the known technical

rules of safety and envisaging all the potential danger situations.

It is necessary, however, to bear in mind that the imprudent and

clumsy use of the equipment may lead to situations of death risk

for the user or third parties, as well as the damaging of the burner

or other items. Inattention, thoughtlessness and excessive confi-

dence often cause accidents; the same applies to tiredness and

sleepiness.

It is a good idea to remember the following:

The burner must only be used as expressly described. Any

other use should be considered improper and therefore dan-

gerous.

In particular:

it can be applied to boilers operating with water, steam, diather-

mic oil, and to other users expressly named by the manufacturer;

the type and pressure of the fuel, the voltage and frequency of the

electrical power supply, the minimum and maximum deliveries for

which the burner has been regulated, the pressurisation of the

combustion chamber, the dimensions of the combustion cham-

ber and the room temperature must all be within the values indi-

cated in the instruction manual.

Modification of the burner to alter its performance and desti-

nations is not allowed.

The burner must be used in exemplary technical safety con-

ditions. Any disturbances that could compromise safety must

be quickly eliminated.

Opening or tampering with the burner components is not

allowed, apart from the parts requiring maintenance.

Only those parts envisaged by the manufacturer can be

replaced.

3.2 Personnel training

The user is the person, body or company that has acquired the

machine and intends to use it for the specific purpose. He is re-

sponsible for the machine and for the training of the people work-

ing around it.

The user:

undertakes to entrust the machine exclusively to suitably

trained and qualified personnel;

undertakes to inform his personnel in a suitable way about

the application and observance of the safety instructions.

With that aim, he undertakes to ensure that everyone knows

the use and safety instructions for his own duties;

Personnel must observe all the danger and caution indica-

tions shown on the machine.

Personnel must not carry out, on their own initiative, opera-

tions or interventions that are not within their province.

Personnel must inform their superiors of every problem or

dangerous situation that may arise.

The assembly of parts of other makes, or any modifications,

can alter the characteristics of the machine and hence com-

promise operating safety. The manufacturer therefore

declines any and every responsibility for any damage that

may be caused by the use of non-original parts.

In addition:

3 Safety and prevention

WARNING

The manufacturer guarantees safety and proper

functioning only if all burner components are intact

and positioned correctly.

the user must take all the measures neces-

sary to prevent unauthorised people gaining

access to the machine;

the user must inform the manufacturer if

faults or malfunctioning of the accident pre-

vention systems are noticed, along with any

presumed danger situation.

Personnel must always use the personal pro-

tective equipment envisaged by legislation

and follow the indications given in this man-

ual.

7 20041914

Technical description of the burner

4.1 Burner designation

4.2 Models available

Tab. A

4 Technical description of the burner

Designation Voltage Start-up Code

RS 300/EV BLU 3/400/50 Direct/Inverter 3898350

RS 400/EV BLU 3/400/50 Direct/Inverter 3898452

RS 500/EV BLU 3/400/50 Direct/Inverter 3899152

RS 650/EV BLU 3/400/50 Direct/Inverter 20040547

RS 800/EV BLU 3/400/50 Direct/Inverter 3911090

Class 3 EN267 - Class 3 EN676

Range: R

Size

Fuel: Natural gas

Light oil

Light oil / Methane

Adjustment:

Flame control system:

FS1

FS2 Standard (1 stop every 24h)

Continuous operation (1 stop every 72h)

Electrical supply of the system:

3/400/50

3/230/50

Voltage of auxiliaries:

230/50/60

110/50/60

R S 300 EV TC

Emission: C11 or... Class 1 EN267 - EN676

C11 or MZ Class 2 EN267 - EN676

C33 or BLU Class 3 EN267 - EN676

FS1 3/400/50 230/50/60

BASIC DESIGNATION

EXTENDED DESIGNATION

BLU

3N / 400V / 50Hz

3 / 230V / 50Hz

230V / 50-60Hz

110V / 50-60Hz

Heavy oil

E Electronic cam

EV Electronic cam with variable speed (with Inverter)

P Proportional air/gas valve

BP Two stage (light oil) / Proportional valve (gas)

M Mechanical cam

Head: TC Standard head

TL Long head

C11 or...

C13 Class 1 EN267 - Class 3 EN676

20041914 8

Technical description of the burner

4.3 Technical data

Tab. B

(1) Reference conditions: Ambient temperature 20°C - Gas temperature 15°C - Barometric pressure 1013 mbar - Altitude 0 m a.s.l.

(2) Pressure at the test point of the pressure switch (20)(Fig. 4) with zero pressure in the combustion chamber and at maximum burner output.

(3) Sound pressure measured in manufacturer's combustion laboratory, with burner operating on test boiler and at maximum rated output.

4.4 Electrical data

Tab. C

Tab. D

Model RS 300/EV BLU RS 400/EV BLU RS 500/EV BLU RS 650/EV BLU RS 800/EV BLU

Type 849 T2 850 T2 856 T2 1123 T2 887 T2

Output (1)

Output (1) min-max kW 500/1350 ÷ 3800 800/1840 ÷ 4550 1000/2500÷5170 1410/3020÷6500 1200/3500÷8100

Fuels Natural gas: G20 (methane gas) - G21 - G22 - G23 - G25

Gas pressure at max. output

(2) - Gas: G20/G25 mbar 23.3/32.7 34.3/40.2 37.6/56.1 44.8/64.4 45.5/81.2

Operation Continuous / Intermittent

Standard applications Boilers: water, steam, diathermic oil

Ambient temperature °C 0 - 50

Combustion air temperature °C max 60

Noise levels (3)

Sound pressure

Sound power dB(A) 82

-85

-88

-90.1

104.3 88.1

102.5

Burner weight Kg 230 240 250 300 300

Model RS 300/EV BLU RS 400/EV BLU RS 500/EV BLU RS 650/EV BLU RS 800/EV BLU

Main electrical supply

Control circuit power supply 3 ~ 400V +/-10% 50 Hz

1N ~ 230V 50 Hz

Fan motor IE2

rpm

2900

230/400

4.5

15/8.7

2900

400/690

7.5

13.8/8

2900

400/690

9.2

16.9/9.7

2900

400/690

18.5

35.7/20.6

2900

400/690

41.8/24.2

Ignition transformer V1 - V2

I1 - I2 230 V - 1 x 8 kV

1 A - 20 mA

Absorbed electrical power kW max 5.9 9.2 10.8 20.8 24.5

Protection level IP 54

Model RS 400/EV BLU RS 500/EV BLU RS 650/EV BLU RS 800/EV BLU

Main electrical supply

Control circuit power supply 3 ~ 400V +/-10% 50 Hz

1N ~ 230V 50 Hz

Fan motor IE3

rpm

2900

400/690

7.5

13.1/7.6

2930

400/690

9.2

16.5/9.6

2950

400/690

18.5

33/19

2950

400/690

39.4/22.7

Ignition transformer V1 - V2

I1 - I2 230 V - 1 x 8 kV

1 A - 20 mA

Absorbed electrical power kW max 8,8 10,6 20,5 24

Protection level IP 54

This manual suits for next models

Table of contents

Other Riello Burner manuals

Riello

Riello RS 190 Quick start guide

Riello

Riello RS 34 MZ Quick start guide

Riello

Riello 40 G20I Quick start guide

Riello

Riello GAS 4 Quick start guide

Riello

Riello GS5 Quick start guide

Riello

Riello RLS 130/E Quick start guide

Riello

Riello 40 GS3 Quick start guide

Riello

Riello GAS 3 Quick start guide

Riello

Riello 629 T80 Parts list manual

Riello

Riello RN 28 Quick start guide

Riello

Riello RS 28/E Quick start guide

Riello

Riello ER Series Quick start guide

Riello

Riello RC2R Quick start guide

Riello

Riello P 140 T/G Quick start guide

Riello

Riello DB16 LSM C13 Quick start guide

Riello

Riello G120 Quick start guide

Riello

Riello RDB1 WORCESTER GREENSTAR 12/18 Quick start guide

Riello

Riello RLS 200/EVi MX Quick start guide

Riello

Riello RDB2 90 Quick start guide

Riello

Riello RDB3.2 33/44 Quick start guide

Riello

Riello G400 Quick start guide

Riello

Riello RLS 310/EV O2 MX Instruction Manual

Riello

Riello PRESS 3G Quick start guide

Riello

Riello GI/EMME 1400 Quick start guide

Popular Burner manuals by other brands

True Induction

True Induction TI4B user guide

Weishaupt

Weishaupt WG20 Series manual

Carolina Cooker

Carolina Cooker M116672 owner's guide

Unigas

Unigas HTP2000 installation manual

baltur

baltur BT 250 DSG 4T manual

muenkel design

muenkel design round burner Operating and installation instructions

baltur

baltur BT 14 DSGW Instruction

artisan

artisan Art-SB1 Care & use manual

AESYS

AESYS TurboFire II Installation, operation and maintenance manual

IKEA

IKEA GRILLSKÄR manual

baltur

baltur TBL 1000 ME Instruction manual for installation, use and maintenance

Riello Burners

Riello Burners P 200 P/G Installation, use and maintenance instructions

WLD-TEC

WLD-TEC powerjet instruction manual

Bull

Bull 20505CE Assembly instructions

BIO FIRES

BIO FIRES REGULATING BIO CONTAINER 50 Installation & Specifications Manual

baltur

baltur BT 17N Instruction manual for installation, use and maintenance

Ecoflam

Ecoflam Multicalor 170.1 manual

Campingaz

Campingaz Camping Vario Fold manual