Riello Rs 160/ev o2 blu Quick start guide

Installation, use and maintenance instructions

20156417 (4) - 12/2020

Forced draught gas burners

Modulating operation

CODE MODEL TYPE

20158956 RS 160/EV O2BLU 843T2

20172156 RS 160/EV O2BLU 843T2

20172159 RS 200/EV O2BLU 1106T2

20156077 RS 200/EV O2BLU 1106T2

Translation of the original instructions

1 20156417

Contents

1 Declarations................................................................................................................................................................................ 3

2 Information and general warnings............................................................................................................................................ 4

2.1 Information about the instruction manual .................................................................................................................... 4

2.1.1 Introduction.................................................................................................................................................................. 4

2.1.2 General dangers.......................................................................................................................................................... 4

2.1.3 Other symbols ............................................................................................................................................................. 4

2.1.4 Delivery of the system and the instruction manual...................................................................................................... 5

2.2 Guarantee and responsibility....................................................................................................................................... 5

3 Safety and prevention................................................................................................................................................................ 6

3.1 Introduction.................................................................................................................................................................. 6

3.2 Personnel training ....................................................................................................................................................... 6

4 Technical description of the burner ......................................................................................................................................... 7

4.1 Burner designation ...................................................................................................................................................... 7

4.2 Models available.......................................................................................................................................................... 7

4.3 Burner categories ........................................................................................................................................................ 8

4.4 Technical data ............................................................................................................................................................. 8

4.5 Electrical data.............................................................................................................................................................. 8

4.6 Maximum dimensions.................................................................................................................................................. 9

4.7 Burner equipment........................................................................................................................................................ 9

4.8 Firing rates ................................................................................................................................................................ 10

4.9 Test boiler.................................................................................................................................................................. 10

4.9.1 Firing rate on basis of air density .............................................................................................................................. 11

4.10 Burner description ..................................................................................................................................................... 12

4.11 Control box for the air/fuel ratio (LMV52...) ............................................................................................................... 13

4.12 Servomotor................................................................................................................................................................ 15

4.13 PLL52... module (Optional) ....................................................................................................................................... 16

4.13.1 Terminal ratings, cable lengths and cross-sectional areas ....................................................................................... 16

4.14 Oxygen sensor QGO20 ... (optional)........................................................................................................................ 17

4.14.1 Technical data QGO20.............................................................................................................................................. 18

5 Installation ................................................................................................................................................................................ 19

5.1 Notes on safety for the installation ............................................................................................................................ 19

5.2 Handling .................................................................................................................................................................... 19

5.3 Preliminary checks .................................................................................................................................................... 19

5.4 Operating position ..................................................................................................................................................... 20

5.5 Preparing the boiler ................................................................................................................................................... 20

5.5.1 Introduction................................................................................................................................................................ 20

5.5.2 Boring the boiler plate ............................................................................................................................................... 20

5.5.3 Blast tube length........................................................................................................................................................ 21

5.6 Positioning probe - electrode..................................................................................................................................... 21

5.7 Securing the burner to the boiler............................................................................................................................... 22

5.8 Combustion head adjustment.................................................................................................................................... 23

5.9 Burner closing ........................................................................................................................................................... 24

5.10 Gas feeding ............................................................................................................................................................... 25

5.10.1 Gas feeding line ........................................................................................................................................................ 25

5.10.2 Gas train.................................................................................................................................................................... 26

5.10.3 Gas train installation.................................................................................................................................................. 26

5.10.4 Gas pressure............................................................................................................................................................. 27

5.11 Electrical wiring ......................................................................................................................................................... 28

5.11.1 Supply cables and external connections passage .................................................................................................... 28

5.11.2 Motor cable shield ..................................................................................................................................................... 29

5.11.3 Speed sensor adjustment.......................................................................................................................................... 29

5.11.4 Positioning the rpm sensor........................................................................................................................................ 29

5.11.5 Inverter connection.................................................................................................................................................... 29

6 Start-up, calibration and operation of the burner ................................................................................................................. 30

6.1 Notes on safety for the first start-up .......................................................................................................................... 30

6.2 Adjustments prior to ignition ...................................................................................................................................... 30

6.3 Burner start-up .......................................................................................................................................................... 31

20156417 2

Contents

6.4 Burner adjustment......................................................................................................................................................31

6.4.1 Firing output ...............................................................................................................................................................31

6.4.2 Maximum output ........................................................................................................................................................31

6.4.3 Minimum output .........................................................................................................................................................31

6.5 Final calibration of the pressure switches ..................................................................................................................32

6.5.1 Air pressure switch.....................................................................................................................................................32

6.5.2 Maximum gas pressure switch...................................................................................................................................32

6.5.3 Minimum gas pressure switch....................................................................................................................................33

6.5.4 PVP pressure switch kit .............................................................................................................................................33

6.6 Steady-state operation...............................................................................................................................................33

6.7 Ignition failure.............................................................................................................................................................33

6.8 Burner flame goes out during operation.....................................................................................................................33

6.9 Stopping of the burner ...............................................................................................................................................34

6.10 Final checks (with burner operating)..........................................................................................................................34

6.11 Description of O2 trim control (optional) ...................................................................................................................35

6.11.1 Operating principle of O2 trim control ........................................................................................................................35

7 Maintenance ..............................................................................................................................................................................36

7.1 Notes on safety for the maintenance .........................................................................................................................36

7.2 Maintenance programme ...........................................................................................................................................36

7.2.1 Maintenance frequency..............................................................................................................................................36

7.2.2 Safety test - with gas feeding closed .........................................................................................................................36

7.2.3 Checking and cleaning...............................................................................................................................................36

7.2.4 Measuring the ionisation current................................................................................................................................37

7.2.5 Checking the air and gas pressure on the combustion head .....................................................................................37

7.2.6 Safety components ....................................................................................................................................................37

7.3 Opening the burner ....................................................................................................................................................38

7.4 Closing the burner......................................................................................................................................................38

A Appendix - Accessories ...........................................................................................................................................................39

B Appendix - Electrical panel layout...........................................................................................................................................41

3 20156417

Declarations

1 Declarations

Declaration of conformity in accordance with ISO / IEC 17050-1

Manufacturer: RIELLO S.p.A.

Address: Via Pilade Riello, 7

37045 Legnago (VR)

Product: Forced draught gas burners

Model and type: RS 160/EV O2BLU

RS 200/EV O2BLU

843T2

1106T2

These products are in compliance with the following Technical Standards:

EN 676

EN 12100

and according to the European Directives:

GAR 2016/426/EU Gas Devices Regulation

MD 2006/42/CE Machine Directive

LVD 2014/35/EU Low Voltage Directive

EMC 2014/30/EU Electromagnetic Compatibility

Such products are marked as follows:

The quality is guaranteed by a quality and management system certified in accordance with ISO 9001:2015.

Legnago, 21.04.2018 Executive General Manager

RIELLO S.p.A. - Burner Department

Research & Development Director

RIELLO S.p.A. - Burner Department

Mr. U. Ferretti Mr. F. Comencini

CE-0085BS0266 RS 160/EV O2BLU

CE-0085BT0419 RS 200/EV O2 BLU

20156417 4

Information and general warnings

2.1 Information about the instruction manual

2.1.1 Introduction

The instruction manual supplied with the burner:

is an integral and essential part of the product and must not

be separated from it; it must therefore be kept carefully for

any necessary consultation and must accompany the burner

even if it is transferred to another owner or user, or to

another system. If the manual is lost or damaged, another

copy must be requested from the Technical Assistance Ser-

vice of the area;

is designed for use by qualified personnel;

offers important indications and instructions relating to the

installation safety, start-up, use and maintenance of the

burner.

Symbols used in the manual

In some parts of the manual you will see triangular DANGER

signs. Pay great attention to these, as they indicate a situation of

potential danger.

2.1.2 General dangers

The dangers can be of 3 levels, as indicated below.

2.1.3 Other symbols

Abbreviations used

Ch. Chapter

Fig. Figure

Page Page

Sec. Section

Ta b . Ta b l e

2 Information and general warnings

DANGER

Maximum danger level!

This symbol indicates operations which, if not car-

ried out correctly, cause serious injury, death or

long-term health risks.

WARNING

This symbol indicates operations which, if not car-

ried out correctly, may cause serious injury, death

or long-term health risks.

CAUTION

This symbol indicates operations which, if not car-

ried out correctly, may cause damage to the ma-

chine and/or injury to people.

DANGER

DANGER: LIVE COMPONENTS

This symbol indicates operations which, if not car-

ried out correctly, lead to electric shocks with le-

thal consequences.

DANGER: FLAMMABLE MATERIAL

This symbol indicates the presence of flammable

materials.

DANGER: BURNING

This symbol indicates the risks of burns due to

high temperatures.

DANGER: CRUSHING OF LIMBS

This symbol indicates the presence of moving

parts: danger of crushing of limbs.

WARNING: MOVING PARTS

This symbol indicates that you must keep limbs

away from moving mechanical parts; danger of

crushing.

DANGER: EXPLOSION

This symbol signals places where an explosive at-

mosphere may be present. An explosive atmos-

phere is defined as a mixture - under atmospheric

conditions - of air and flammable substances in

the form of gases, vapours, mist or dust in which,

after ignition has occurred, combustion spreads to

the entire unburned mixture.

PERSONAL PROTECTION EQUIPMENT

These symbols indicate the equipment that must

be worn and kept by the operator for protection

against threats against safety and/or health while

at work.

OBLIGATION TO ASSEMBLE THE HOOD AND

ALL THE SAFETY AND PROTECTION DEVIC-

This symbol signals the obligation to reassemble

the hood and all the safety and protection devices

of the burner after any maintenance, cleaning or

checking operations.

ENVIRONMENTAL PROTECTION

This symbol gives indications for the use of the

machine with respect for the environment.

IMPORTANT INFORMATION

This symbol indicates important information that

you must bear in mind.

This symbol indicates a list.

5 20156417

Information and general warnings

2.1.4 Delivery of the system and the instruction

manual

When the system is delivered, it is important that:

the instruction manual is delivered to the user by the system

manufacturer, with the recommendation to keep it in the

room where the heat generator is to be installed.

The instruction manual shows:

– the serial number of the burner;

– the address and telephone number of the nearest Assis-

tance Centre.

The system supplier must carefully inform the user about:

– the use of the system;

– any further tests that may be required before activating the

system;

– maintenance, and the need to have the system checked at

least once a year by a representative of the manufacturer

or another specialised technician.

To ensure a periodic check, the manufacturer recom-

mends the drawing up of a Maintenance Contract.

2.2 Guarantee and responsibility

The manufacturer guarantees its new products from the installa-

tion date, in accordance with the regulations in force and/or the

sales contract. At the moment of the first start-up, check that the

burner is integral and complete.

In particular, the rights to the guarantee and the responsibility will

no longer be valid, in the event of damage to things or injury to

people, if such damage/injury was due to any of the following

causes:

incorrect installation, start-up, use and maintenance of the

burner;

improper, incorrect or unreasonable use of the burner;

intervention of unqualified personnel;

carrying out of unauthorised modifications on the equipment;

use of the burner with safety devices that are faulty, incor-

rectly applied and/or not working;

installation of untested supplementary components on the

burner;

powering of the burner with unsuitable fuels;

faults in the fuel supply system;

use of the burner even following an error and/or an irregular-

ity;

repairs and/or overhauls incorrectly carried out;

modification of the combustion chamber with inserts that

prevent the regular development of the structurally estab-

lished flame;

insufficient and inappropriate surveillance and care of those

burner components most likely to be subject to wear and

tear;

the use of non-original components, including spare parts,

kits, accessories and optional;

force majeure.

The manufacturer furthermore declines any and every re-

sponsibility for the failure to observe the contents of this

manual.

.........................................................................................

WARNING

Failure to observe the information given in this

manual, operating negligence, incorrect installa-

tion and carrying out of non authorised modifica-

tions will result in the annulment by the

manufacturer of the guarantee that it supplies with

the burner.

20156417 6

Safety and prevention

3.1 Introduction

The burners have been designed and built in compliance with

current regulations and directives, applying the known technical

rules of safety and envisaging all the potential danger situations.

It is necessary, however, to bear in mind that the imprudent and

clumsy use of the equipment may lead to situations of death risk

for the user or third parties, as well as the damaging of the burner

or other items. Inattention, thoughtlessness and excessive confi-

dence often cause accidents; the same applies to tiredness and

sleepiness.

It is a good idea to remember the following:

The burner must only be used as expressly described. Any

other use should be considered improper and therefore dan-

gerous.

In particular:

it can be applied to boilers operating with water, steam, diather-

mic oil, and to other users expressly named by the manufacturer;

the type and pressure of the fuel, the voltage and frequency of the

electrical power supply, the minimum and maximum deliveries for

which the burner has been regulated, the pressurisation of the

combustion chamber, the dimensions of the combustion chamber

and the room temperature must all be within the values indicated

in the instruction manual.

Modification of the burner to alter its performance and desti-

nations is not allowed.

The burner must be used in exemplary technical safety con-

ditions. Any disturbances that could compromise safety must

be quickly eliminated.

Opening or tampering with the burner components is not

allowed, apart from the parts requiring maintenance.

Only those parts envisaged by the manufacturer can be

replaced.

3.2 Personnel training

The user is the person, body or company that has acquired the

machine and intends to use it for the specific purpose. He is re-

sponsible for the machine and for the training of the people work-

ing around it.

The user:

undertakes to entrust the machine exclusively to suitably

trained and qualified personnel;

undertakes to inform his personnel in a suitable way about

the application and observance of the safety instructions.

With that aim, he undertakes to ensure that everyone knows

the use and safety instructions for his own duties;

Personnel must observe all the danger and caution indica-

tions shown on the machine.

Personnel must not carry out, on their own initiative, opera-

tions or interventions that are not within their province.

Personnel must inform their superiors of every problem or

dangerous situation that may arise.

The assembly of parts of other makes, or any modifications,

can alter the characteristics of the machine and hence com-

promise operating safety. The manufacturer therefore

declines any and every responsibility for any damage that

may be caused by the use of non-original parts.

In addition:

3 Safety and prevention

WARNING

The manufacturer guarantees safety and proper

functioning only if all burner components are intact

and positioned correctly.

the user must take all the measures neces-

sary to prevent unauthorised people gaining

access to the machine

the user must inform the manufacturer if

faults or malfunctioning of the accident pre-

vention systems are noticed, along with any

presumed danger situation

personnel must always use the personal pro-

tective equipment envisaged by legislation

and follow the indications given in this man-

ual

7 20156417

Technical description of the burner

4.1 Burner designation

4.2 Models available

Tab. A

4 Technical description of the burner

R S 160 EV O2TC FS1 3/400-230/50 230/50/60

BASIC DESIGNATION

EXTENDED DESIGNATION

BLU

Range : R

Size

Fuel : Natural gas

Light oil

Light oil / Natural gas

Adjustment :

Flame control system :

FS1

FS2

Standard (1 stop every 24h)

Continuous operation (1 stop every 72h)

Electrical supply of the system :

3/400/50

3/230/50

Voltage of auxiliaries :

230/50/60

110/50/60

3N / 400V / 50Hz

3 / 230V / 50Hz

230V / 50-60Hz

110V / 50-60Hz

Heavy oil

E Electronic cam

EV Electronic cam and variable speed (with Inverter)

M Mechanical cam

P Proportional air/gas valve

Head : TC Standard head

TL Long head

Emission : C01 or ...

BLU

Class 1 EN676

Class 2 EN676

Class 3 EN676

3/400-230/50 3N / 400V-230V / 50Hz

E O2Electronic cam and suitable for Oxygen Control (O2)

EV O2Electronic cam and variable speed (with Inverter) and suitable for Oxygen Control O2

Designation Voltage Start-up Code

RS 160/EV O2BLU TC 3~ 400V - 50Hz Diretto/inverter 20158956

RS 160/EV O2BLU TL 3~ 400V - 50Hz Diretto/inverter 20172156

RS 200/EV O2BLU TC 3~ 400V - 50Hz Diretto/inverter 20172159

RS 200/EV O2BLU TL 3~ 400V - 50Hz Diretto/inverter 20156077

20156417 8

Technical description of the burner

4.3 Burner categories

Tab. B

4.4 Technical data

Tab. C

(1) Reference conditions: Room temperature 20°C - Gas temperature 15°C - Barometric pressure 1013 mbar - Altitude 0 m above sea level.

(2) Pressure on the pressure switch socket (Fig. 29 at page 30) with zero pressure in the combustion chamber and at maximum burner output.

(3) Sound pressure measured in manufacturer's combustion laboratory, with burner operating on test boiler and at maximum rated output. The sound

power is measured with the “Free Field” method, as per EN 15036, and according to an “Accuracy: Category 3” measuring accuracy, as set out in

EN ISO 3746.

(4) Blast tube: short-long.

4.5 Electrical data

Tab. D

Country of destination Gas category

CY, MT I3B/P

LU,PL I2E, II2E3B/P

BE I2E(R), I3

NL I2EK, II2EK3B/P

DE I2ELL, II2ELL3B/P

FR I2Er, II2Er3P

AT-BG-CH-CZ-DK-EE-ES-FI-GB-GR-HU-IE-IS-IT-LT-LV-NO

PT- RO-SE-SI-SK-TR I2H, II2H3B/P, II2H3P

Model RS 160/EV O2BLU RS 200/EV O2BLU

Output (1) Max. kW

Mcal/h

930 ÷ 1860

800 ÷ 1600

1380 ÷ 2400

1187 ÷ 2064

Min. kW

Mcal/h

300

258

550

473

Combustibile Natural gas: G20 (methane gas) G21 - G22 - G23 - G25 - G31

Pressione gas alla potenza max. (2)

- Gas: G20 / G25

- Gas: G31

mbar 17.7 / 26.4

19.6

28.0 / 41.8

19.6

Fuel – Intermittent (min. 1 stop in 24 hours)

– Modulating with the kit (see ACCESSORIES)

Standard applications Boilers: water. steam. diathermic oil

Ambient temperature °C 0 - 40

Combustion air temperature °C max 60

Noise levels (3) Sound pressure

Sound power dB(A) 80,5

91,5

83,0

94,0

Weight (4) kg 96 - 98 101 - 103

Model RS 160/EV O2BLU RS 200/EV O2BLU

Main electrical supply

Control circuit power supply

3~ 400V +/-10% 50Hz

1N~ 230V +/-10% 50Hz

Fan motor IE3 Hz

rpm

2895

230 - 400

4.5

15 - 8.7

2935

230 - 400

5.5

17.7 - 10.2

Ignition transformer V1 - V2

I1 - I2

230 V - 1 x 8 kV

1 A - 20 mA

Absorbed electrical power kW max 5.4 6.5

Protection level IP 44

This manual suits for next models

Table of contents

Other Riello Burner manuals

Riello

Riello RIELLO 40 F20 1/230/50 Quick start guide

Riello

Riello RS 34/E MZ Quick start guide

Riello

Riello 521T80 Quick start guide

Riello

Riello RLS Series Quick start guide

Riello

Riello 40 F10 Quick start guide

Riello

Riello DB 4 SE FGR Quick start guide

Riello

Riello RS 28/M Quick start guide

Riello

Riello RBS 200 2S User manual

Riello

Riello GAS 3 Quick start guide

Riello

Riello RS 200/M BLU Quick start guide

Riello

Riello RS 68/EV O2 BLU Quick start guide

Riello

Riello 40 FS5 Quick start guide

Riello

Riello RS 300/E BLU Quick start guide

Riello

Riello RS 70/M Quick start guide

Riello

Riello 20074125 Quick start guide

Riello

Riello P 140 T/G Quick start guide

Riello

Riello G20 Quick start guide

Riello

Riello RS 810/EV BLU Quick start guide

Riello

Riello RLS 300/BP MX Quick start guide

Riello

Riello 901 T Quick start guide

Riello

Riello RS 310/EV ULX Quick start guide

Riello

Riello RX35 S/PV H Quick start guide

Riello

Riello RLS 68/M MX FS1 Quick start guide

Riello

Riello RS 160/M BLU Quick start guide

Popular Burner manuals by other brands

True Induction

True Induction TI4B user guide

Weishaupt

Weishaupt WG20 Series manual

Carolina Cooker

Carolina Cooker M116672 owner's guide

Unigas

Unigas HTP2000 installation manual

baltur

baltur BT 250 DSG 4T manual

muenkel design

muenkel design round burner Operating and installation instructions

baltur

baltur BT 14 DSGW Instruction

artisan

artisan Art-SB1 Care & use manual

AESYS

AESYS TurboFire II Installation, operation and maintenance manual

IKEA

IKEA GRILLSKÄR manual

baltur

baltur TBL 1000 ME Instruction manual for installation, use and maintenance

Riello Burners

Riello Burners P 200 P/G Installation, use and maintenance instructions

WLD-TEC

WLD-TEC powerjet instruction manual

Bull

Bull 20505CE Assembly instructions

BIO FIRES

BIO FIRES REGULATING BIO CONTAINER 50 Installation & Specifications Manual

baltur

baltur BT 17N Instruction manual for installation, use and maintenance

Ecoflam

Ecoflam Multicalor 170.1 manual

Campingaz

Campingaz Camping Vario Fold manual

Riello RS 160/EV O2 BLU Quick start guide

Popular Burner manuals by other brands