Rife DM7 Parts list manual

Rife Technologies
HEIGHT-ADJUSTABLE DESK DM7
www.rifeindia.com
Tel : [phone]

Part
Name
Qty
1
End Frame
4
2
Cross Rails
2
3
Side Bracket
2
4
Lift Column
2
5
Foot
2
6
Control Box
1
7
Handset
1
8
Power Cord
1
9
Leveling Feet
4
10
Machine Screws
M6*12
24
11
Machine Screws
M6*10
8
12
Wood Screws
M5*16
14
13
Cable Clips
8

Attach the foot (Part 5) to the
bottom of each Lift Column (Part
4) using 4 pcs M6 × 12 mm
Machine Screws
（Part 10）
tighten
firmly.
Attach the Leveling Feet（Part 9）
to the foot foot (Part 5) and
tighten firmly.
Insert the Cross Rails (Part 2) into the End Frame (Part 1) on
both sides.

Ensure the wood screws are not too long for the width of your
desktop surface; Otherwise they may puncture it when screwed
all the way in!
Check that the frame is properly positioned on the underside of
the desktop.
Attached the base to the underside of the desktop using 14
M5x16mm Wood Screws
3 per Side Bracket ( Part 3 ) ---6 total
1 per End Frame ( Part 1) ---4 total
2 per Handset ( Part 7 )--- 2 total
2 per Control Box ( Part 6 )--- 2 total

1.The interface of hand controller
The key instructions:
2.Initialization Operation
When the system is abnormal, or hand controller display the "RST", you need to
make lift table initialized, initialization, Press the "DOWN" button, until the motor
stopped then after 5 second, enter the initialization mode automatically.At this time
can't loosen the "DOWN" button, if loosen "DOWN" button system initialization
stop .When Initialization is complete, the buzzer will prompt, said initial success.
3.Up Down Operation
When press the "UP" button, the desktop upward run, until reach the highest point
of the desktop.
When press "DOWN" button, desktop run DOWN, until you reach the lowest
desktop.
When short press "UP" or "DOWN" button, desktop to run a small distance,
corresponding implementation point move.
4.Store Position and Memory run
The hand controller can store to 4 points, the storage method is as follows, when
running to a specific point, press "SET" button, the digital tube display "S -", "-" flash
at the same time, press "1-4" at this time, storage location to the corresponding
label at this time.
If you want to run memory Position at this time only need to click on the
corresponding storage location of the label, the digital tube will display
corresponding to the height of the label position, the corresponding height position
then automatically run to the store, run time, any key to stop the system.

5.The minimum limit set
System supports desktop minimum height limit, methods for operation, when it
comes to setting the lowest height for the desktop height, the corresponding height
at the same time Press the "SET" and "DOWN" button for 5 seconds, the buzzer
sound can be heard at this time, is the location of the minimum storage success.
Cancel storage minimum height limit method 1: initialize the system, system low
cancelled.Method 2: allow the desktop to run low, at the same time Press the "SET"
and "DOWN" button for 5 seconds will hear the buzzer sounds at this time, said the
lowest position to cancel the success.
6.The maximum limit set
System supports desktop maximum height limit, methods for operation, when it
comes to setting the highest height for the desktop height, the corresponding
height at the same time Press the "SET" and "UP" button for 5 seconds, the buzzer
sound can be heard at this time, is the location of the maximum storage success.
Cancel storage maximum height limit method 1: initialize the system, system high
cancelled.Method 2: allow the desktop to run high, at the same time Press the "SET"
and "UP" button for 5 seconds will hear the buzzer sounds at this time, said the
lowest position to cancel the success.
7.Lock and Unlock the desktop
Lock: at the same time press the "UP" + "DOWN" for 5 seconds, when hearing the
buzzer sounds at this time the digital tube display "-", said the system has been
locked, can't make a lift to the system operation.
Unlock: at the same time Press the "UP" and "DOWN" for 5 seconds, when hearing
the buzzer sounds at this time the digital tube from the "-" shows to the normal
digital display, the said system has been unlocked.