Rife DML1000 User manual

21Rife Technologies
www.rifeindia.com
Tel : [phone]
PART LISTA- Column x 2 B - Connection Tube x 2
C - Supporting Tube x 1 D- Foot x 2
E - Left Side Bracket x 1 F - Right Side Bracket 1x 1
G - L Connector x 2 HH -- Connecting Board x 4
HEIGHT-ADJUSTABLE DESK
DML1000

43J - Power Supply x 1
K - Power Supply Cable x 1 L - Cable x 1
M - Power Cord x 1 N - Cable clip x 8
O- M6x12 Screw x 24
I-Control Box x 1
P- M6x14 Screw x 16
R-ST5x16 screw x 12
S-Acrylic adhesive Tape x 4T- Wooden pin x 6
U -4 mm Allen Key x 1 V-Table board
Q- ST3.8x20 screw x 2

6
5
Step 1
Checklist
A- Column x 2
B - Connection Tube x 2
O- M6x12 Screw x 8
U -4 mm Allen Key x 1
Step2
D- Foot x 2
U -4 mm Allen Key x 1
O- M6x12 Screw x 8
Step 3
C - Supporting Tube x 1
UU -4 mm Allen Key x 1
1
O- M6x12 Screw x 4
Step 4
G - L Connector x 2
U -4 mm Allen Key x 1x
O- M6x12 Screw x4
Checklist
Checklist Checklist

8
7
Step 5
Checklist
E - Left Side Bracket x 1 1
F - Right Side Bracket x 1 1
U -4 mm Allen Key x 1 1
O- M6x12 Screw x 4
Step 6
Checklist
V- Table board
U -4 mm Allen Key x 1 1
Step 7
Checklist
R-ST5x16 screw x 12
Q- ST3.8x20 screw x 2
Step 8
J - Power Supply x 1 S- Acrylic adhesive Tape x 4
Checklist
H -- Connecting Board x 4
T- Wooden pin x 6
P- M6x14 Screw x 16

10
9
Step 9
Up & Down Movement: Press the UP arrow continuously, the legs will move upPress the DOWN arrow continuously, the legs will move down
Release arrows to stop movement.Memory Preset Positions:Use the UP and DOWN arrows to set table at a desired height. Press the POSITION SETTING BUTTON (M) followed by one of the 3PRESET POSITION BUTTONS(1 2 3) buttons. The memory position is set.There are up to 3 presets available. To return to a memory preset press the desired number.Reset:Press the DOWN button and lower the desk to its lowest setting.. Press the DOWN Button again for ~ 5 seconds until the LED reads “RST” Press the DOWN button & hold it while the legs move up & down to level and stop. Release the DOWN button as the reset is now complete and your table is ready to use.Child lockPress the up arrow and down arrow at the same time for 5 seconds, and then release the sound when the control box makes a “Bi--” sound. The handset displays “---” and the table enter the Child lock mode.UnlockPress the up arrow and down arrow at the same time for 5 seconds, and then release the sound when the control box makes a “Bi--” sound. The handset displays the number and the table exit the lock mode.USE INSTRUCTIONSChecklist
K - Power Supply Cable x 1 L - Cable x 1
M - Power Cord x 1 N - Cable clip x 8

12
11 Error Code KeyCodeMeaningSuggested ActionsE01 Power supply TroublesChange the Control box
E03Unbalance more than 10mmReset the deskE04Unconnected to the handsetPlug into the control boxE05Anti-collision stopRelease then use againE06Main power damageChange the Control box
E07Active power protectionRe-plug the powerE08Unbalance of the desktopReset the deskE09OverheatedLet the desk cool down for 20minutesE11/21Unconnected with motor M1/M2Check the cables connectionE12/22Communication error M1/M2Change the control boxE13/23Motor power cable connection issue M1/M2Replace the motor or control boxE14/24Motor sensor errorM1/M2Change the MotorE15/25Motor damage M1/M2Change the MotorE16/26Motor blocked M1/M2Reset the deskE17/27Motor errorM1/M2Change the MotorE18/28OverloadedReduce weight on the desk