Rifton K710 User manual

Support Station
K710 Product Manual
K710 Product Manual

2© 2018 Rifton Equipment
Contents
Important information 2
Safety messages 3
Recommended use 4
Item dimensions 5
Check your order 6
Installation 6
Basic components 7
Accessories 8
Operation 9
Maintenance, cleaning and warranty 10
Materials and user modifications 11
IMPORTANT
Please save this product manual for future reference. Additional copies are
available at http://www.rifton.com/customer-service/product-manuals.
Key for users
Use this key to determine which sections of this product manual apply to you.
Technical Users For professionals who order and set up Rifton products.
Home Users For care-givers who use Rifton products on a regular basis.
Maintenance Personnel For anyone who is responsible for service or
re-ordering of Rifton products and parts.

3
• Thoroughly read and understand the information in this product manual before
attempting to use this product. If the procedures and instructions in this product manual
are not followed, serious injury or death could occur.
• A qualified professional must assess the appropriateness and safety of all equipment for
each user.
• This product is intended for use by clients of unreliable judgment. Adult supervision is
required at all times.
• To prevent falls and injuries:
○Ensure the appropriate use of straps and supports at all times. Straps and supports
are provided for the safety of the user and must be carefully adjusted for comfort and
security.
○Tighten all adjustment knobs before use and immediately after making any
adjustments.
○Do not adjust the height of the trunk board while in use.
○Do not use this product for clients outside the height and weight limits specified in
this manual.
○Do not use the pivot feature when the client is unable to move his or her feet.
○Only use the pivot feature when the trunk board is horizontal.
• To prevent structural failure, which may result in serious injury or death:
○Inspect this product and accessories regularly for loose or missing screws, metal
fatigue, cracks, broken welds, missing attachments, general instability or other signs
of excessive wear.
○Immediately remove this product from use when any condition develops that might
make operation unsafe.
○Do not use Rifton components or products for any purpose other than their intended
use.
WARNING

4
Figure 4a: The fixed configuration can
be used as a stand-alone unit with the
kneeboard and padded trunk board. It
enables a client to assist in sit-to-stand
for clothing adjustment and hygiene care.
The client may remain in the assisted
upright position for a diaper change or
may return to a sitting position on a rolling
commode or shower chair. When using the
kneeboard, the trunk board cannot pivot.
Figure 4b: The pivot configuration can
be used as a transfer aid to a stationary
toilet. Without the kneeboard, the padded
trunk board can pivot 180º. Installed near
a standard toilet, a client can use the
Support Station to assist in sit-to-stand
from a wheelchair and rest their torso
on the padded trunk board. Then, while
moving their feet, a client can be pivoted to
a position close to the toilet.
Recommended use
The Rifton Support Station is a Class 1 medical device. It provides front-leaning support
during toileting and hygiene care for children and adults with disabilities. When not in use,
it folds neatly against the wall.
Figure 4a
Figure 4b

5
User and item dimensions
Basic dimensions: in use, and folded up with kneeboard.
User dimensions– inches (cm)
Height 46-80 (117-203)
Important: User height and weight
must not exceed the maximum.
Item dimensions – inches (cm)
Trunk board size 24x 24 (61x61)
Maximum trunk board height 45 (114)
Minimum trunk board height 26 (66)
Max. working load lbs (kg) 250 (113)
Suggested layout for installation when used with pivot design.
31" 8" 27-1/2"
65-1/2"
26" minimum 4-1/2"
31"
26"minimum
8" 27 ½"
65 ½"
4 ½"
180° Pivoting range
12" - 15" recommended
20-1/2"
32"
30"
20-1/2"
30-1/2"
20 ½"
30"
32"
12"–15"recommended
180° pivoting range
20½"
30½"

6
Check your order
The Rifton Support Station comes fully assembled. Do not dispose of packaging materials
until you are completely satisfied that the product is installed properly and working.
If your shipment is incomplete or in any way damaged on arrival, please call
Customer Service, 800.571.8198.
Installation
To prevent falls and
serious injury:
• Make sure the bottom ends of the
vertical extrusions rest weight-bearing
on the floor.
• A qualified professional, such as a
building contractor or maintenance
person, must securely install this
product to the wall using the following
procedure:
1. Figure 6a: Remove one end cap from
each horizontal crosspiece of the frame
with a flat-head screwdriver. Slide
out the cover strips to access the bolt
holes. Fasteners are not included. Use
fasteners to suit the wall construction.
Installation must be adequate to support
a 250 lb.(113 kg) user.
2. Fasten product securely to the wall
with a minimum of two fasteners per
horizontal crosspiece.
3. Replace the cover strips and end caps.
4. Frame must be level and perpendicular
to the floor so that the height adjusters
move and latch smoothly.
5. If height adjusters do not operate
satisfactorily, contact Customer Service.
WARNING
Figure 6a

7
To prevent falls or
injury, do not adjust
the height or angle of the trunk board
with a client on it.
The Rifton Support Station is equipped with
two adjustment bars:
•
Figure 7a: The lower adjustment bar
sets the height of the trunk board (A).
•
Figure 7a: The upper adjustment bar
sets the angle of the trunk board (B).
•
Figure 7b: The adjustment bars can
be worked from either side. Grasp the
handle (C) from one side only, lift the
handle, and squeeze the trigger (D)
while using your other hand to lift on the
front edge of the trunk board as shown
in figure 7a. The built-in safety stop will
prevent you from squeezing the trigger
while the trunk board is bearing weight.
• Move the adjustment bar to the desired
position and release the trigger, allowing
the trigger to engage into the nearest
position.
•
Figure 7b: The height of the trunk board
from the floor is indicated on the inside
of the frame (E), referenced from the top
edge of the lower adjustment bar.
• The trunk board may be folded against
the wall while not in use. To do this, set
the lower adjustment bar to less than
37", then raise the upper adjustment bar
to its maximum. If the kneeboard is not
attached, make sure the pivot latch is
rotated to center before collapsing the
trunk board.
Figure 7a
A
A
B
B
Figure 7b
C
C
D
D
E
E
Basic item
WARNING

8
Figure 8a
Figure 8b
Pivot Configuration
Figure 8a: The trunk board can rotate to
facilitate transfers to a stationary toilet.
This feature does not function with the
kneeboard attached. The trunk board must
be horizontal before using the pivoting
feature.
Figure 8a: The rotation of the trunk board
can be set in 15˚ increments using the pivot
latch. Press down on the pivot latch handle
(A) firmly while rotating the trunk board.
Release the latch and allow it to engage
into the nearest position. The trunk board
can be rotated 180 degrees.
Removal of kneeboard
Figure 8b: To remove the kneeboard,
pull out the four quick-release pins (B)
underneath the trunk board. To install the
kneeboard, line up the braces and insert
the pins.
Accessories
Handholds
Figure 8c: The handholds can be secured
in the slots of the trunk board for users
who require a vertical hold. To attach the
handhold, remove the nut from the bottom
and assemble it again through the slot in
the trunk board.
Support strap
To avoid falls or injury,
adult supervision is
required at all times. The support strap
is not a substitute for close caregiver
supervision.
Figures 8d and 8c: The support strap (C)
can be secured around the user’s trunk to
help maintain position on the trunk board. To
attach the strap on the trunk board, fasten
the short straps (D) around the edge of the
trunk board and through the hand slot.
B
B
A
A
Figure 8c
Figure 8d
Figure 8e
C
C
D
D
WARNING

9
Figure 9a. The user approaching the trunk board
and reaching out for the handholds.
Figure 9b. The user in the raised position.
Operation
• Adjust the trunk board to the
appropriate height and angle for the
user. The recommended height is just
below the hips of the user.
•
Figure 9a: Wheel the client to the
Support Station facing the padded
concave trunk board.
• With the handholds or slots the user
can assist, pulling up or forward, or can
be helped up onto the trunk board to
support the upper body.
• Secure the support strap if needed (see
Page 8).
• The cutouts on the sides of the trunk
board may be used for additional
support for the elbows.
• While the user is positioned securely
on the trunk board, the caregiver can
complete necessary care and clothing
adjustments.
Fixed configuration
Figure 9b: When the user is securely
positioned with the upper body supported
by the trunk board, the wheelchair can be
removed and replaced by a portable toilet.
Pivot configuration
Securely position client on the trunk board.
Pivot the user and trunk board to enable
access to the fixed toilet. The client must
have enough leg control to move their feet
during pivot.

10
Maintenance
This product is designed and tested for an expected life of 5 years when used and
maintained in accordance with this manual. At all times, users must ensure that the
product remains in a safe and useable condition, including regular maintenance and
inspections as specified in the manual.
To prevent structural failure, which may result in serious injury or death:
• Inspect this product and accessories regularly for loose or missing screws, metal
fatigue, cracks, broken welds, missing attachments, general instability or other signs of
excessive wear.
• Immediately remove this product from use when any condition develops that might
make operation unsafe.
• Do not use Rifton components or products for any purpose other than their intended
use.
• Replace or repair components or products that are damaged or appear to be unstable.
• Use only Rifton authorized replacement parts. Order information for replacement parts
is provided on the back of this product manual.
Cleaning
As needed, clean with disinfectant wipes or a solution of up to 10% bleach. Do not use
excessive amounts of water. Do not use pine oil cleaners.
Warranty Statement
If a Rifton product breaks or fails in service during the first year, we will replace it
free of charge.

11
Materials
• Steel hardware items (nuts, bolts, screws, etc) are typically zinc or nickel plated, or
stainless steel.
• Upholstery items (pads, support blocks, padded prompts, etc) are typically polyurethane
foam with a fire-retardant cover made from expanded vinyl.
• Frames are typically steel or aluminum tubing, welded together, and coated with a
baked-on paint finish. Some frame components may also be stainless steel.
• Straps are typically made of polypropylene or nylon webbing.
• Plastic components are typically injection molded from a variety of industrial resins.
All materials are latex, lead and phthalates free.
User modifications
To prevent serious injury or death, do not modify or alter Rifton
products or components, or use Rifton products or components
in conjunction with products from other manufacturers. Rifton does not accept
responsibility for any modifications or alterations made to our components or products
after they leave our premises. Customers modifying or altering our components or
products, or using them in conjunction with products from other manufacturers, do so
at their own risk.
WARNING

12
Rifton Contact Information
Mail
Rifton Equipment
PO Box 260
Rifton NY 12471–0260
Fax
800.865.4674
Phone
800.571.8198
9–5 EST
Online
www.Rifton.com
To order replacement parts
1. Locate the ID number of the product on the small white label.
2. Have this number available when you call 800.571.8198 for your
customer service representative.
Use only replacement parts supplied by Rifton Equipment.
We are glad to supply replacement parts. Although Rifton makes every effort to
supply correct parts and instructions for repairing or refurbishing your equipment,
you are responsible to make sure that the repairs or modifications are correctly and
safely completed.
@
Email
[e-mail]
CL75 ECO N/A Revision 00
Find important details and informative
facts about the Support Station at:
www.rifton.com/supportstation