ring Stick Up Cam Wired User manual

Stick Up Cam Wired

1. Set up your
Stick Up Cam Wired.

Download the Ring app.
The app walks you through setting up and managing
your Stick Up Cam Wired.
Search for “Ring” in one of the app stores below, or
visit: ring.com/app
Download from
Windows Store
Your Wi-Fi password
Grab your Wi-Fi password.
You’ll need it to set up your Stick Up Cam.
Write it down below so it’s handy when you need it:

Let’s get your Stick Up Cam ready.
First, slide off the bottom cover.
Do not reattach this cover until setup is complete!
Powering your Stick Up Cam
You can power Stick Up Cam in one of two ways: Plug it into
a socket (with USB), or power it with the included Ring PoE
Adapter, which supplies Power over Ethernet.
If you’re installing Stick Up Cam indoors, you can use either
power supply. For outdoors, use the PoE Adapter.
4

Feed the included USB cable through the hole in the bottom
cover and plug it into your Stick Up Cam.
Then, connect the cable to the included USB power supply,
and plug the power supply into a socket.
To power Stick Up Cam with USB:
(For indoor use only)
5

Feed an Ethernet cable through the hole in the bottom
cover and plug it into your Stick Up Cam. Then, hook it up
with the included PoE Adapter, following this diagram.
To power Stick Up Cam with the PoE Adapter:
(For indoor or outdoor use)
For outdoor use, install the PoE Adapter indoors, then
run an Ethernet cable outdoors to your Stick Up Cam.
6

Security Cams
Blue light flashing?
If the light on the front of your Stick Up Cam is flashing after
setup, it’s updating its software.
Do not unplug your Stick Up Cam while the light is flashing!
Set up your Stick Up
Cam in the Ring app.
In the Ring app, select
Set Up a Device.
When prompted, select
Security Cams and follow
the in-app instructions.
Try it out!
After setup, tap the Live View
button in the Ring app to
see live video from your Stick
Up Cam.

2. Install your
Stick Up Cam Wired.
Choose a location.
Stick Up Cam is happy just about anywhere, indoors or out.
It comes ready to sit on a flat surface like a table or shelf, but
can also be mounted to a wall or ceiling.
Choose a spot where it can provide the view you want,
within reach of a power outlet or an Ethernet port with PoE.
Table or shelf Mounted on a wall Mounted on a ceiling
8

How to use Stick Up Cam
on a table or shelf:
Make sure that any connected
cables have been routed
through the hole in the
bottom cover.
Then, slide the cover into
place on your Stick Up
Cam. Secure the cover with
the attached screw, using
the star-shaped end of the
screwdriver bit.
Finally, place Stick Up Cam in
your chosen position. Your
Stick Up Cam is now ready to
protect you.
9

Remove the plastic cover and
rubber pad from the base.
You’ll put the cover back on once
you’ve mounted your
Stick Up Cam.
Flip the base to the rear.
The base of the stand is hinged. Before wall-mounting, flip
the base down and behind your Stick Up Cam.
How to install Stick Up Cam
on a wall:
10

Push the rubber pad
back into the base.
The rubber pad should sit
between your wall and the
base of your Stick Up Cam.
Snap the cover back
onto the base.
Then, secure it with the
included security screw,
using the star-shaped end
of the screwdriver bit.
Now your Stick Up Cam
is installed and ready to
protect you.
Drive the screws.
Hold the round part of the base against your wall, rubber-
side down. Use the integrated level to ensure it’s straight.
Then mount it with the included screws.
11

How to install Stick Up Cam
on a ceiling:
Rotate the stand above the camera:
The whole stand can rotate on its axis. Before ceiling-
mounting, rotate the stand 180 degrees so the base is
positioned above your Stick Up Cam.
Remove the plastic cover
from the base.
You’ll put the cover back on once
you’ve mounted your
Stick Up Cam.
12

Drive the screws.
Hold the round part of the base against your ceiling,
rubber-side down. Then mount it with the included screws.
13

Close it up.
Make sure that any connected cables have been routed
through the hole in the bottom cover.
Then, slide the cover into place on your Stick Up Cam.
Secure it with the attached screw, using the star-shaped end
of the screwdriver bit.
Final steps for wall or
ceiling mounting:
14

Snap the cover back
onto the base.
Then, secure it with the included security screw, using the
star-shaped end of the screwdriver bit.
Now your Stick Up Cam is installed and ready to protect you.
15

For a list of all our customer support numbers, visit: ring.com/callus.
To review your warranty coverage, please visit www.ring.com/warranty.
Patents: www.ring.com/patents.
© 2018 Ring LLC or its affiliates.
RING, ALWAYS HOME, and all related logos are trademarks of Ring LLC or its affiliates.
Last updated: 11/15/18
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
[phone]
??ring.com/help