Rinnai RB-3SS-C User manual

•Confirm that the screws are secured firmly into the burner cover.
(Six screws are included.)
six
RB3SS-32-2x01
040113
•Installation on the table.
Table Casing Screw Casing
Stainless Top Plate / Tempered Glass
The fixing Screw x 6 pcs
THREE-BURNERS GAS COOKER
INSTRUCTION MANUAL
RB-3SS-C
Caution for the tempered glass
•Never use oversized cooking
utensils or overload the cooking
appliances.
•Do not remove the pan support and
enclose the burner with a wok stand
as this will concentrate and deflect
the heat onto the gas hob.
•Do not place anything, e.g., flame tamer, asbestos mat between pan and pan support as
serious damage to appliance may result.
•Do not place the cooker pan
over the pan support side as it
can cause tumbling.
•Use only a wok support
supplied or recommended by
the manufacturer of the
appliance.
GEN

Fig. 1
In order to obtain the best results and to maintain your Rinnai Built-In Hob in the best condition, please
read the instruction carefully.
Components and Features
- 6 -
Trouble Shooting Manual for Rinnai RB-3SS Built-in Hob
Maintenance
•Wipe the tempered glass with a soft damp cloth and mild detergent.
•Wash the Pan Support and Burner Covers in warm water and detergent.
- 1 -
Components and parts names
FAULT CAUSE
1. No Ignition Spark electrode is wet, especially in
high humidity season
Dry the electrode with clean tissue
or dry cloth.
2. Flame cannot be
held
Incorrect turning of gas control
knob.
Push and turn the gas control knob
anti-clockwise until a ‘click’ sound
is heard. Hold for a few seconds until
flame is ignited.
4. Yellow flame Accumulated grease and dirt
on the burner head.
Wash the burner head in warm water
with detergent. Leave it to dry; then
place it back in the correct position.
5. Unstable flame Incorrect location of the burner head. Refit the burner head into the burner
body
3. No main flame 3.1 Gas Regulator has been
turned off
Open gas regulator completely
3.2 Burner cap is blocked by
aluminum foil.
Remove aluminum foil.
REMEDY
Gas Inlet
(For Singapore model only)
T.G.
L.P.G.
Attention: when installing the casing
•
•Confirm that six screws are firmly secured into the casing.
Adjust screw position as bench cut out size.
Casing
Electrode
Knob
Safety Sensor
Stainless Top Plate
Burner Cap
Pan Support
H Burner Head
H Burner Body
H Burner Cover
Tempered Glass
RB-3SS
Pan Support
M Burner Head
M Burner Body
M Burner Cover
RB-3SS
RB-3SS
RB-3SS

RB-3SS
Installation
1. Pan Support
Fit Pan Support into Top Plate. (Fig.2)
2. Burner Head and Burner Cap
Fit burner head into burner cap onto the burner body correctly, without any gap. (see Fig.3)
3. Installation of Gas Hose
- 3 - - 4 -
Operating Instruction
Ignition
•Aspecific rubber hose for built-in hob must be used .
•The rubber hose must not be bent during installation and must be of an appropriate length
(less than 2 m).
•During installation, make sure that the rubber hose does not come into contact with the body of the
built-in hob pass through the bottom part of the built-in hob to prevent melting of the hose.
• Place the securing ring over the rubber hose and connect the rubber hose to the coupler below the
rear side of the built-in hob till the marked red line. Then secure the rubber hose in position with the
securing ring (For LP Gas).
• The connection must be performed by a qualified person according to the relevant standards
(For LP Gas). For Town Gas / Natural Gas, the task must be executed by a qualified licensed
technician.
•Do not use any other gas except for the ones indicated on the specification label of the built-in hob.
•LPG is the abbreviation for Liquefied Petroleum Gas, while TG is Town Gas supplied through
pipelines.
•For liquefied petroleum gas, please use conventional household low pressure regulators. The
standard pressure for LPG gas is 280 mm H O that for TG gas is 100 mm H O.
• Do not increase the gas pressure
• Never turn the LPG gas container upside down or subject to high temperatures or direct sunlight.
•Conversion of built-in hob from one gas type to another must be performed by a qualified
technician as major components need to be replaced.
2 2
1. Depress the control knob to about 2 mm and turn to the left (counter clock-wise) to the “ON”
position.
2. When the control knob is being turned for ignition, sparks are generated to ignite the burning
device, accompanied by clicking sound.
4. Precaution gas
GAP
GAP
(Fig.3)
Burner Cap
Burner Body
Burner Head
Spark Electrode
Safety Sensor
X
Fig. 2
•Install the built-in hob in well ventilated area and keep away from any combustible or
inflammable object i.e. paper, oil, etc.
•If the built-in hob is to be installed near any combustible surrounding i.e. wooden walls, wooden
shelves, etc, there should be a distance of more than 15cm (6 in) away from the surrounding
combustible. If the surrounding materials are fireproof, the clearance is not required.
•Place the built-in hob on a stable and level surface
• This built in hob is to be used for cooking purposes only. Do not use it to dry towel, clothes or any
other materials over it.
• Make sure that the following parts are fitted properly before use.

RB-3SS
Cut-Out Hole Size
Features
Specification
1. The tempered glass and stainless top plate is beautiful and stylish.
2.The enamel pan supports are durable and will not deform, making it stable for your cooking vessels.
3. The automatic continuous ignition device will ensure a 100% ignition rate.
4. Each built-in hob is equipped with a safety valve which will cut off the gas supply automatically if
the flame is accidentally extinguished (For SV model only).
3. Do not release the control knob for 2-5 seconds after the sparks have ignited the burner to activate the
safety device. Otherwise, the ignition will fail.
4. In the event of the burner flames being accidentally extinguished, turn off the burner control and do
not attempt to re-ignite the burner for at least 1 min.
The device shall not be operated for more than 15 seconds. If the burner has not lit up after 15
seconds, stop operating the built-in hob and open the compartment door and/or wait for at least 1
minute before attempting to ignite the burner again.
5. The flame can be controlled between “MAX” “MED”and “MIN” position, please adjust the flame
slowly.
6. For H burner, flame can be controlled with four combination, as shown by Fig. 4:
How to Handle Safety Device and Change Battery
- 5 -
7. Do not clean the top of the sensor with a hard brush, as it may damage the sensor.
1. After use, turn the control knob right to the “OFF” position, and the flame will be extinguished.
2. Make sure that the control knob is fully turned to the “OFF”position, less there would be a danger of
gas leakage.
3. After extinguishing the flame, do not touch the conductive parts of the hobs as they remain at very
high temperatures.
4. There may be a slight hissing sound after the flames is extinguished.
5. If the built-in-hob is not in use, turn off the main gas supply to avoid gas leakage or unnecessary
accidents.
Flame Extinguishing
Fig. 5
- 2 -
Gas Inlet
Front Side
”C” Size Battery
(1.5Vx1)
1. If the flame is extinguished during operation, the Flame Failure Safety Device will automatically cut
off the gas within second.
If you notice that the flame has been extinguished, please turn the knob to “OFF” position.
2. The Safety Sensor is delicate, please do not use stiff brushes or rough cleaning pads when cleaning.
•Aeration is preset at factory during assembly; please do not attempt to adjust it.
•Battery Box is located at bottom of right front (Size C, 1.5V x 1) (Fig.5).
Open the cabinet door, and change the battery.
out side flame
inside flame
: Max
: Max
: Off
out side flame
inside flame : Max
: Off
out side flame
inside flame : Min
out side flame
inside flame
: Medium
: Medium
Fig. 4
R0 ~ R110
725~840
65
435~480
550
Gas Type
Gas Consumption per hour
Respective gas consumption (kW)
Main
RHS / LHS (kW) Gas Connecting Tube
3.60
2.70
3.90
1.35
L.P.G (30 mbar)
Nozzle/injector size
4.20
0.95
Ø9.5 mm gas specific
rubber hose
½ In Thread (male)
Ø9.5 mm gas specific
rubber hose
Simmer
1.00
1.35
0.80
0.65
0.50
0.36
T.G. (8 mbar)
Nozzle/injector size
N.G. (25 mbar)
Nozzle/injector size
Main
Center
2.10
1.90
2.30
0.73
2.20
0.73
Product
Net Weight
Model
Automatic
Continuous Ignitions
Overall
Dimension
Cut out size
Built-in Hob
RB-3SS
17 Kg
21 Kg
435~480 mm x 725~840 mm
R0 mm ~ R110 mm
“C” Size Battery (1.5V x 1)
RB-3SS (S)
RB-3SS (GB)
RB-3SS (S)
RB-3SS (GB)
Diameters of pan which may be used on hob
* Use only flat bottom pan except for wok burner
Burners
280 mm
Max
Main
Min
120 mm
870 mm x 510 mm x 131 mm
880 mm x 520 mm x 131 mm