Rinnai Smart Port WF-60A1 Manual

Smart Port – Wi-Fi Kit
For Residential and
Light Commercial Air Conditioners
Operating & Installation Manual
HOME OWNER TO RETAIN FOR FUTURE REFERENCE
APPLY SPARE
QR CODE
LABEL

This page is intentionally blank

Rinnai 3 Wi-Fi Smart Port OIM
Congratulations on the purchase of a Rinnai Smart Port which
is compatible with selected Rinnai and Brivis Air Conditioners.
Terms and Conditions
Please read Terms and Conditions carefully before proceeding
with downloading the App.
Disclaimer
IMPORTANT NOTICE: This document is a guide only.
Laws, regulations and industry standards can vary between
States and Territories. Accordingly, this guide must be read
in conjunction with, and subject to, all laws, regulations and
industry standards applicable in the State or Territory in which
the products are installed. You must ensure that the installation
of the products will comply with those laws, regulations
and standards, and that the products recommended to
customers are t for the purpose for which they are intended.
Privacy Notication
Rinnai Australia Pty Ltd will collect personal information when
warranty and maintenance registration forms are completed.
This personal information is collected under the guidance of the
Privacy Information Protection Act 1998.
The purpose of collecting this information is to:
• process customer requests for us to provide service activities;
• register purchases of equipment for warranty;
• register requests for a survey/quotation for heating, ventilation,
and air conditioning goods and services.
The intended recipients of the information are:
• employees of Rinnai.
• federal and state governments who may require the information
for administration purposes.
While the supply of the information is voluntary, if our customers
cannot, or do not wish to provide the information sought, the
company may not be able to provide the services requested. If
information has already been provided, an application can be
made for access or amendment of that information, or to request
that it not be used. Customers have a right of access to, and
correction of, the information concerning them in accordance with
the relevant procedures under the Act.
Enquiries concerning this matter can be addressed to the
Business Practices O󰀩cer using the ‘Contacts’ on page 36.
Shall
Indicates a mandatory requirement of this manual.
Should
Indicates a recommended requirement of this manual.
Any deviations from these instructions may, at the discretion of the
manufacturer, void the warranty. As a result, the customer and/or
installer may be charged a fee for non-product warranty related
call outs. Also note that failure to comply with these instructions
may preclude company service personnel from being able to
service the device.

Rinnai 4 Wi-Fi Smart Port OIM
General Compatibility
All the following Rinnai (and Brivis) branded Residential and Light
Commercial products that have a “CN40” terminal on the PCB of
the INDOOR UNIT, are compatible for use with the Smart Port
accessory module.
• Ducted Inverter
• Cassette Inverter
• Slim Ducted Multi Inverter
• Compact Cassette Multi Inverter
For multiple INDOOR UNIT installations, one Smart Port is
required for each INDOOR UNIT.
Contact Rinnai Technical Support for further information.

Rinnai 5 Wi-Fi Smart Port OIM
WARNINGS AND IMPORTANT INFORMATION
IMPORTANT
READ ALL INSTRUCTIONS BEFORE USING THE DEVICE AND APP.
Always comply with the following precautions to avoid dangerous situations and to ensure optimum performance.
Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property
damage, personal injury and/or death.
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in personal injury or death.
WARNINGS: Indicates a potentially hazardous situation which, if not avoided, could result in personal injury or
death.
CAUTIONS: Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate
injury or damage to the appliance. It may also be used to alert against unsafe practices.
NOTE
Read all the safety precautions carefully before installing the unit.
Outlined below are important safety guidelines which must be followed.
Applicable system: iOS and Android. Recommended iOS 9.0 and above, Android 4.0 and above.
Due to special circumstances which may occur, not all Android and iOS systems are compatible with the App.
The manufacturer will not be held responsible for any incompatibility issues.
The manufacturer will not be held liable for any issues and problems caused by the internet, Wi-Fi router and Smart
devices. Please contact the original provider for further help.
Wireless safety strategy
• Smart Port only supports WPA-PSK/WPA2-PSK encryption and non encryption.
NOTE
Smart Phone camera needs to be 5 million pixels or above to ensure QR code scans clearly.
Depending on your network, time-out may occur. Therefore, it may be necessary to repeat network conguration.

Rinnai 6 Wi-Fi Smart Port OIM
NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment o󰀨 and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
NOTE
• The supplied remote control is used to congure and connect to Wi-Fi.
• The supplied remote should be retained in the event the connection needs to be established or set up needs to
be repeated.
• The supplied remote control can also be used to operate the system if the original system was supplied with a
remote control. Point remote control towards the Smart Port Receiver.
NOTE
A NOTE ON ILLUSTRATIONS
The illustrations used in this manual are for explanatory purposes only and the shape of your unit may vary slightly
from that which is shown in this manual.
• The ‘Nethome Plus’ App conguration and user screens are subject to change.
NOTE
With our policy of continuous improvement, we reserve the right to change, or discontinue at any time, specications,
design, illustrations and content without notice. Pictures for illustration purposes only.

Rinnai 7 Wi-Fi Smart Port OIM
1.0 TABLE OF CONTENTS
1.0 Specications 8
2.0 SmartPortKit 8
2.1 Kit Contents. ................................................................9
2.2 Dimensions ................................................................10
3.0 Installation 10
3.1 Smart Port Wiring ......................................................10
3.2 Location .....................................................................10
3.3 Smart Port Without Wired Controller .........................11
3.4 Smart Port With Wired Controller ..............................14
4.0 DownloadandInstallApp 18
5.0 UserRegistration 19
6.0 NetworkConguration 20
6.1 Conguration–Android ............................................21
6.2 Conguration–iOS ..................................................25
7.0 UsingTheApp 30
8.0 SpecialFunctions 31
Contacts 36

Rinnai 8 Wi-Fi Smart Port OIM
1.0 SPECIFICATIONS
Model WF-60A1
Standard IEEE802.11b/g/n
Antenna Type External omnidirectional Antenna
Frequency Wi-Fi: 2.4G
Maximum Transmitted Power 15dBm Max
Operation Temperature 0°C~45°C/32°F~113°F
Operation Humidity 10%~85%
Power Input DC 5V/300mA
Remote Control Battery Rated Voltage - 3.0V (2 x AAA
1.5 Volt Batteries)
1.
2.0 SMART PORT KIT
Do not install the Smart Port in areas covered in heavy oil, vapor
or sulphur gases, otherwise this product will react and may lead
to system malfunction.
Kit Contents – See Figure 1
No. Description Qty
1 Smart Port (Receiver) 1
2
Looms
CN2 – 1
3 Extension (6m) PN: B026005 1
4 CN40 DRCi PN: B080175 1
5 Remote Control for Setup 1
6 Smart USB 1
7 Smart Port Unique ID QR Label 1
8 Screws (M4X20) 3
9 Wall Plugs 3
10 AAA Batteries (1.5 Volts) 2
11 Operating and Installation Manual 1
Please check that all parts have been supplied.

Rinnai 9 Wi-Fi Smart Port OIM
2.1 KIT CONTENTS.
Figure 1. What’s in the box
1
2
89
Smart Port
for Ducted Reverse Cycle Air Conditioners
Operating & Installation Manual
PLEASE RE TAIN FOR FUTURE REFERENCE
7
6
10
3
5
11
4
Smart Port – Wi-Fi Kit
For Residential and
Light Commercial Air Conditioners
Operating & Installation Manual
HOME OWNER TO RETAIN FOR FUTURE REFERENCE
APPLY SPARE
QR CODE
LABEL

Rinnai 10 Wi-Fi Smart Port OIM
2.2 DIMENSIONS
Figure 2. Dimensions
Figure 3. Components
Front Cover
Backing Plate
Front Cover
Internal PCB Plate
Backing Plate
3.0 INSTALLATION
3.1 SMART PORT WIRING
Determine wiring conguration of your Smart Port before
commencing.
For installations without wired controller, refer to Section 3.3.
For installations with wired controller, refer to Section 3.4.
3.2 LOCATION
• Indoors only
• Internal plaster wall or ceiling
The Smart Port shall be positioned in a waterproof environment
within 10m of your wireless router (where applicable) to ensure
reliable communication. If this distance is more than ten meters
the transmitting signal may be predisposed to interruption. Please
consult your installer in the rst instance if this issue is identied.
The environment must not exceed a temperature of 70°C and
relative humidity of 85%.
IMPORTANT
The Smart Port MUST NOT be installed inside
any appliance cabinet as this will adversely a󰀨ect
the Wi-Fi connection. Do not position outside or
under oor.

Rinnai 11 Wi-Fi Smart Port OIM
3.3 SMART PORT WITHOUT WIRED CONTROLLER
Figure 4.
Fit the looms supplied as shown in Figure 4.
One side is connected into port CN40 on the indoor unit main
PCB. The other loom is plugged into CN2 on the Wi-Fi Smart Port
terminal.
If you require more than a 6m loom extension, you can order
an additional 6m extension from the manufacturer. Rinnai Part
Number B026005.
Smart Port
Indoor Main PCB
Loom CN2
Loom Extension (6m)
Loom CN40 DRCi
CN40
CN2
CN3

Rinnai 12 Wi-Fi Smart Port OIM
Assembly of Smart USB
1. Carefully remove the Backing Plate by inserting a slot
screwdriver into the slots as shown in Figure 5 in the lower
part of the Smart Port (2 places), and lever up to remove the
Smart Port base.
Figure 5.
2. Insert Smart USB into the main PCB of the Smart Port. Refer
to Figure 6.
Figure 6.
Backing Plate Slots
Push
3. Determine path of Looms to exit Backing Plate.
4. For rear exit of Backing Plate, remove and discard the
perforated rectangle Knock-Out Plate as shown in Figure 7.
Figure 7.
5. For above or below Backing Plate, see route options as
shown in Figure 8.
Figure 8.
Remove Knock-Out Plate
Discard
OR

Rinnai 13 Wi-Fi Smart Port OIM
6. Fasten the Backing Plate of the Smart Port
• For exposed mounting, fasten the Backing Plate with the
screws and plugs supplied if required. Refer to Figure 9.
Figure 9.
Wiring the Smart Port
A. For exposed wire mounting, two outlet positions
Figure 10.
Backing Plate
Screws
(M4×20)
Note
orientation
Top side
wire outlet
Bottom side
wire outlet
B. Shielded Wiring
Figure 11.
CAUTION
Avoid water entering into the Smart Port. Trap
loom and then putty to seal the connection wires
during installation. See Figure 12. When installing,
save a length of loom for convenience to remove
the Smart Port during maintenance.
Figure 12.
Wiring through the wall
Wiring hole and wall hole
Diameter of wall hole:Φ20mm
Remove
knock-out
plate
Putty
(field
supplied) Trap
Trap
Putty
(field
supplied)

Rinnai 14 Wi-Fi Smart Port OIM
3.4 SMART PORT WITH WIRED CONTROLLER
If you want to use both the wired controller and the Wi-Fi control
at the same time, you can use the CN3 port on the Smart Port
terminal to connect the wired controller as shown in Figure 13.
Figure 13.
Smart Port
Loom CN40 DRCi
Loom extension (6m)
Wired controller
CN2
CN3
Indoor Main PCB
Loom CN2
Loom extension (6m)
Loom CN40 DRCi
CN40

Rinnai 15 Wi-Fi Smart Port OIM
Assembly of Smart USB
1. Carefully remove the Backing Plate by inserting a slot
screwdriver into the slots as shown in Figure 14 in the lower
part of the Smart Port (2 places), and lever up to remove the
Backing Plate.
Figure 14.
2. Insert Smart USB into the main PCB of the Smart Port. Refer
to Figure 15.
Figure 15.
Backing Plate Slots
Push
3. Remove the front cover by inserting a screwdriver into the
slot as shown in Figure 16, and slowly and carefully lever
down to remove.
Figure 16.
4. Install Loom CN40 DRCi (supplied) into CN3 port.
• Use the CN40 loom to connect the wired controller to the
CN3 terminal of the Smart Port. See Figure 17.
Figure 17.
CN3

Rinnai 16 Wi-Fi Smart Port OIM
5. Determine path of Looms to exit Backing Plate.
6. For rear exit of Backing Plate, remove and discard the
perforated rectangle Knock-Out Plate as shown in Figure 18.
Figure 18.
7. For above or below Backing Plate, see route options as
shown in Figure 19.
Figure 19.
Remove Knock-Out Plate
Discard
OR
8. Fasten the Backing Plate of the Smart Port
• For exposed mounting, fasten the Backing Plate on the wall
with the screws and plugs supplied. Refer to Figure 20.
Figure 20.
Wiring the Smart Port
A. For exposed mounting, two outlet positions
Figure 21.
Backing Plate
Screws
(M4×20)
Note
orientation
Top side
wire outlet
Bottom side
wire outlet

Rinnai 17 Wi-Fi Smart Port OIM
B. Shielded Wiring
Figure 22.
CAUTION
Avoid water entering into the Smart Port. Trap
loom and then putty to seal the connection wires
during installation. See Figure 23. When installing,
save a length of loom for convenience to remove
the Smart Port during maintenance.
Figure 23.
Wiring through the wall
Wiring hole and wall hole
Diameter of wall hole:Φ20mm
Remove
knock-out
plate
Putty
(field
supplied) Trap
Trap
Putty
(field
supplied)
9. Reattach the front cover
• After aligning the front cover, carefully clip onto Internal PCB
Plate and taking care to avoid clamping the loom during
installation. Refer to Figure 24.
Figure 24.

Rinnai 18 Wi-Fi Smart Port OIM
4.0 DOWNLOAD AND INSTALL APP
Quick Start Guide
1. Download App ‘Nethome Plus’
2. In settings, Turn o󰀨 ‘Mobile data’
3. Open ‘Nethome Plus’ App
4. On the Remote Control, press ‘LED’ 7 times (No audible
beep or display of AP)
5. Once conguration is complete, turn on mobile data
Scan QR Code to download APP
QR Code A (Android) QR Code B (iOS)
Android Phone Users
Android Phone users: scan QR Code A or go to Google Play,
search ‘Nethome Plus’ app and download APP.
iPhone Phone Users
iPhone Users: scan QR Code B or go to App Store, search
‘Nethome Plus’ app and download APP.

Rinnai 19 Wi-Fi Smart Port OIM
5.0 USER REGISTRATION
• Download App ‘Nethome Plus’
NOTE
Please ensure your mobile device is connected
to the Wi-Fi router. Make sure the Wi-Fi router is
connected to the internet before completing user
registration and network conguration.
• If you do not have an account Click ‘Create Account’.
• Click ‘OK’. and proceed to
your email account

Rinnai 20 Wi-Fi Smart Port OIM
• An email will be sent for you
to activate your account to
complete your registration.
• Follow prompts and read
carefully before you agree
to the terms and conditions.
6.0 NETWORK CONFIGURATION
CAUTION
You must select your Wi-Fi network for
successful registration. Turn o󰀨 your ‘mobile
data’.
Make sure the Android or iOS device connected
to your Wi-Fi is functioning well and can
connect back to your original Wi-Fi network
automatically.
Enter the AP mode description.
Use the Remote Controller to enter AP mode. Aim the remote
control at the Smart Port, then press the L.E.D ‘Follow Me’ button
seven times within 3 minutes. The indicator L.E.D of the Smart
Port will ash (indicating AP mode).
NOTE
When your Air Conditioner (AC) enters into ‘AP’
mode, the air-conditioning remote controller
can’t control it. It is necessary to nish network
conguration or power the AC again in order to
control it. Alternatively, you need to wait 8 minutes
to let the AC quit ‘AP’ mode automatically.