Rinnai CNTRLDRCINW Specification sheet

Wired Remote Controller
Operation and Installation Manual
MODEL
CNTRLDRCINW

Congratulations on the purchase of your Rinnai
Wired Remote Controller.
This manual describes safety precautions required
for the use of the product.
• Read this manual carefully before installing or
operating your wired remote controller. Make
sure you understand the information provided
before attempting to use the product.
• Keep this manual where it is readily accessible
after reading it through.
• If another user operates the product in the future,
be sure to hand over this manual to the new user.
• All the pictures in this manual are for explanation
purpose only. They may be slightly di󰀨erent from
the wired remote controller you purchased and
the actual shape shall prevail.

Rinnai 3 DRCi R32 Wired Controller OIM
This Wired Controller is compatible with the following Rinnai indoor models:
DRCi Hi-Wall Slim Ducted Cassette
DINLR07B1 HINRP20M DINSD26MB CIN20RMB
DINLR09B1 HINRP26M DINSD35MB CIN26RMB
DINLR11B1 HINRP35M DINSD50MB CIN35RMB
DINLR13B1 HINRP50M DINSD70MB CIN50RMB
DINLR15B1 HINRP60M
DINLR18B1 HINRP70M
NOTE
This controller contains features and functions that are applicable
to certain models in 1:1 and Multi congurations. In brackets
next to the associated feature or function the applicable models
will be listed, If no models are listed the feature or function is
applicable to all.
1:1 - This conguration contains one outdoor unit and one indoor unit.
Multi - This conguration contains one outdoor unit and two or more indoor
units. The only models that may be installed in a multi conguration are Hi-Wall,
Cassette, and Slim Ducted units, DRCi is a 1:1 conguration.

Rinnai 4 DRCi R32 Wired Controller OIM
1.0 TABLE OF CONTENTS
1. Safety Precautions 7
2. Accessory Installation 9
3. Installation Method 10
Wired remote controller dimensions ................................................................10
Battery Installation (CR2032) ...........................................................................12
Thermostat connection to Indoor Unit ..............................................................13
Setting up two Controllers ................................................................................13
4. Specications 17
Wiring Specications........................................................................................17
5. Features 18
Feature and functions of the wired controller ...................................................18
6. LCD Display 19
7. Controller buttons 20
8. Settings prior to Operation 21
Setting the current day and time ......................................................................21

Rinnai 5 DRCi R32 Wired Controller OIM
9. Operation 22
To start/stop operation......................................................................................22
To set the operation mode ...............................................................................22
Room temperature setting................................................................................23
Fan speed setting.............................................................................................23
Keypad tone setting .........................................................................................23
Child lock function ............................................................................................24
Swing function..................................................................................................24
Swing function..................................................................................................25
Turbo function .................................................................................................26
Active Clean ....................................................................................................26
Follow me function indicator.............................................................................26
10. Timer Functions 27
To set the On or O󰀨 Timer................................................................................28
To set the On and O󰀨 Timer .............................................................................29
11. Weekly Timer 1 30
WEEKLY timer operation..................................................................................32
Delay function ..................................................................................................34
12. Weekly Timer 2 36
Delete the time scale in one day ......................................................................42

Rinnai 6 DRCi R32 Wired Controller OIM
13. Fault Codes 43
Fault Alarm Handling........................................................................................43
Technical Requirements...................................................................................43
14. Wireless Control Connection 44
Safety Precautions ...........................................................................................44
Wireless safety strategy ...................................................................................44
Download and Install APP................................................................................45
15. User Registration 46
16. NetworkConguration 48
Network conguration by Bluetooth scan......................................................... 49
Network conguration by selecting appliance type .........................................53
17. How to Use App 58
Special Functions.............................................................................................60
18. Warranty 64
Contacts 68

Rinnai 7 DRCi R32 Wired Controller OIM
1. SAFETY PRECAUTIONS
IMPORTANT
• This wired controller must be installed only by an Authorised
Person.
• Installation by other persons may lead to imperfect installation,
electric shock or re.
• Adhere to this installation manual.
• Improper installation may lead to electric shock or re.
• Reinstallation must be made by an Authorised Person.
• Do not uninstall the unit randomly. Arbitrarily uninstalling may
lead to abnormal operation, heating or re of the air condition.
NOTE
• Do not install the unit in a place vulnerable to leakage or
ammable gases. Once ammable gases are leaked and left
around the wire controller, re may occur.
• Do not operate with wet hands or let water enter the wired
controller. Otherwise, electric shock may occur.
• The wiring should adapt to the wired controller’s current.
Otherwise, electric leakage or heating may occur and result
in re.
• The specied cables shall be applied in the wiring. No external
force may be applied to the terminal.
• The illustrations used in this manual are for explanatory
purposes only.

Rinnai 8 DRCi R32 Wired Controller OIM
CAUTION
BEFORE INSTALLING THE WIRED CONTROLLER
• This manual provides instructions for installing the wired
controller. Please refer to the wiring diagram of this installation
manual for connecting the wired controller with indoor unit.
• The wired controller operates in a low voltage loop circuit.
Strictly DO NOT directly contact the high voltage cable
above, such as 115V,220V,380V. DO NOT wire this type of
cabling in the said loop; wiring clearance between congured
tubes should range between 300~500mm or above.
• The shielded wire of the wired controller must be grounded
rmly.
• After completing the wire controller connection, DO NOT use
Megger tester to check the insulation. That may damage the
product.
NOTE
A maximum of two controllers may be installed on a system and
the mix may contain any of the following three controllers:
CNTRLDRCINW / CNTRLDRCIPW / CNTRLDRCIPB

Rinnai 9 DRCi R32 Wired Controller OIM
2. ACCESSORY INSTALLATION
Select the installation location
Don’t install at the place where cover with heavy oil, vapor or sulfureted gas,
otherwise, this product would be deformed that would lead to system malfunction.
Preparation before installation
1. Please conrm that all the following parts have been supplied.
No. Name Qty Remarks
1 Wired Controller 1 —
2 Operation & Installation Manual 1 —
3 Screws 3 ST 3.9*25 (For mounting on the wall)
4 Wall Plugs 3 For Mounting on the Wall
5 Battery (CR2032) 1 —

Rinnai 10 DRCi R32 Wired Controller OIM
3. INSTALLATION METHOD
Wired remote controller dimensions
Figure 1. Dimensions
Remove backing plate from the wired controller
• Insert a at screwdriver into the
slots in the lower part of the wired
controller (2 places). Rotate the
screwdriver (2 places) to remove the
backing plate (Figure 2).
Srewdriver
locations
Backing
plate
Figure 2. Backing plate removal
NOTE
Do not pry up and down, you can only rotate the screwdriver.

Rinnai 11 DRCi R32 Wired Controller OIM
NOTE
The PCB is mounted in the upper part of the wired controller. Be
careful not to damage the board with the slot screwdriver.
Fasten the backing plate of the wired controller
• Fasten the backing plate on the wall with the 3 screws (ST3.9*25) and plugs
(Figure 3) provided.
Figure 3.
Loom access point
• Remove plastic knockout from the backing plate (Figure 4).
• Create a hole in the wall to access the wall cavity for routing the loom from FCU
to controller.
Remove knockout
NOTE
Put on a at surface.
Be careful not to distort
the back plate of the
wire controller by over
tightening the mounting
screws.
Figure 4.

Rinnai 12 DRCi R32 Wired Controller OIM
Battery Installation (CR2032)
• Slide the battery into the holder as shown with the
positive side facing up (Figure 5).
• Put the battery into the installation site and make sure
the positive side of the battery is in accordance with
the positive side of installation site.
• On the rst power up set the time of day. If the system
is exposed to a power outage the battery will maintain
the time of day. If the displayed time is not correct
once power is restored replace the battery. Figure 5.
NOTE
All the illustrations in this manual are for explanation purposes
only. Your wired controller may be slightly di󰀨erent. The actual
shape shall prevail.
Dispose of used button batteries immediately and safely. Flat batteries can still be dangerous and may be a choking hazard.
Inform others about the risk associated with button batteries and how to keep their children safe.
Remove the batteries if the remote is not going to be use for prolonged periods. This will help prevent damage from leaking
batteries. If leakage has occurred and corrosion is evident the remote will need to be replaced.
Leaking chemicals are toxic and MUST NOT be touched or ingested.
NEVER mix old and new batteries.
DO NOT immerse the remote control in any liquid, this will damage the remote control, rendering it inoperable and voiding
its warranty.
WARNING KEEP BATTERIES OUT OF REACH OF CHILDREN.
Swallowing may lead to serious injury in as little as 2 hours or death, due to chemical burns
and potential perforation of the oesophagus.
If you suspect your child has swallowed or inserted a button battery immediately call the
24-hour Poisons Information Centre on 13 11 26 for fast, expert advice.
Examine devices and make sure the battery compartment is correctly secured, e.g.
that the screws or other mechanical fasteners are tight. DO NOT use if compartment is not secure.











Rinnai 13 DRCi R32 Wired Controller OIM
Thermostat connection to Indoor Unit
Figure 6. Model A
Setting up two Controllers
To congure a secondary CNTRLDRCINW controller do the following:
Loom
knockout
Indoor Unit
PCB
With both controllers connected, turn power
to the system ON at the isolating switch.
Go to the proposed secondary controller
and press the copy button.
1
2
3
4
Press the confirm button to access parameters.
Press the up button until ‘ - - ’ and ‘Adr’ appear on
the screen as shown below.

Rinnai 14 DRCi R32 Wired Controller OIM
Wi-Fi control may be setup on one of the controllers only. There is no polarity
between HA and HB (Figure 7).
SUB will appear on the right hand side of the
screen confirming setup of the secondary
controller is complete.
7
8
9
10
5
6
Press the Confirm button to accept address changes.
Press the Confirm button to access controller
address options.
Press the Up button until ‘ ’ appears as shown below.
Setting Time and Date Weekly Schedule Timer On / Off
Press the back button twice to save and return to the
home screen.
The system may now be operated by either controller. If two controllers
are installed the secondary ‘SUB’ controller is not capable of the
following functions:

Rinnai 15 DRCi R32 Wired Controller OIM
Figure 7.
NOTE
DO NOT allow water to enter the wired control. Use the trap and
putty to seal the wires. Connecting wires must be xed reliably
and cannot be pulled.
For some units, one wired controller can support multiple units (a maximum of
16 units). For conguration of multiple indoor units loom connection is polarity
sensitive and HA must connect to HA on all indoor units, the same applies to HB.
In group control, there will be no error displayed on the wired controller (Figure 8).
Figure 8.
Total length 40m maximum
Maximum 40m
Maximum
40m
Earth the
shield

Rinnai 16 DRCi R32 Wired Controller OIM
Indoor Unit
Connect the terminals on the wired controller (HA ,HB), and the terminals of the
indoor unit (HA ,HB). There is no polarity between HA and HB (Figure 9).
Figure 9.
Reattach backing plate of the wired controller
To reconnect the fascia to the backing plate, anchor the top lugs rst as shown
below then swing the fascia down and press lightly to engage the bottom tabs, be
careful not pinch the loom during this process (Figure 10).
Figure 10.
HA HB
Indoor Unit
Wired Controller

Rinnai 17 DRCi R32 Wired Controller OIM
4. SPECIFICATIONS
Model CNTRLDRCINW
Input Voltage 5V~24V
Ambient Temperature -5~43°C
Ambient Humidity RH40%~RH90%
Wiring Specications
NOTE
Controller loom shall be 2-Core shielded cable, 2 x 0.5mm.sq
minimum, Rinnai part number CNTRLLOOM2W18M is 18m long
and it may be used.

Rinnai 18 DRCi R32 Wired Controller OIM
5. FEATURES
Feature and functions of the wired controller
• LCD Display.
• Malfunction Code Display:
shows the error code which is
ideal for service.
• No raised section at back-end
so more convenient to t the
wires and install the device.
• Room Temperature Display.
• Weekly Timer.
Function:
• Mode: Choose Auto-Cool-Dry-Heat-Fan
• Fan speed: Auto/Low/Med/High speed
• Swing (1:1 & Multi – Hi-Wall)
• Timer ON/OFF
• Temp Setting
• Weekly Timer
• Follow Me
• Turbo
• 24-hour System
• 12-hour System
• Auto Restart
• Automatic Airow Test (DRCi)
• Dual Control
• Group Control
(1:1 – DRCi / Cassette)
• Child Lock
• LCD Display
• Clock

Rinnai 19 DRCi R32 Wired Controller OIM
6. LCD DISPLAY
(1:1 - DRCi / Hi-Wall / Cassette)
(1:1 & Multi - Cassette /
Hi-Wall / Slim Ducted)
(1:1 - DRCi / Cassette / Hi-Wall)

Rinnai 20 DRCi R32 Wired Controller OIM
7. CONTROLLER BUTTONS
1
2
3
4
5
6
FAN SPEED
MODE
FUNCTION
SWING (1:1 & Multi –
Hi-Wall / Cassette )
ADJUST
TIMER
7
8
9
10
11
COPY
POWER
CONFIRM
BACK
DAY OFF/DELAY (1:1 – DRCi /
Cassette)