Risco RWX73F User manual

1
Door / Window Sensor
Model RWX73F
Installation instructions
1 General Description
The 2-Way door / window sensor offers protection against opening doors
and windows. In additon, the sensor incorporates a high-security anti-
sabotage feature.
2 Quick Device Allocation
The door / window magnet must identify itself to the WiComm Smart Hub.
This can be performed either using the RISCO Express Wizard
(www.riscocloud.com/express) by adding the extra sensor at the time of the
Smart Hub system installation or later either by using the “Settings” on the
Web (www.riscocloud.com) or using the WiComm Smart Hub, as follows:
1. Press the button on the WiComm Smart Hub for 5 seconds; the
unit beeps once as it enters Learn mode (all the LEDs also light up,
one after the other).
2. Detach the back of the sensor from the mounting bracket (See Figures
3A and 3B)
3. Remove sensor’s red battery isolation strip (See Figure 2)
4. Put back the mounting bracket to send a signal transmission; the
WiComm Smart Hub beeps once to accept or beeps three times to reject.
Once accepted, the system announces the device type and its zone (for
example, “Sensor, zone 1”).
5. To complte allocation momentarily pressWiComm Smart Hub button
. A short beep is heard and the LEDs stop flashing.
6. Mount the detector
7. You can change the zone labels through the www.riscocloud.com
website (for details, see the Reference Manual).
Note: For future use, it is recommended to write down the sensor
description, zone number, and installation location of each allocated
detector.
3 Mounting the Door / Window Sensor
You can mount the door / window
sensor either using screws or adhesive
tapes.
Select a location best suited for
communication quality. RISCO
recommends placing the unit at the
highest possible position.
Figure 1
Mounting with Adhesive Tape
1. Peel the two-sided adhesive tapes from the sensor and magnet and
temporarily attach the unit to this point.
Door /
Window
Sensor
Magnet
Figure 2
2. Generate an alarm signal and verify that the receiver has received the
signal. If the alarm signal is not detected, reposition the sensor and try
again.
Mounting with Screws
1. Detach the back of the sensor from the mounting bracket (Fig. 2A). At
mounting location note the alignment marks for both components (Fig.
2B), and then install accordingly using 2 mounting screws and back
tamper screw (Fig 2C).
2. Detach magnet casing (Fig. 2D) and install with mounting screws (Fig
2E).
Figure 3
Figure 4
Notes:
1. It’s best to mount the
transmitter on the non-moving
part (door/window frame),
and the magnet on the
moving part.
2. The mark on the magnet's
case must be aligned with
the mark on the
transmitter's case (Fig. 3).
4 Replacing Battery
1. Release screw using a Phillips screwdriver (A) and then insert a flathead
screwdriver into the slot and twist to open cover (B).
Figure 5
2. Insert the battery while observing + - polarity.
Figure 6
3. Put back cover firmly into place and secure with screw.
Red battery
isolation strip
Adhesive
ta
p
e
Adhesive
ta
p
e

2
Figure 7
CAUTION: Risk of explosion if battery is replaced by an incorrect type.
Dispose of used batteries according to local regulations.
5 LEDS indication
LED Status Indication
Short blinks Successful enrollment
Short blink upon
transmission
Normal operation
Short flash sequence
during transmission
Low Battery
6 Technical Specifications
Electrical
Battery Type CR123 3V Lithium Battery
Current consumption 22μA standby
Frequency 915 MHz
Dead Time (HOLD ON) 2.5 minutes
Supervision Transmission 0-255 minutes
Battery Life 3 years typical
Contact size 32 x 35 x 72 mm (1.3 x 1.4 x 2.8 in.) Magnet
Size: 16 x 11 x 72 mm (0.6 x 0.44 x 2.8 in.)
Environmental
Operating temperature 0°C to 40°C (32°F to 104°F)
Storage temperature 20°C to 60°C (-4°F to 140°F)
* Specifications are subject to change without prior notice
Standard Limited Product Warranty (“Limited Warranty”)
RISCO Ltd. (“RISCO") guarantee RISCO’s hardware products (“Products”) to be free from
defects in materials and workmanship when used and stored under normal conditions and in
accordance with the instructions for use supplied by RISCO, for a period of (i) 24 months from
the date of delivery of the Product (the “Warranty Period”). This Limited Warranty covers the
Product only within the country where the Product was originally purchased and only covers
Products purchased as new.
Contact with customers only. This Limited Warranty is solely for the benefit of customers
who purchased the Products directly from RISCO or from an authorized distributor of RISCO.
RISCO does not warrant the Product to consumers and nothing in this Warranty obligates
RISCO to accept Product returns directly from end users who purchased the Products for their
own use from RISCO’s customer or from any installer of RISCO, or otherwise provide warranty
or other services to any such end user directly. RISCO’s authorized distributor or installer shall
handle all interactions with its end users in connection with this Limited Warranty. RISCO’s
authorized distributor or installer shall make no warranties, representations, guarantees or
statements to its end users or other third parties that suggest that RISCO has any warranty or
service obligation to, or any contractual privy with, any recipient of a Product.
Remedies. In the event that a material defect in a Product is discovered and reported to
RISCO during the Warranty Period, RISCO shall accept return of the defective Product in
accordance with the below RMA procedure and, at its option, either (i) repair or have repaired
the defective Product, or (ii) provide a replacement product to the customer.
Return Material Authorization. In the event that you need to return your Product for repair or
replacement, RISCO will provide you with a Return Merchandise Authorization Number
(RMA#) as well as return instructions. Do not return your Product without prior approval from
RISCO. Any Product returned without a valid, unique RMA# will be refused and returned to
the sender at the sender’s expense. The returned Product must be accompanied with a
detailed description of the defect discovered (“Defect Description”) and must otherwise follow
RISCO’s then-current RMA procedure published in RISCO’s website at www.riscogroup.com
in connection with any such return. If RISCO determines in its reasonable discretion that any
Product returned by customer conforms to the applicable warranty (“Non-Defective
Product”), RISCO will notify the customer of such determination and will return the applicable
Product to customer at customer’s expense. In addition, RISCO may propose and assess
customer a charge for testing and examination of Non-Defective Product.
Entire Liability. The repair or replacement of Products in accordance with this Limited
Warranty shall be RISCO’s entire liability and customer’s sole and exclusive remedy in case a
material defect in a Product is discovered and reported as required herein. RISCO’s obligation
and this Limited Warranty are contingent upon the full payment by customer for such Product
and upon a proven weekly testing and examination of the Product functionality.
Limitations. This Limited Warranty is the only warranty made by RISCO with respect to the
Products. The warranty is not transferable to any third party. To the maximum extent permitted
by applicable law, this Limited Warranty shall not apply and will be void if: (i) the conditions set
forth above are not met (including, but not limited to, full payment by customer for the Product
and a proven weekly testing and examination of the Product functionality); (ii) if the Products
or any part or component thereof: (a) have been subjected to improper operation or installation;
(b) have been subject to neglect, abuse, willful damage, abnormal working conditions, failure
to follow RISCO’s instructions (whether oral or in writing); (c) have been misused, altered,
modified or repaired without RISCO’s written approval or combined with, or installed on
products, or equipment of the customer or of any third party; (d) have been damaged by any
factor beyond RISCO’s reasonable control such as, but not limited to, power failure, electric
power surges, or unsuitable third party components and the interaction of software therewith
or (e) any failure or delay in the performance of the Product attributable to any means of
communication provided by any third party service provider, including, but not limited to, GSM
interruptions, lack of or internet outage and/or telephony failure. BATTERIES ARE
EXPLICITLY EXCLUDED FROM THE WARRANTY AND RISCO SHALL NOT BE HELD
RESPONSIBLE OR LIABLE IN RELATION THERETO, AND THE ONLY WARRANTY
APPLICABLE THERETO, IF ANY, IS THE BATTERY MANUFACTURER'S WARRANTY.
RISCO does not install or integrate the Product in the end user’s security system and is
therefore not responsible for and cannot guarantee the performance of the end user’s security
system which uses the Product or which the Product is a component of.
This Limited Warranty applies only to Products manufactured by or for RISCO. Further, this
Limited Warranty does not apply to any software (including operating system) added to or
provided with the Products or any third-party software, even if packaged or sold with the RISCO
Product. Manufacturers, suppliers, or third parties other than RISCO may provide their own
warranties, but RISCO, to the extent permitted by law and except as otherwise specifically set
forth herein, provides its Products “AS IS”. Software and applications distributed or made
available by RISCO in conjunction with the Product (with or without the RISCO brand),
including, but not limited to system software, as well as P2P services or any other service
made available by RISCO in relation to the Product, are not covered under this Limited
Warranty. Refer to the Terms of Service at:
https://riscocloud.com/ELAS/WebUI/UserLogin/License for details of your rights and
obligations with respect to the use of such applications, software or any service. RISCO does
not represent that the Product may not be compromised or circumvented; that the Product will
prevent any personal injury or property loss by burglary, robbery, fire or otherwise, or that the
Product will in all cases provide adequate warning or protection. A properly installed and
maintained alarm may only reduce the risk of a burglary, robbery or fire without warning, but it
is not insurance or a guarantee that such will not occur or will not cause or lead to personal
injury or property loss. CONSEQUENTLY, RISCO SHALL HAVE NO LIABILITY FOR ANY
PERSONAL INJURY, PROPERTY DAMAGE OR OTHER LOSS BASED ON ANY CLAIM AT
ALL INCLUDING A CLAIM THAT THE PRODUCT FAILED TO GIVE WARNING.
EXCEPT FOR THE WARRANTIES SET FORTH HEREIN, RISCO AND ITS LICENSORS
HEREBY DISCLAIM ALL EXPRESS, IMPLIED OR STATUTORY, REPRESENTATIONS,
WARRANTIES, GUARANTEES, AND CONDITIONS WITH REGARD TO THE PRODUCTS,
INCLUDING BUT NOT LIMITED TO ANY REPRESENTATIONS, WARRANTIES,
GUARANTEES, AND CONDITIONS OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, TITLE AND WARRANTIES AGAINST HIDDEN OR LATENT
DEFECTS, TO THE EXTENT PERMITTED BY LAW. WITHOUT LIMITING THE
GENERALITY OF THE FOREGOING, RISCO AND ITS LICENSORS DO NOT REPRESENT
OR WARRANT THAT: (I) THE OPERATION OR USE OF THE PRODUCT WILL BE TIMELY,
SECURE, UNINTERRUPTED OR ERROR-FREE; (ii) THAT ANY FILES, CONTENT OR
INFORMATION OF ANY KIND THAT MAY BE ACCESSED THROUGH THE PRODUCT
SHALL REMAIN SECURED OR NON DAMAGED. CUSTOMER ACKNOWLEDGES THAT
NEITHER RISCO NOR ITS LICENSORS CONTROL THE TRANSFER OF DATA OVER
COMMUNICATIONS FACILITIES, INCLUDING THE INTERNET, GSM OR OTHER MEANS
OF COMMUNICATIONS AND THAT RISCO’S PRODUCTS, MAY BE SUBJECT TO
LIMITATIONS, DELAYS, AND OTHER PROBLEMS INHERENT IN THE USE OF SUCH
MEANS OF COMMUNICATIONS. RISCO IS NOT RESPONSIBLE FOR ANY DELAYS,
DELIVERY FAILURES, OR OTHER DAMAGE RESULTING FROM SUCH PROBLEMS.
RISCO WARRANTS THAT ITS PRODUCTS DO NOT, TO THE BEST OF ITS KNOWLEDGE,
INFRINGE UPON ANY PATENT, COPYRIGHT, TRADEMARK, TRADE SECRET OR
OTHER INTELLECTUAL PROPERTY RIGHT IN ANY EVENT RISCO SHALL NOT BE
LIABLE FOR ANY AMOUNTS REPRESENTING LOST REVENUES OR PROFITS,
PUNITIVE DAMAGES, OR FOR ANY OTHER INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES, EVEN IF THEY WERE FORESEEABLE OR RISCO HAS
BEEN INFORMED OF THEIR POTENTIAL.
WARNING: This product should be tested at least once a week.
FCC ID: JE4RWX73F915
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Changes or modifications to this equipment which are not expressly approved by the
party responsible for compliance (RISCO Group's.) could void the user's authority to
operate the equipment.
FCC Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment on and off, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on to a different circuit from that to which
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this equipment which are not expressly approved by the
party responsible for compliance (RISCO Group's.) could void the user's authority to
operate the equipment.
© RISCO Group 03/17 5IN2579