Risco Agility Wireless I/O & X10 Module User manual

Page1
Introduction
RISCOGroupʹs2‐WayWirelessI/O&X10Moduleisanextensionmoduleenablingwired
devicestobeconnectedtotheAgilityWirelesssystem.
TheWirelessI/OModulesupports4hardwiredzones,4outputsandcontrolsupto16X10
devices.
EachoutputorX10devicecanbeoperatedinaresponsetoawidevarietyofsystemevents.
FordetailedinformationregardingtheprogrammingoptionsoftheWirelessI/OModule
refertotheinstallationmanualsoftheAgility.
Main Features
Bi‐directionalwirelesscommunication
2RelayOutputs(3Amp)
2TransistorOutputs(500mA)
4Inputs(NO,NC,EOL)
Fullysupervised
Dualtamperprotection(Box&Wall)
X10adapter,upto16X10devices
Wireless I/O Module - Main Components
1. RFModule
2. InputTerminals
3. RelayOutputTerminals
4. TransistorOutputterminals
5. ACPowerterminals
(parallelconnectiontoJ2)
6. Back/Walltamper(notvisible)
7. J2Powersocket
8. 3LEDindication
9. RJ11connector(X10connection)
10. Boxtamperswitch
11. Batteryholders
RF Module
2
13 4 5
8
9
7
11
6
10
X10
Z33 COM Z34 Z35 COM Z36 NO U01 NC NO U02 NC U03 COM U04 AC
CC
Figure1:WirelessI/OModuleMainComponents

Page2
LED Indications
LEDStateDescription
OnACandbatteriesOK
FlashingACtroubleorLowbattery(below3.1VDC)
(Red) Power
OffPowernotpresent
OnX10ConnectedtotheWirelessI/OModule
(Yellow) X10
OffX10Disconnected
OnTheI/OexpanderiscommunicatingwiththeAgility
(Green)Communication
OffNocommunicationistakingplace
Mounting the Wireless I/O Module
SelectamountinglocationnearanACpowersupplyinproximitytotheAgilitymainpanel
1. Openthecoverbytwistingascrewdriverintheslotsonthebottomortopofthecase
(Figure2).
Figure2:OpeningtheCover
2. Removethecircuitboard(Figure3)andopenknockoutsfortheentryofthepowerwires
(1,Figure4)andforthebacktamper(2,Figure4).

Page3
3. Mountthereceiveronthewallusingtheinstallationholes(3,Figure4)andreinstallthe
circuitboard.Makesurethatthatyouhearaʺclickʺwhenattachingthetamperspringto
thewall.
Z33 COM Z34Z35 COM Z36 NO
UO1
CNC NO
UO2
CNC UO3 COM UO4 AC
Figure3:CircuitBoardRemoval
1
1
2
3
Figure4:KnockoutsandInstallationHoles
4. ConnectthepowersourcewireplugtotheJ2powerjackonthePCBortotheAC
terminalsonthePCB.Thepolarityisnotimportant.DoNotplugthetransformerintothe
walloutletatthispoint.
5. Pluginthe threerechargeablebatteries(sizeAANiMH 2300mAH)intothebattery
holders.Payattentiontothecorrectpolarity(+)(‐).

NOTE:
Rechargeable batteries should be charged for at least 24 hours.

IMPORTANT:
When replacing the batteries be sure to use the same type. Failure to comply with this
instruction may result in damage to personnel and/or equipment. Dispose of used batteries
according to local regulations.
6. Setallinputsandoutputwiring,asdescribedbelow.


Page4
Wiring the Wireless I/O module
Inputswiring
TheAgilitysupports4hardwirezones(definedintheAgilitysystemaszones33‐36)thatcan
bedefinedasNormallyOpen,NormallyClosedorEndofLineZones.
Thefollowingdiagramillustratesthevariouszoneconnections:
END OF LINE ZONE
(N.O CONTACT)
ALARM
2.2 K
NORMALLY OPEN ZONE
CONFIGURATION
ALARM
NORMALLY CLOSED
ZONE CONFIGURATION
ALARM
END OF LINE ZONE
(N.C CONTACT)
2.2 K
ALARM
Z COM Z COM
DEVICE DEVICE DEVICE DEVICE
ZCOM Z COM

UtilityOutputswiring
TheAgilityincludes4utilityoutputs(2x24VDC3Amprelaysand2x13.8VDC500mA
transistoroutputs).Theseoutputscanoperateexternaldevicesinresponsetoanumberof
systemactivities.Fordetailedinformationregardingtheprogrammingoftheutilityoutputs
refertotheAgilityInstallerGuide.
TowireRelayOutputs(UO1,UO2)
Wirethedevicesthatyouwanttoactivatetotheoutputs,asfollows:
NOTE:
UO1 and UO2 connections are identical.





NC:Normallyclosedcontact
C:Commoncontact
NO:Normallyopencontact
UO1/UO2behaveasdrycontacts

Page5
TowireTransistorOutputs(UO3‐UO4)
ConnectthedevicebetweenthepositiveconnectionoftheexternalpowerandtheUO3or
UO4(+).ConnectthenegativeconnectionoftheexternalpowertotheCOM(‐)terminal.
X10 Connection
ThewirelessI/OexpanderenablestheAgilitytocontrolX10devices.TheI/Oexpander
convertstheinformationsentfromtheprogrammableutilityoutputintotheX10protocol.Up
tosixteenX10devicescanbeactivated.Thesearerecognizedinthesystemasoutputs5to20.
ToconnecttheX10
ConnecttheX10controllercabletotheRJ11connectorlocatedontheWirelessI/Omodule
PCB.
Transmitter/Receiver Communication Setup
Tosetupthecommunicationwiththereceiver,theI/Oexpandershouldidentifyitselftothe
systemʹsreceiverinthesamewayassettingcommunicationtoawirelesszone.
1. SetthesecuritypaneltoLearnmode.
2. SendaWRITEmessagewithin15secondsafterI/Oexpanderpowerup,bypressingthe
WallandCovertampersswitchessimultaneouslyforatleast3seconds(whenthePCBIS
installedONLYthecovertamperhastobepressed).
3. VerifythattheI/Oexpanderhasbeenidentifiedbythesecuritypanel.
4. InstalltheWirelessI/OModulefrontcoverbackinitsplace.Lockscrewlocatedatthe
topoftheunit.
Programming
ChangingDefaultSettings
ViatheAgilitypanelyoucandefinetheInputs,OutputsandX10parameterssettings
accordingtoyourrequirements.
FormoreinformationrefertotheAgilityInstallerManual.
IMPORTANT:
Before proceeding with the steps below, plug the AC transformer into the wall outlet.

Page6
Diagnostics
YoucanperformdiagnostictestsandcheckthestatusoftheInputs,Outputsconnectedtothe
WirelessI/OModuleandthecommunicationbetweenthemoduleandtheAgility.The
diagnosticscanbeperformedlocallyfromakeypadorremotelyfromtheConfiguration
Software.
Technical Specifications
ElectricalCharacteristics
PowerSupply
CurrentConsumption
BackupBatteries
RelayOutputs
TransistorOutputs
OperatingTemperature
StorageTemperature
14.4VDC/1.5A
or
9VAC/1.5A (Preferred)
0.35Amaximum
3xsizeAANiMHcylindricalcell1.2V2300mAH
2x3Amps24VDCprogrammable
2x500mAtransistors(OpenCollector)
‐10°Cto40°C(32°Fto131°F)
‐20°Cto60°C(‐4°Fto140°F)
PhysicalCharacteristics
Dimension14.5cmx9.0cmx4.0cm(5.7x3.54x1.57inch)
Weight(withbatteries)0.24Kg(0.52lb)
WirelessCharacteristics
RFimmunity
Frequency
AccordingtoEN50130‐4
433.92MHz
Compliance
EN50131‐1,EN50131‐3Grade2
EN50130‐5EnvironmentalclassII
EN50131‐6TypeA
Ordering Information
ModelDescription
RW132IO40AUH RISCO Agility Wireless I/O Module
CAUTION:Riskofexplosionifbatteryisreplacedbyanincorrecttype.Disposeofused
batteriesaccordingtolocalregulations.

FCC Note
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBdigitaldevice,
pursuanttoPart15oftheFCCrules.Theselimitsaredesignedtoprovidereasonableprotection
againstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,usesandcan
radiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,may
causeharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterference
willnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradio
ortelevisionreception,whichcanbedeterminedbyturningtheequipmentoffandon,theuseris
encouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:
a) Reorientorrelocatethereceivingantenna.
b) Increasetheseparationbetweentheequipmentandreceiver.
c) Connecttheequipmenttoanoutletonacircuitdifferentfromthattowhichthe
Receiverisconnected.
d) Consultthedealeroranexperiencedradio/TVtechnician.
FCCID:JE4AGILITY
IC:6564A‐AGILITY
FCC Warning
ThemanufacturerisnotresponsibleforanyradioorTVinterferencecausedbyunauthorized
modificationstothisequipment.Suchmodificationscouldvoidtheuserʹsauthoritytooperatethe
equipment.
RISCO Group Limited Warranty
RISCOGroupanditssubsidiariesandaffiliates(ʺSellerʺ)warrantsitsproductstobefreefromdefectsin
materialsandworkmanshipundernormalusefor24monthsfromthedateofproduction.BecauseSellerdoes
notinstallorconnecttheproductandbecausetheproductmaybeusedinconjunctionwithproductsnot
manufacturedbytheSeller,Sellercannotguaranteetheperformanceofthesecuritysystemwhichusesthis
product.Sellersʹobligationandliabilityunderthiswarrantyisexpresslylimitedtorepairingandreplacing,at
Sellersoption,withinareasonabletimeafterthedateofdelivery,anyproductnotmeetingthespecifications.
Sellermakesnootherwarranty,expressedorimplied,andmakesnowarrantyofmerchantabilityoroffitness
foranyparticularpurpose.Innocaseshallsellerbeliableforanyconsequentialorincidentaldamagesfor
breachofthisoranyotherwarranty,expressedorimplied,oruponanyotherbasisofliabilitywhatsoever.
Sellersobligationunderthiswarrantyshallnotincludeanytransportationchargesorcostsofinstallationorany
liabilityfordirect,indirect,ornotbecompromisedorcircumvented;thattheproductwillpreventanypersona;
injuryorpropertylossbyintruder,robbery,fireorotherwise;orthattheproductwillinallcasesprovide
adequatewarningorprotection.Buyerunderstandsthataproperlyinstalledandmaintainedalarmmayonly
reducetheriskofintruder,robberyorfirewithoutwarning,butisnotinsuranceoraguarantythatsuchwillnot
occurorthattherewillbenopersonalinjuryorpropertylossasaresult.Consequentlysellershallhaveno
liabilityforanypersonalinjury,propertydamageorlossbasedonaclaimthattheproductfailstogivewarning.
However,ifsellerisheldliable,whetherdirectlyorindirectly,foranylossordamagearisingfromunderthis
limitedwarrantyorotherwise,regardlessofcauseororigin,sellersmaximumliabilityshallnotexceedthe
purchasepriceoftheproduct,whichshallbecompleteandexclusiveremedyagainstseller.Noemployeeor
representativeofSellerisauthorizedtochangethiswarrantyinanywayorgrantanyotherwarranty.
WARNING:Thisproductshouldbetestedatleastonceaweek.

RTTE Compliance Statement
Hereby,RISCOGroupdeclaresthatthisequipmentisincompliancewiththeessential
requirementsandotherrelevantprovisionsofDirective1999/5/EC.FortheCEDeclarationof
Conformitypleaserefertoourwebsite:www.riscogroup.com.
Contacting RISCO Group
RISCOGroupiscommittedtocustomerserviceandproductsupport.Youcancontactus
throughourwebsitewww.riscogroup.comorasfollows:
UnitedKingdom
Tel:+44‐161‐655‐5500
[email protected]
USA
Tel:+1‐631‐719‐4400
support‐[email protected]
Italy
Tel:+39‐02‐66590054
[email protected]
Brazil
Tel:+1‐866‐969‐5111
support‐[email protected]
Spain
Tel:+34‐91‐490‐2133
support‐[email protected]
China
Tel:+86‐21‐52390066
support‐[email protected]
France
Tel:+33‐164‐73‐28‐50
support‐[email protected]
Poland
Tel:+48‐22‐500‐28‐40
support‐[email protected]
Belgium
Tel:+32‐25227622
support‐[e-mail]
Israel
Tel:+972‐(0)3‐963‐7777
[email protected]
Allrightsreserved.
Nopartofthisdocumentmaybereproducedinanyformwithoutpriorwrittenpermission
fromthepublisher.
©RISCOGroup01/10 5IN1038E