Riton 1 TACTIX User manual

1 TACTIX
ARD RED DOT

2
TABLE OF CONTENTS
3 OPTIC SPECIFICS
4 TECHNICAL SPECIFICATIONS
5 EXPLANATION OF MOA
5 ILLUMINATION SYSTEM
6 MOUNTING THE RITON OPTIC
7 BORE SIGHTING
7 ZEROING THE RED DOT
8 TROUBLESHOOTING
8 WARRANTY
THANK YOU FOR
CHOOSING RITON
OPTICS.
We know that you have many
options and we are thankful for
selecting Riton as your optics
provider.
As a company founded by Law Enforcement and Military Veterans,
we take our commitment to service seriously. We have an
unwavering passion for offering high quality optics at the industry’s
most competitive prices and matched by incredible service. You
will see the difference in everything we do because we are different,
and we developed this company to be exactly that so that you, the
consumer, get everything you deserve. If you are ever in need of
additional information or assistance, please contact us. We are here
to continually serve you as a valued partner.
“RITON WAS BUILT OUT OF THE BELIEF THAT
A PERSON’S HARD-EARNED DOLLAR SHOULD
BUY QUALITY OPTICS AND THE BEST SERVICE
AT EVERY PRICE POINT.”
FOUNDER & CEO
Founder and CEO
BRADY SPETH - FOUNDER AND CEO
Brady Speth - Founder and CEO
BRADY SPETH BRADY SPETH
FOUNDER AND CEO
Founder and CEO

3
1 TACTIX ARD
OPTIC SPECIFICS
The 1 Tactix ARD is one of Riton’s most versatile red dots, whether you’re mounting it to an
AR, AK, a shotgun, or a pistol. Featuring the Riton 2 MOA ultra-precise red dot, it comes with a
lower 1/3 co-witness QD mount and a ush mount for the perfect mounting height no matter
the platform.
DETAILED PRODUCT
FEATURES:
/1 MOA Windage and Elevation Adjustment
/ 6 levels of red illumination featuring on/off
between each level
/ 40,000 Hours Battery Life
/ Assembled in EP-Level Clean Room
/ 100% Waterproof, Fog Proof and Shockproof
(tested up to 1200 G’s)
1/3CO WITNESSQD MOUNT
OBJECTIVE
WINDAGE
ELEVATION
ILLUMINATION

4
MAGNIFICATION: 1
PARALLAX ADJUSTMENT: Fixed at 50 yards
OBJECTIVE LENS DIAMETER: 23mm
LENS COATING: Fully Multi-Coated, Full Wide Band, Waterproof
Coated, Low Light Enhancement
DOT SIZE: 2 MOA
MATERIAL: 6061-T6 Aircraft Grade Aluminum
EYE RELIEF: Unlimited
CLICK VALUE AT 100 YDS/MM: 1 MOA
ADJUSTMENT RANGE: 120 MOA
LENGTH: 2.48in/63mm
WEIGHT: 3.5oz/100g
TECHNICAL SPECIFICATIONS

5
ADJUSTING YOUR RED DOT
Use the chart’s below to determine the clicks needed to adjust your point of
impact.
For more information on MOA and MRAD,
scan the QR code above for an in depth
video from Riton University
EXPLANATION OF MINUTE OF ANGLE (MOA)
MOA unit of arc measurements are based on degrees and minutes. There
are 360 degrees in a circle and 60 minutes in a degree for a total of 21,600
minutes (MOA) in a circle. A minute of angle will subtend 1.05 inches at a
distance of 100 yards.
*Graduations can be calculated at additional distances beyond 200 yds.
.25 IN .50 IN 1 IN 1.5 IN 2 IN
25 YARDS 50 YARDS 100 YARDS 150 YARDS 200 YARDS
BASED ON 1 MOA ADJUSTMENTS
ILLUMINATION SYSTEM
The variable intensity reticle illumination system aids in low light
situations.
TO ACTIVATE THE ILLUMINATION:
Rotate the adjustment knob in either direction. There are six levels of
brightness with off positons between each brightness setting.
TO CHANGE THE BATTERY
Unscrew the outer cap located on the illumination/parallax knob, then
replace with a new CR2032 Battery.

6
MOUNTING YOUR RITON RED DOT
TO MOUNT YOUR RITON RED DOT:
1. Place the red dot on the picatinny rail of your weapon.
2. Before tightening the QD Mount, adjust for maximum eye
relief to avoid injury from recoil.
3. Tighten the lever on the QD Mount.
For more information on Mounting, scan the
QR code above for an in depth video from Riton
University

7
BORE SIGHTING
Bore sighting is a preliminary procedure to achieve proper alignment of the
scope with the rie’s bore. Initial bore sighting of the red dot will decrease
the amount of time and ammunition you need to use at the range.
This can be done by using a mechanical or laser bore sighter according
to the manufacturer’s instructions or by removing the bolt and sighting
through the barrel on some ries.
TO BORE SIGHT YOUR RED DOT:
1. Place the rie solidly on a rest and remove the bolt or bolt
carrier group.
2. Sight through the bore at a target approximately 50 yards
away.
3. Move the rie and the rest until the target is visually centered
inside the barrel.
4. With the target centered in the bore, make windage and
elevation adjustments until the dot is also centered over the
target.
Note - If a laser bore sighting or any other similar device inside the bore
was used, it must be removed before ring. An obstructed bore can cause
serious damage to the gun and possible injury to the shooter.
ZEROING THE RED DOT
IMPORTANT SAFETY CHECKS:
• Always check your weapon and surroundings for safety.
• Follow all weapon manufacturer safety guidelines.
• Always shoot from a solid rest using consistent and proper form.
• Be sure that your target is level to aid in accurate sight-in process.
TO ZERO THE RED DOT:
1. Start the sight-in process from 25 yards. From a solid rest
re one 3-shot group, ensuring that you re at same spot
each time.
2. After the rst 3-shot group, make adjustments to bring bullet
impact to the center of target you’re shooting at. Repeat this
process at 100 yards and you will have an accurate 100 yard
zero.
For more information on Bore Sighting and Zeroing
your scope, scan the QR code above for an in depth
video from Riton University

8
1-855-39-RITON
[e-mail]
RITONOPTICS.COM
RITON PROMISE WARRANTY
As a part of the Riton Promise we believe in providing you with the best possible service, including the industry’s best warranty. The quality of
our products makes this the best warranty you’ll likely never have to use; however, as hunters and outdoorsmen and women, we know that bad
things sometimes happen to even the most cautious.
OUR WARRANTY IS SIMPLE:
• No proof of purchase or registration required for your Riton products.
• Lifetime warranty regardless of original purchaser.
• All warranty replacements will receive a brand-new product off the shelf. We will not ever replace the product with a repaired or
refurbished product.
• Replacement product will be shipped within 48 hours of receiving and approving your return.
• Loss, theft and/or deliberately worn and damaged products are not covered. Warranty is VOID if damage results from unauthorized repair
or alteration.
TROUBLESHOOTING
Problems thought to be associated with your riescope are often actually mount problems. Take the time to ensure the mounts are tight to the
rie and that scope is secured and does not twist or move in the rings. Conrm that the correct base and rings are being used and that they are
in the proper orientation. Be sure to torque your rings per the manufacturer’s spec
Keep in mind there are many issues that can cause poor bullet grouping. Always utilize a solid rest and maintain good shooting technique.
Have a qualied gunsmith look over your rie to be sure all things are in working order. See that the action and barrel are properly cleaned.
Some ries and ammunition don’t work well together, try different ammunition and see if accuracy improves.