RKC INSTRUMENT SA100 Series Operating and maintenance instructions

Digital Temperature Controller SA100
General Description
SA100
Features
The SA100 is a socket mounting type temperature controller and is available for mounting inside panel by easily mounting on DIN rail. The
SA100 has features such as analog retransmission output, advanced self-tuning, alarms, digital communications for networking and digital
contact for SV1/SV2 or RUN/STOP functions..
Simple mounting on DIN Rail
Corresponding to various applications
Analog retransmission output
Digital communications
Advanced self-tuning
Simple Mounting on DIN Rail
The SA100 can be simply mounted on DIN rail with DIN rail
mounting socket. The maintenance is also simple, as the unit
can be removed from socket.
Corresponding to Various Applications
Two points of output can be used as control, alarm or analog
retransmission. The SA100 corresponds to various applications
such as temperature controller and overheat protection unit.
Analog Retransmission Output (Optional)
An analog output is available so that the process value can be
retransmitted an analog signal to a remote instrument such as a
recorder or data-logging equipment.
R
R
1SA100_01E
DIN rail mounting socket
PV
SV
SA100
SETR/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SETR/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SETR/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
• The rear terminal socket allows the unit to be mounted
on a panel board.
Rear terminal socket
OUT1 OUT1
OUT2
OUT1
OUT2
OUT1
OUT2
Control output
Control output
Alarm output
Alarm output
Alarm output
Heating output
Cooling output
Retransmission
output Retransmission output
• As a temperature controller
• As a overheat protection unit
or alarm unit
1. Temperature alarm controller
3.Heat/Cool temperature controller
2.Temperature retransmitting controller
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
Control output
Control output
1. Overheat protection unit
3. Alarm unit
2. Overheat protection unit with transmitting
function
* Setting to ON/OFF action by
specifying direct action.
* Setting to ON/OFF action by
specifying direct action.
OUT1
OUT2
OUT1
OUT2
PV
SV
SA100
SET R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SETR/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
• The change of display for PV/SV can be configurable.
For the details of it, contact our sales office.
PV (measured value)
display only
SV (set value)
display only
The SV is displayed on PV display.
Parameters are displayed on SV
display.
100.0°C
Analog output
4 to 20 mA DC or
0 to 20 mA DC
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
(800) 576 - 6308
www.rkc-usa.com
Distributed By Inc,
RKC

Digital Temperature Controller SA100
Features
Alarms (Optional)
Two alarm points can be configured for specific applications.
Digital Contact Input for External
Switching (Optional)
An optional digital contact input is available for RUN/STOP and
SV1/SV2 switching. (RUN/STOP switching can also be
completed at the front key panel.) This function can be used
with the output from a timer, PLC, etc. When the
communication feature is selected, the external contact input is
not available.
Heat/Cool Control (Optional)
The Heat/Cool PID control features heat and cool outputs for
use where process-generated heat exists. This allows the input
of overlap or deadband settings which contribute to energy
savings.
2SA100_01E
Heat
output Cool output
0%
100%
Set value
Deadband
Heat
output Cool output
0%
100%
Set value
Overlap
Alarm Type
• Temperature Alarm
Deviation High, Deviation Low, Deviation High/Low, Band,
Process High, Process Low
(Hold action can be added to deviation and process type)
• Set Value Alarm
High, Low
• Loop Break Alarm
Temperature Alarm
Set Value Alarm
Deviation High (Alarm Set Value is a positive (+) setting)
(Alarm Set Value is a negative (-) setting)
(Alarm Set Value is the absolute deviation value)
(Alarm Set Value is the absolute deviation value)
Deviation Low
OFF
OFF
ON
ON
Deviation
High/Low OFF
ON ON
Band OFF OFF
ON
Process High
Process Low
OFF
OFF
ON
ON
Set Value High
Set Value Low
OFF
OFF
ON
ON
: SV : Alarm
: SV
The SA100 offers an optional RS-485 communications
interface for networking to computers, PLCs and SCADA
software. MODBUS or ANSI protocol can be selected. Up to
32 units, including host computer, can be multi-dropped on one
RS-485 communication line. When the communication feature
is selected, the external contact input is not available.
Digital Communications (Optional)
RS-485 Communication
level converter
Up to 31 units
A
62P
A
3
N
CPU
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
PV
SV
SA100
SET
R/S
AT
OUT1
OUT2
ALM1
SV2
ALM2
Contact:ON Contact:OFF
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
PV
SV
SA100
AT
OUT1
OUT2
SV2
ALM1
ALM2
• RUN/STOP • SV1/SV2
Instrument operating
(RUN mode)
Down for maintenance
(STOP mode)
Machine production
in full operation (SV1)
Machine production
suspended (SV2)
Contact:OFF Contact:ON
The SA100 offers a new self-tuning feature that is initiated at
start-up and when process parameters or conditions change. In
these situations, the controller evaluates whether the preset PID
parameters should be maintained or replaced by the latest self-
tuning parameters to achieve the best control for the process.
Self-tuning can be manually turned ON/OFF in the parameter
setting mode. This feature is not available with the Heat/Cool
control.
In addition to self-tuning, The SA200 has standard autotuning
(AT) so that either function can be selected to achieve optimum
process control.
Self-Tuning Algorithm
When overshoot
occurs, self-tuning
is initiated
At start-up or set value change
At set value change
When control is stable,
self-tuning is not initiated
When control is stable,
self-tuning is not initiated
When control is stable,
self-tuning is not initiated
Oscillation
Temp
Time
When undershoot
occurs, self-tuning
is initiated
When control
disturbance occurs,
self-tuning is initiated

Specifications
Input
Alarms (Up to 2 points) (Optional)
Performance
Control
General Specifications
Input
 a) Thermocouple :  K, J, E, T, R, S, B, N (JIS/IEC), PLII (NBS)
    W5Re/W26Re(ASTM), U, L (DIN)
  •Input impedance :Approx.1MΩ
  •Influence of external resistance : Approx.0.2µV/Ω
  •Input break action : Up-scale
 b) RTD : Pt100(JIS/IEC), JPt100(JIS)
  •Influence of lead resistance : Approx.0.01[%/Ω] of reading
  •Maximum 10Ωper wire
  •Input break action : Up-scale
  •Input short action : Down-scale
 c) DC voltage : 0 to 5V DC, 1 to 5V DC, 0 to 10V DC
 d) DC current : 0 to 20mA DC, 4 to 20mA DC
  • For DC current input, connect a 250 Ωresister to the input terminals.
  •Refer to the Input and Range and Input Code Table for details.
  •Input break action : Down-scale
  •Both Heat/Cool control outputs are OFF for Heat/Cool PID action.
  •Reading is around zero for 0 to 5V DC input, 0 to 10V DC input 
  and 0 to 20mA DC input.

SamplingTime
 0.5 sec.
PV Bias
 - span to +span (Within -1999 to 9999)
Measuring Accuracy
 a) Thermocouple
  ±(1% of reading + 1 digit) or ±2°C (4°F) whichever is larger
  •Accuracy is not guaranteed between 0 and 399°C (0 and 799°F)
  for type R, S and B.
  •Accuracy is not guaranteed less than -100.0°C (-158.0°F) for
  type T and U.
 b) RTD
  ±(0.3% of reading + 1 digit) or ±0.8°C (1.6°F) whichever is larger
 c) DC voltage and DC current
  ±(0.3% of span + 1 digit) 

Insulation Resistance
 More than 20MΩ(500V DC) between measured terminals and ground
 More than 20MΩ(500V DC) between power terminals and ground
Dielectric Strength
 1000V AC for one minute between measured terminals and ground
 1500V AC for one minute between power terminals and ground
Control Method
 a) PID control (with autotuning and self-tuning function)
•Available for reverse and direct action.(Specify when ordering.)
•ON/OFF, P, PI and PD control are also selectable.
  ON/OFF action differential gap :2°C(°F) (Temperature input)
   0.2% (Voltage, current input)
 b) Heat/Cool PID control (with autotuning function)
•A ir cooling and water cooling type are available. (Specify when ordering.)
Major Setting Range
 Set value : Same as input range.
 Heat side proportional band : 1 to span or 0.1 to span
  (ON/OFF action when P=0)
 Cool side proportional band : 0 to 1000% of heat side proportional band
 Integral time : 0 to 3600sec.(PD action when I=0)
 Derivative time : 0 to 3600sec.(PI action when D=0)
 Anti-Reset Windup(ARW) :1 to 100% of heat side proportional band
  (Integral action is OFF when ARW=0)
 Proportional cycle time : 1 to 100 sec.
 Deadband/Overlap : -span to +span (Within -1999 to 9999)
Outputs
Output
 Can be set for control, alarm or retransmission functions.
•Alarm output can be set for energized/de-energized action.
•Alarm output can be set for AND/OR logic calculation.
 Number of outputs : 2 points
OutputType
 Relay contact output : 250V AC 2A (resistive load), Form C contact
 Voltage pulse output : 0/12V DC (Load resistance : more than 600Ω)
 •Measurement terminals and output terminal are not isolated.
Current output : 0 to 20mA, 4 to 20mA DC
(Load resistance : less than 400 Ω)
•Measurement terminals and output terminal are not isolated.
AlarmType
 Deviation High, Deviation Low, Deviation High-Low, Deviation Band
 P rocess High, Process Low, Set value High, Set value Low
 Loop break alarm(LBA)
Setting Range
 a) Deviation alarm : - span to +span (Within - 1999 to 9999)
 b) Process alarm : Same as set value (SV).
 c) Set value alarm : Same as set value (SV).
 d) Loop break alarm : 0.0 to 200.0 min.
Differential Gap
 2°C (°F) or 2.0°C (°F) (Temperature input) , 0.2% (Voltage, current input)
Communications  (Optional)
Waterproof/Dustproof  (Optional)
Compliance with Standards
 a) Communication method : Based on RS-485 (2-wire)
 b) Communication speed : 2400, 4800, 9600, 19200 BPS
 c)Protocol : ANSI X3.28(1976) 2.5 A4
    MODBUS
 d)Bit format
   Start bit : 1
   Data bit : 7 or 8 •For MODBUS 8 bit only
   Parity bit : Without, Odd or Even
   Stop bit : 1 or 2
 e)Communication code : ASCII(JIS) 7-bit code
f) Maximum connection : 31 ( Address can be set from 0 to 99.)
Retransmission Output  (Optional)
Retransmission output is allocated to OUT1.
 a)Type : Process value, Set value, Deviation,
Manipulated value
 b)Output type : 0 to 20mA DC, 4 to 20mA DC
(Load resistance : less than 400 Ω)
c)Output resolution : More than 10bits
•Measurement terminals and output terminal are not isolated.
Dustproof and waterproof protection : IP66
•Waterproof/dustproof protection only effective from the front in panel
mounted installations.
Contact Input  (Optional)
Number of Inputs : 2 points
Contact InputType
 a) RUN/STOP switching (OPEN : STOP, CLOSE : RUN)
 b) STEP function (OPEN : SV1, CLOSE : SV2)
Input Rating
 Non-voltage contact input. (OPEN : 500kΩor more, CLOSE : 10Ωor less)
• CE Mark
•UL Recognized
•CSA Certified
•C-Tick Mark
SupplyVoltage
 a) 85 to 264V AC (Including supply voltage variation)
  [Rating : 100 to 240V AC] (50/60Hz common)
 b) 21.6 to 26.4V AC(Including supply voltage variation)
  [Rating : 24V AC] (50/60Hz common)
 c) 21.6 to 26.4V DC(Ripple rate 10% p-p or less)
  [Rating : 24V DC]
Power Consumption
 Less than 4VA (at 100V AC), 7VA (at 240V AC) for standard AC type
 Less than 4VA for 24V AC type
 Less than 100mA for 24V DC type
Power Failure Effect
 A power failure of 20 ms or less will not affect the control action.
 If power failure of more than 20 ms occurs, controller will restart.
Operating Environments : 0 to 50°C [32 to 122°F] , 45 to 85% RH
Memory Backup : Backed up by non-volatile memory.
Number of writing : Approx. 100,000 times
NetWeight : Approx. 120g
External Dimensions (W x H x D) :48 x 48 x 70mm (1/16 DIN)
Digital Temperature Controller SA100
R
R
3SA100_01E

Digital Temperature Controller SA100
Model and Suffix Code
Model
Control method
Input and Range
Power supply voltage
Alarm 1
Alarm 2
Communication
Contact input
Waterproof/Dustproof
Output allocation code 1
Instrument version
OUT 1
(Control, alarm or
retransmission output)
OUT 2
(Control or alarm output)
Specifications Model and Suffix Code
PID control with AT (reverse action)
SA100 (1/16 DIN size, socket mounting type) F
D
W
A
N
5
6
DN
1No code
M
M
N
3
N
4
V
7
8
V
PID control with AT (direct action)
Heat/cool PID control with AT (water cooling)
Heat/cool PID control with AT (air cooling)
See Range and Input Code Table
Relay contact output
Voltage pulse output
DC current output : 0 to 20mA
DC current output : 4 to 20mA
No output
24V AC/DC
100 to 240V AC
No alarm
See Alarm Code Table
No alarm
See Alarm Code Table
Not supplied
Digital communications : RS-485 (RKC standard)
Digital communications : RS-485 (MODBUS)
External contact input
Not supplied
Waterproof/Dustproof protection
Standard output
See Output Allocation Code Table
Version symbol
Relay contact output
Voltage pulse output
N
Y
Y
1 When standard output is selected with control method F or D, Out 1 will always be the control output and Out 2 will either be unused, Alarm 1 or OR logic output of Alarm 1 and Alarm 2.
 Standard output is automatically selected with control method W or A. Out 1 will become heat-side control output and Out 2 will be cool-side control output.
Range and Input Code Table
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
0 200°C
0 400°C
0 600°C
0 800°C
0 1000°C
0 1200°C
0 1372°C
0 100°C
0 300°C
0 500°C
0 450°C
-199.9 300.0°C
0.0 400.0°C
0.0 800.0°C
0.0 200.0°C
0.0 600.0°C
-199.9 800.0°C
0 800°F
0 1600°F
0 2502°F
20 70°F
0.0 800.0°F
-199.9 999.9°F
0 200°C
0 400°C
0 600°C
0 800°C
0 1000°C
0 1200°C
0 450°C
-199.9 300.0°C
0.0 400.0°C
0.0 800.0°C
0.0 200.0°C
0.0 600.0°C
-199.9 600.0°C
0 800°F
0 1600°F
0 2192°F
0 400°F
0.0 800.0°F
-199.9 999.9°F
0 1600°C
0 1769°C
0 1350°C
0 3200°F
0 3216°F
RangeCodeInput
K 01
K 02
K 03
K 04
K 05
K 06
K 07
K 13
K 14
K 20
K 17
K 08
K 09
K 10
K 29
K 37
K 38
K A1
K A2
K A3
K A9
K A4
K B2
J 01
J 02
J 03
J 04
J 05
J 06
J 10
J 07
J 08
J 09
J 22
J 23
J 30
J A1
J A2
J A3
J A6
J B6
J A9
R 01
R 02
R 04
R A1
R A2
K
(JIS/IEC)
J
(JIS/IEC)
R
(JIS/IEC)
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
-199.9 649.0°C
-199.9 200.0°C
-100.0 50.0°C
-100.0 100.0°C
-100.0 200.0°C
0.0 50.0°C
0.0 100.0°C
0.0 200.0°C
0.0 300.0°C
0.0 500.0°C
-199.9 999.9°F
-199.9 400.0°F
-199.9 200.0°F
-100.0 100.0°F
-100.0 300.0°F
0.0 100.0°F
0.0 200.0°F
0.0 400.0°F
0.0 500.0°F
-199.9 649.0°C
-199.9 200.0°C
-100.0 50.0°C
-100.0 100.0°C
-100.0 200.0°C
0.0 50.0°C
0.0 100.0°C
0.0 200.0°C
0.0 300.0°C
0.0 500.0°C
RangeCodeInput
D 01
D 02
D 03
D 04
D 05
D 06
D 07
D 08
D 09
D 10
D A1
D A2
D A3
D A4
D A5
D A6
D A7
D A8
D A9
P 01
P 02
P 03
P 04
P 05
P 06
P 07
P 08
P 09
P 10
Pt100
(JIS/IEC)
JPt100
(JIS)
to
to
to
to
to
0.0 100.0%
0.0 100.0%
0.0 100.0%
0.0 100.0%
0.0 100.0%
RangeCodeInput
4 01
5 01
6 01
7 01
8
0 to 5V
0 to 10V
1 to 5V
0 to 20mA
4 to 20mA 01
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
to
0 1600°C
0 1769°C
0 3200°F
0 3216°F
400 1800°C
0 1820°C
800 3200°F
0 3308°F
0 800°C
0 1000°C
0 1600°F
0 1832°F
0 1200°C
0 1300°C
0.0 800.0°C
0 2300°F
0 2372°F
0.0 999.9°F
-199.9 400.0°C
-199.9 100.0°C
-100.0 200.0°C
0.0 350.0°C
-199.9 752.0°F
-100.0 200.0°F
-100.0 400.0°F
0.0 450.0°F
0.0 752.0°F
0 2000°C
0 2320°C
0 4000°F
0 1300°C
0 1390°C
0 1200°C
0 2400°F
0 2534°F
-199.9 600.0°C
-199.9 100.0°C
0.0 400.0°C
-199.9 999.9°F
-100.0 200.0°F
0.0 999.9°F
0 400°C
0 800°C
0 800°F
0 1600°F
RangeCodeInput
S 01
S 02
S A1
S A2
B 01
B 02
B A1
B A2
E 01
E 02
E A1
E A2
N 01
N 02
N 06
N A1
N A2
N A5
T 01
T 02
T 03
T 04
T A1
T A2
T A3
T A4
T A5
W 01
W 02
W A1
A 01
A 02
A 03
A A1
A A2
U 01
U 02
U 03
U A1
U A2
U A3
L 01
L 02
L A1
L A2
E
(JIS/IEC)
N
(JIS/IEC)
T
(JIS/IEC)
W5Re/W26Re
(ASTM)
S
(JIS/IEC)
B
(JIS/IEC)
PLII
(NBS)
L
(DIN)
U
(DIN)
Thermocouple input RTD input
Voltage/Current DC input
1Type R,S and B input : Accuracy is not guaranteed between 0 and 399°C (0 and 799°F).
2Type T and U input :Accuracy is not guaranteed less than -100.0°C (-158.0°F).
3DC current input : A 250 Ωresistor is externally connected at the input terminals.
1
1
2
2
1
4SA100_01E
3
(Field-programmable) (Field-programmable)
(Field-programmable)

Digital Temperature Controller SA100
Alarm Code Table
Output Allocation Code Table
Accessory
Code
0 3
0 4
0 5
0 6
0 7
0 8
0 9
1 0
1 1
1 2
1 3
1 4
1 5
1 6
PID control + Alarm 1
PID control + Alarm 1, 2
PID control + Alarm 1, 2
PID control + Alarm 1, 2
PID control + Alarm 1, 2 or only Alarm 1 1
1
2
2
2
PID control + Alarm 1, 2
Alarm 1 + Alarm 2
Alarm 1 + Alarm 2
Alarm 1 + Alarm 2
Control output
Control output
Control output
Control output
Control output
Control output
Alarm 1 output (Energized)
Alarm 1 output (Energized)
Alarm 1 output (De-energized)
Alarm 1 output (De-energized)
AND logic output of Alarm 1 and Alarm 2 (Energized)
OR logic output of Alarm 1 and Alarm 2 (De-energized)
AND logic output of Alarm 1 and Alarm 2 (De-energized)
No output
Only Alarm 1 output (Energized)
Alarm 2 output (Energized)
Retransmission + PID control
Retransmission + Alarm 1, 2
Retransmission + Alarm 1, 2
Retransmission + Alarm 1, 2
Retransmission + Alarm 1, 2
Retransmission output
Retransmission output
Retransmission output
Retransmission output
Retransmission output
Control output
OR logic output of Alarm 1 and Alarm 2 (Energized)
OR logic output of Alarm 1 and Alarm 2 (De-energized)
AND logic output of Alarm 1 and Alarm 2 (Energized)
AND logic output of Alarm 1 and Alarm 2 (De-energized)
1 7
1 8
1 9
Retransmission + Alarm 1
Retransmission + Alarm 1
Heat-Cool PID control
Retransmission output
Retransmission output
Cool output (DC current output)
Alarm 1 output (Energized)
Alarm 1 output (De-energized)
Heat output (Relay contact orVoltage pulse output)
Alarm 2 output (De-energized)
Alarm 2 output (De-energized)
Output 1
Specifications Output 2Control methods
A Deviation High Deviation Low
Deviation High with Hold Deviation Low with Hold
Process Low Process High with Hold
Set value High
Shunt resistor for DC current input
Name Model code
Terminal cover KD100-55 KSA200-56A
Set value Low
Deviation High/Low Deviation Band
Deviation High/Low with Hold Process High
Process Low with Hold Loop break alarm 1
B C D
E F G H
J K L R
V W
1Loop break alarm is not available with Heat/Cool PID control type.
1The alarm monitor can only be confirmed by front LCD display or serial communication.
2Specify control action F to use both outputs as alarms.
Model and Suffix Code
5SA100_01E
PID
OUT1 PID OUT1
ALM1
PID
OUT1
ALM1
ALM2
PID
PID
OUT1
OUT2
PID
OUT1
ALM1
ALM1
PID
OUT1 PID
OUT1 PID
OUT1
PID
OUT1
ALM1
ALM2
PID
OUT1
PID
OUT2
ALM1
ALM2
ALM1
ALM2
Retransmission
OUT1 ALM1
ALM2
No alarm Alarm ON Alarm OFF Alarm ON Alarm OFF
Alarm ON Alarm OFF Alarm ON Alarm OFF
Alarm ON Alarm OFF
Alarm ON Alarm OFF
Alarm ON Alarm OFF
Alarm ON Alarm OFF
"OR" logic
ALM1
ALM2 Alarm ON Alarm OFF
Alarm ON Alarm OFF Alarm ON Alarm OFF
Alarm ON Alarm OFF
Alarm ON Alarm OFF
"OR" logic
ALM1
ALM2
Output alarm 1 only
ALM1
ALM2
"AND" logic
"AND" logic
ALM1
ALM2
"AND" logic
Heat-side
Cool-side
Only display
Only display
ALM1
ALM2
"OR" logic Alarm ON Alarm OFF
Energized alarm
Alarm ON Alarm OFF
Energized alarm
Alarm ON Alarm OFF
Energized alarm
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Output 1
Output 2
Energized alarm De-energized alarm
De-energized alarm De-energized alarm
De-energized alarm
Energized alarm
De-energized alarm
Energized alarm Energized alarm
Energized alarm
De-energized alarm
Energized alarm
Energized alarm
Standard Code 0 3
Code 0 7
Code 1 0
Standard
Code 0 4 Code 0 7
Code 1 1
Standard
Code 0 5
Code 0 8
Standard
Code 0 6
PID
Output 1
Output 2
Code 1 2
Code 0 9
Note: Relay contact output :250V AC 2A (resistive load), Form A contact
Power supply OFF : Open
Retransmission
Output 1
Output 2
Code 1 3
ALM1
ALM2
"OR" logic
Retransmission
Output 1
Output 2
Code 1 4
Alarm ON Alarm OFF
De-energized alarm
Alarm ON Alarm OFF
De-energized alarm
Alarm ON Alarm OFF
De-energized alarm
ALM1
ALM2
Retransmission
Output 1
Output 2
Code 1 5
"AND" logic
ALM1
ALM2
Retransmission
Output 1
Output 2
Code 1 6
ALM1
Retransmission
Output 1
Output 2
Code 1 7
ALM1
Retransmission
Output 1
Output 2
Code 1 8
PID
PID
OUT1
OUT2
Heat-side
Cool-side
Output 1
Output 2
Code 1 9

Digital Temperature Controller SA100
External Dimensions and Rear Layout
6SA100_01E
• Panel thickness must be between 1-10mm.
• Mounting frame is optional.
Panel Cutout
25 0
+0.6
45
0
+0.6
45 25
25
44.8
8.1
48
48
82.5
80
70
25
44.8
LN
7 8 9 10 111 2 3 4 5 6
PIN
SG
DI1
DI2
T/R(A) T/R(B)
RS-485
456
7
89
11
21
310
AB
BNC
NO
CNC
NO
C
1 2 3 1 2 3
DI1:STEP, DI2:RUN/STOP
Thermocouple
RTD
Voltage / Current *
1
2
3
1
2
3
1
2
3
1
2
Relay contact
Voltage pulse
DC Current
1
2
3
Relay contact
Voltage pulse
1
2
100 to 240V AC
24V AC/DC
Power supply
Output 1 Output 2
Measured input
Communications
Contents
Contact inputs
*A 250Ωresistor is externally connected at the input terminals.
Communication function and contact input are optional.
Connect connector to bottom of instrument.
A connector and connector cable for connecting the
input block is necessary to be prepared by the customer.
Housing: XHP-3 (J.S.T. Mfg. Co., Ltd. product)
Recommended cable size: AWG30 to 22
+
-
+
-
+
-
+
-
+
-
+
-
DIN rail mounting socket type
Model : ATC180041 (Matsushita Denko product) Rear terminal socket type Model : AT78051 (Matsushita Denko product)
1 2
3
4
5678
9
10 11
70
70
35.3
30.550
4
2-ø4.5 2-ø4.5 Mounting hole
3 2 1 10 9
4 5 6 7 8
11
45 21
16
5
43.4
40
Screw hole dimension
for wall mounting
• Socket (Optional) External Dimensions
±0.2
Units : mm