Roberts RT200 User manual

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com

1 Set the Anti-skating control to zero, raise the Cueing lever and unclip the Tone-arm so that it
moves freely.
2 Hold the Head-shell.It is currently
unbalanced and will drift upwards.
3 Rotate the Counterweight so that
it moves further onto the Tone-arm.
4 Check the balance and lower the
Cueing lever to see if the tone-arm
falls, rises or remains level.
5 Adjust the Counterweight so that it
moves in or out until the Tone-arm
is balanced and remains level when
the cueing lever is lowered.
6 Carefully remove the Stylus cover and adjust the
Counterweight again until the tone-arm is balanced.
Rear view
Clear a work area.
Ensure the packaging is the right-way up.
Open the packaging carefully.
Lift out each item, identify it, and carefully place it to one side.
Dust cover
Base unit with tone-arm
Turntable platter
Rubber mat
Head-shell with cartridge
Counterweight for the tone-arm
Hinges x 2
Cables x 3, comprising
USB cable (type-A - type-B)
Stereo phono plugs - Stereo phono plugs
Stereo phono sockets - 3.5mm stereo plug
45 r.p.m. adaptor holder with screws x 2
45 r.p.m. adaptor
Mains power adaptor with EU and UK pin options
A
N
T
I
-
S
K
A
T
I
N
G
1
2
3
4
0
Features
1. Counterweight
Used to set the tracking weight.
2. Anti-skating control
Used to set the anti-skating adjustment.
3. Cueing lever
Use to lower and raise the tone-arm.
4. Tone-arm rest and securing clip
Holds the tone-arm in place when not in use.
5. Tone-arm
6. Head-shell
Holds the cartridge and stylus.
7. 33 / 45 r.p.m. speed switch
Selects the speed for the record to be played.
8. Platter and rubber mat
Place the record here for playing.
9. 45 r.p.m. adaptor holder
10. Phono sockets (right and left)
 Audiooutputtoanamplier.
Red = Right channel; White = Left channel.
11. Pre-Amp On/Off Switch
 Controlsuseofthebuilt-inphonopreamplier.
If connected to a Line or Aux input set this switch to On.
12. USB port (see website for details on recording)
Connect to a computer for making recordings.
13. Auto Stop On/Off switch
Controls the use of the automatic switch off.
14. DC input socket
15. Power On/Off switch
continued overleaf...
STEP 1 - Assembling your turntableWhat is in the Box?
B - Attach the counterweight to the tone-arm
1 Slide the Counterweight on to the Tone-arm.
2 Rotate the Counterweight anti-clockwise (when
viewed from the front) until it engages and some
slight resistance is felt.
Note: The scale rotates freely. The counterweight
itself must be rotated in order to engage correctly
with the tone-arm. E - Attach the platter and mat
F - Attach the dust cover
G - Attach the adaptor holder
1 Unpack the Platter. Place the Platter on the
Spindle.
2Slowly rotate the platter by hand to ensure that it
moves freely.
3Place the Rubber mat on to the Platter.
1 Fit the two Hinges onto the Dust cover.
2 Locate the other end of the Hinges in the
two Sockets at the rear of the turntable
base.
3 Lower the Cover into place over the
platter and tone-arm.
1 Attach the 45 r.p.m. Adaptor holder onto the rear of the turntable
using a cross head screwdriver. Do not overtighten screws.
2 Place the 45 r.p.m. adaptor into the holder for storage.
A - Connect the head-shell to the tone-arm
Unwrap the base unit and take care not to put pressure on the tone-arm or
the cueing lever. Do not assemble the platter on to the base just yet.
1 Lock the Tone-arm with the securing clip.
2 Take the Head-shell and identify the locating pin. Do not
remove the stylus cover at this time.
3 Align the Locating pin on the head-shell with the slot
in the socket at the end of the tone-arm. Gently push.
4 Rotate the Locking ring (anti-clockwise when viewed
from the front) to pull the two parts together. Only
tighten by hand.
D - Set the tracking weight
1 When the Tone-arm is balanced, place it on its
rest using the securing clip. Carefully replace the
Stylus cover.
2 Keeping the counterweight in place, rotate the
Scale on the front of the counterweight to
zero.
3 Atracking weight of 2.0 grams is recommended for the supplied
cartridge.The tracking weight should not exceed 2.5 grams.
4 Rotate the Counterweight and Scale together so that the
counterweight moves further towards the
tone-arm pivot until the scale reads 2.0
grams.
5 Adjust the Anti-skating control so that it
also reads 2.0 grams. This should normally
match the chosen tracking weight.
A
N
T
I
-
S
K
A
T
I
N
G
1
2
3
4
0
C - Balance the tone-arm
Balance the tone-arm Cueing lever (to raise or
lower the tone-arm)
Head-shell
Stylus cover
Stylus
A
N
T
I
-
S
K
A
T
I
N
G
1
2
3
4
0
Note:Anincorrecttrackingweightcanhaveasignicanteffectonthequalityoftheaudiowhenplaying
records. If the tracking weight is set too low or too high then excessive wear to the stylus or damage
to the surface of the record may be caused.
9
1
2
3
4
5
6
8
7
10 11 12 13 14 15
When removing the stylus cover, do not touch the stylus. Damage caused to the stylus by mishandling
is not covered by the guarantee. When balancing the tone-arm it is important that the stylus never
contacts the turntable platter, mat or base.
Platter
Rubber
mat
Spindle
0
0.5
1
2
2.5
Counterweight
Scale
0
0.5
1
2
2.5
Rotate
Scale to 0
2
2.5
0
1
1.5
Rotate Counter
weight & scale
to 2grams
43
Head-shell
Stylus cover
Stylus
We recommend that all packaging is kept to allow the turntable to be safely transported in the future.
Head-shell
Stylus
cover
Locating pin Tone-arm
Rotate locking ring
Push

1 Set the Anti-skating control to zero, raise the Cueing lever and unclip the Tone-arm so that it
moves freely.
2 Hold the Head-shell.It is currently
unbalanced and will drift upwards.
3 Rotate the Counterweight so that
it moves further onto the Tone-arm.
4 Check the balance and lower the
Cueing lever to see if the tone-arm
falls, rises or remains level.
5 Adjust the Counterweight so that it
moves in or out until the Tone-arm
is balanced and remains level when
the cueing lever is lowered.
6 Carefully remove the Stylus cover and adjust the
Counterweight again until the tone-arm is balanced.
Rear view
Clear a work area.
Ensure the packaging is the right-way up.
Open the packaging carefully.
Lift out each item, identify it, and carefully place it to one side.
Dust cover
Base unit with tone-arm
Turntable platter
Rubber mat
Head-shell with cartridge
Counterweight for the tone-arm
Hinges x 2
Cables x 3, comprising
USB cable (type-A - type-B)
Stereo phono plugs - Stereo phono plugs
Stereo phono sockets - 3.5mm stereo plug
45 r.p.m. adaptor holder with screws x 2
45 r.p.m. adaptor
Mains power adaptor with EU and UK pin options
A
N
T
I
-
S
K
A
T
I
N
G
1
2
3
4
0
Features
1. Counterweight
Used to set the tracking weight.
2. Anti-skating control
Used to set the anti-skating adjustment.
3. Cueing lever
Use to lower and raise the tone-arm.
4. Tone-arm rest and securing clip
Holds the tone-arm in place when not in use.
5. Tone-arm
6. Head-shell
Holds the cartridge and stylus.
7. 33 / 45 r.p.m. speed switch
Selects the speed for the record to be played.
8. Platter and rubber mat
Place the record here for playing.
9. 45 r.p.m. adaptor holder
10. Phono sockets (right and left)
 Audiooutputtoanamplier.
Red = Right channel; White = Left channel.
11. Pre-Amp On/Off Switch
 Controlsuseofthebuilt-inphonopreamplier.
If connected to a Line orAux input set this switch to On.
12. USB port (see website for details on recording)
Connect to a computer for making recordings.
13. Auto Stop On/Off switch
Controls the use of the automatic switch off.
14. DC input socket
15. Power On/Off switch
continued overleaf...
STEP 1 - Assembling your turntableWhat is in the Box?
B - Attach the counterweight to the tone-arm
1 Slide the Counterweight on to the Tone-arm.
2 Rotate the Counterweight anti-clockwise (when
viewed from the front) until it engages and some
slight resistance is felt.
Note: The scale rotates freely. The counterweight
itself must be rotated in order to engage correctly
with the tone-arm. E - Attach the platter and mat
F - Attach the dust cover
G - Attach the adaptor holder
1 Unpack the Platter. Place the Platter on the
Spindle.
2Slowly rotate the platter by hand to ensure that it
moves freely.
3Place the Rubber mat on to the Platter.
1 Fit the two Hinges onto the Dust cover.
2 Locate the other end of the Hinges in the
two Sockets at the rear of the turntable
base.
3 Lower the Cover into place over the
platter and tone-arm.
1 Attach the 45 r.p.m. Adaptor holder onto the rear of the turntable
using a cross head screwdriver. Do not overtighten screws.
2 Place the 45 r.p.m. adaptor into the holder for storage.
A - Connect the head-shell to the tone-arm
Unwrap the base unit and take care not to put pressure on the tone-arm or
the cueing lever. Do not assemble the platter on to the base just yet.
1 Lock the Tone-arm with the securing clip.
2 Take the Head-shell and identify the locating pin. Do not
remove the stylus cover at this time.
3 Align the Locating pin on the head-shell with the slot
in the socket at the end of the tone-arm. Gently push.
4 Rotate the Locking ring (anti-clockwise when viewed
from the front) to pull the two parts together. Only
tighten by hand.
D - Set the tracking weight
1 When the Tone-arm is balanced, place it on its
rest using the securing clip. Carefully replace the
Stylus cover.
2 Keeping the counterweight in place, rotate the
Scale on the front of the counterweight to
zero.
3 Atracking weight of 2.0 grams is recommended for the supplied
cartridge.The tracking weight should not exceed 2.5 grams.
4 Rotate the Counterweight and Scale together so that the
counterweight moves further towards the
tone-arm pivot until the scale reads 2.0
grams.
5 Adjust the Anti-skating control so that it
also reads 2.0 grams. This should normally
match the chosen tracking weight.
A
N
T
I
-
S
K
A
T
I
N
G
1
2
3
4
0
C - Balance the tone-arm
Balance the tone-arm Cueing lever (to raise or
lower the tone-arm)
Head-shell
Stylus cover
Stylus
A
N
T
I
-
S
K
A
T
I
N
G
1
2
3
4
0
Note:Anincorrecttrackingweightcanhaveasignicanteffectonthequalityoftheaudiowhenplaying
records. If the tracking weight is set too low or too high then excessive wear to the stylus or damage
to the surface of the record may be caused.
9
1
2
3
4
5
6
8
7
10 11 12 13 14 15
When removing the stylus cover, do not touch the stylus. Damage caused to the stylus by mishandling
is not covered by the guarantee. When balancing the tone-arm it is important that the stylus never
contacts the turntable platter, mat or base.
Platter
Rubber
mat
Spindle
0
0.5
1
2
2.5
Counterweight
Scale
0
0.5
1
2
2.5
Rotate
Scale to 0
2
2.5
0
1
1.5
Rotate Counter
weight & scale
to 2grams
43
Head-shell
Stylus cover
Stylus
We recommend that all packaging is kept to allow the turntable to be safely transported in the future.
Head-shell
Stylus
cover
Locating pin Tone-arm
Rotate locking ring
Push

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com

8 At the end of the record, the turntable will
switch off. Note: The automatic switch off
feature is dependent on the placement of the
run-out-groove at the end of the record and may
take a few seconds to operate. If the turntable
switches off prematurely, you will need to set
the Auto Stop switch to Off.
9 Raise the Cueing lever and return the tone-
armtoitsrest.Theplattermayrotatebriey
during this step.
10 Lock the tone-arm in place with the securing
clip.
11 If not playing another record for a while it is
recommended to close the dust cover, switch
off the turntable and switch off the mains supply
to the turntable.
12 If you wish to stop playing a record before it
hasnished,usethecueinglevertoraisethe
stylus from the record before returning the
tone-arm to its support.
This product is guaranteed for twenty four months from the date of
purchase by the original owner against failure due to faulty workmanship
or component breakdown, subject to the procedure stated below.
Should any component or part fail during this guarantee period it will
be repaired or replaced free of charge.
The guarantee does not cover: 1. Damage resulting from incorrect use.
2.Consequentialdamage.3.Productwithremovedordefacedserial
numbers.
N.B. The stylus will not be replaced under this guarantee if it is
damaged or broken.
Procedure: Any claim under this guarantee should be made through
the dealer from whom the product was purchased. It is likely that your
Robertsdealerwillbeabletoattendtoanydefectquicklyandefciently,
but should it be necessary the dealer will return the product to the
company’s service department for attention. In the event that it is not
possible to return the product to the Roberts dealer from whom it was
purchased, please contact Roberts Radio using the contact details on the
www.robertsradio.com website.
For product repairs falling outside the guarantee period, please refer
to the “customer care” tab on the www.robertsradio.com website.
These statements do not affect the statutory rights of a consumer.
Designed & Engineered in the UK
Made in Taiwan
Direct-drive turntable with USB connection and
built-inpreamplier
Please read this manual before use
ROBERTS RADIO LIMITED
Roberts Radio Ltd, Stoney Lane, Whiston, Prescot, L35 2XW, UK
Glen Dimplex Europe Ltd, Airport Road, Cloghran, Co. Dublin, K67 VE08, Ireland
www.robertsradio.com
© 2021 Roberts Radio Limited
Issue 1a
2021-05-10
In the event of a malfunction due to electrostatic discharge, mains
power supply transients or short interruptions, remove the power for
30 seconds and then re-apply power to resume normal operation.
If the product is used in an environment with any ESD Immunity /
Radiated Immunity / Conducted Immunity disturbance, the product
may malfunction. It will automatically recover to normal when the ESD
Immunity / Radiated Immunity / Conducted Immunity disturbance
is stopped.
Electro-magnetic compatibility advice
DC Voltage
Power input 24V / 1.5A
Recycling This product bears the selective sorting
symbol for Waste Electrical and Electronic Equipment
(WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to
be recycled or dismantled to minimize its impact on the
environment. The user has the choice to give the product
to a competent recycling organization or to the retailer
whenbuyinganewelectricalorelectronicequipment.
Product markings
A - Audio connection Playing a record
Guarantee
B - Mains adaptor
C - Switch on
1 Assemble either the UK or
EU pins on to the Mains
power adaptor to suit the
mains sockets installed at
your location.
2 The AC adaptor should
be disconnected from the
mains supply and from the
turntable when not in use.
1 Plug the DC lead from the mains adaptor
into the DC input socket.
2 Plug the adaptor into a suitable mains
socket.
3 Switch on the mains socket and then
switch the Power On/Off switch On.
DC input socket On / Off switch
RT200
1 Ensure the record is clean and dust free. Use a record cleaner if
required.
2 Carefully place the record on the platter and set the Speed switch
to 33 or 45 r.p.m. as needed for the record.
3 Remove the Stylus cover, unclip the Tone-arm and raise the Cueing
lever.
4 Position the Tone-arm so that the stylus is centred above the
lead-in area of the record. The record should now rotate.
5 Lower the Cueing lever. The tone-arm will drop slowly and the
stylus should then settle into the groove at the start of the record
which will then start playing.
6 You may wish to gently lower the dust cover while the record is
playing. Do not let it close suddenly to avoid a sudden jolt to the
tone-arm and stylus.
7 Youwillbeabletolistentotherecordthroughyourconnectedequipment.
STEP 2 - Connecting STEP 3 - Playing a record
IMPORTANT: The mains adaptor is used as the means of
connecting the product to the mains supply. The mains socket
and any multi-way mains block used for the product must
remain accessible during normal use. In order to disconnect
the product from the mains, the mains adaptor should be
removed from the mains socket completely.
Use only the mains adaptor provided with the product, or a
genuine replacement provided by Roberts Radio. The use of
alternative adaptors will invalidate the guarantee.
• Your turntable and AC/DC adaptor should not be exposed
toliquidsorsteamandnoobjectslledwithliquids,such
as vases, shall be placed on the turntable or adaptor.
• It is recommended to operate the product such that there
is a minimum distance (10cm recommended) to adjacent
objects in order to ensure good ventilation.
• The ventilation of the product should not be restricted by
covering it with items such as newspapers, tablecloths,
curtains etc.
• Nonakedamesourcessuchaslightedcandlesshould
be placed on the product.
• It is recommended to avoid using or storing the product
at extremes of temperature. Avoid leaving the unit in cars,
on window sills, in direct sunlight etc.
• There are no user serviceable parts inside this product.
The head-shell, stylus and cartridge are considered to be
parts that the user may replace if so desired.
• Do not attempt to disassemble any part of the product.
• The product must be used in a moderate climate.
The name plate is located underneath the turntable.
Device with an
auxiliary input
Cable with two phono
plugs at each end
Radio with Auxiliary input socket
Cable with two phono
sockets to a 3.5mm plug
PRE AMP
OFF ON
PRE AMP
OFF ON
Safety
Specications
Mains AC 100 240 volts, 50/60Hz (adaptor)
(Use only the supplied adaptor)
Operating temperature range +5°C to +40°C
Cartridge Moving magnet type
Audio Technica AT-95E
   Loadimpedance47kΩ
Tracking weight 2.0 - 2.5 grams
Replacement stylus Audio Technica ATN-95E
Thecompanyreservestherighttoamendthespecicationwithoutnotice
AUTO STOP
OFF ON
AUTO STOP
OFF ON
Automatic stop
disabled
Automatic stop enabled
Note: Always use the cueing lever to lower and raise the tone-arm and stylus in order to
minimise the risk of damage to either the stylus or the record’s surface. When playing
records it is important to ensure that the stylus never contacts the turntable platter,
mat or turntable base. Damage caused to the stylus by mishandling is not covered by
the guarantee.
UK pins
EU pins
Note: In order to play music the turntable must be connected to a device providing
amplicationandoneormoreloudspeakers.
OR
PRE AMP
OFF ON
PRE AMP
OFF ON
Hi-Fi AmplifierSpeaker
Cable with two phono plugs at each end.
Connect ground wire at both ends if there is
hum or buzzing from the speakers.
Speaker
Hi-Fi System
Set Pre Amp to OFFifAmplierhasphonoinput
Set Pre Amp to ON for all other cases
PRE AMP
OFF ON
PRE AMP
OFF ON
To clean the turntable use a soft lint-free cloth, ideally made from
naturalbresinordertopreventabuild-upofstaticelectricitywhich
can attract dust. Do NOT use polish or any solvent based cleaners.
To remove dust from the mat on the platter, use a slightly damp
lint-freecloth,removingthematrstifneeded.Tocleanrecords,
only use a purpose designed record cleaning brush with the record
on the platter.
For support with using the recording function and for general
troubleshooting, please visit our website at www.robertsradio.com